ideal lux TL H35 Floor Lamp Instruction Manual

ideal lux TL H35 Floor Lamp

Product Information

Specifications

• Product Name: Stardust TL H35
• LED: 3W / 5V 1A
• Barcode: 8021696250878
• Color: Anthracite

Product Usage Instructions

Installation

The lighting fitting should be installed by a qualified electrician.

Charging

Charge the product using the provided plug for 4-5 hours. The green light indicates charging, and the red light indicates low battery.

Light Source Efficiency Class

This product comes with a light source with an energy efficiency class of F.

Replaceable Parts

The LED light source is replaceable by the end-user. Control gear can also be replaced by the end-user.

FAQ

Q: Can I replace the LED light source myself?

• A: Yes, the LED light source is replaceable by the end-user.

Q: How long should I charge the product for?

• A: Charge the product for 4-5 hours until the green light indicates it is fully charged.

Dimension

• LED 3W / 5V 1A 8021696250878 ANTHRACITE

Floor lamp

Features

ASSEMBLY INSTRUCTIONS

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION

QUALIFICATIONS THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN

• THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED.
• PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.

This product is provided with a light source with an efficient energy class.

• Light Source Model 8021696250878
• Energy Effificiency Class F
• Light Source (mA) MAX 850 mA
• Light Source (V) 2,9 V DC

LEGENDA ICONE

• Replaceable light source by an end-user.
• Replaceable LED light source by an end-user.
• Replaceable light source by authorized personnel only.
• Non-replaceable light source.
  • Upon the end of the life of the light source, the whole product will be replaced.
• Replaceable control gear by an end-user.
• Replaceable light source by authorized personnel only.
• Upon the end of the life of the control gear, the whole product will be replaced.

SAFETY INSTRUCTIONS

1. This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor, or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance, or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires were not suitable for recessed on normally flammable surfaces.
11. Luminaire is not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing the ceiling.
13. This fitting is only suitable for fixing the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps that do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class Il Electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
23. Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire is not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

• DEAL LUX s.r.l.
• Via Taglio Destro 32
• 30035 Mirano (VE) Italy
• www.ideal-lux.com

Documents / Resources

| ideal lux TL H35 Floor Lamp [pdf] Instruction Manual
TL H35 Floor Lamp, TL H35, Floor Lamp, Lamp
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>