QSFPTEK S5300-48T6X 48-Port Gigabit Ethernet Switch User Guide
- June 17, 2024
- QSFPTEK
Table of Contents
S5300-48T6X Quick Start Guide
Quick Start Guide V2.0
48-Port Gigabit Ethernet L3 Switch
48x 1G RJ45 Ports, with 6x 10G SFP+ Uplinks, Support
Stacking
Introduction
The S5300-48T6X is a L3 gigabit managed access Ethernet switch with 48x GE
RJ45 downlinks and 6x 10GE SFP+ uplinks. Effortlessly control and manage the
switch through both CLI and WEB interfaces. The S5300-48T6X layer 3 managed
switch is an excellent choice for enterprise network requirements, campus
networks, and SMBs.
We appreciate your decision to select S5300-48T6X. This manual is intended to
help you become acquainted with the switch design and provide instructions for
implementing the switches into your network.
Accessories
Hardware Overview
Front Panel Ports
| Ports | Description |
|---|---|
| Gigabit Ethernet Port | 100/1000BASE-T ports for Ethernet connection, with |
LINK/ACT indicators
10GE Port| SFP+ ports for 1/10G connection, with LINK/ACT indicators
CON Port| A baud rate of 9600bps, RJ45 interface
Front Panel LEDs
| LEDS | Description |
|---|---|
| RJ45 (1-48) | On |
| SFP+ (TE1-TE6) | On |
| SYS LED | / |
| PWR LED | / |
Back Panel
| Abbrev | Name | Description |
|---|---|---|
| Grounding column | The grounding column | The grounding column must be fine. |
| POWER | AC power supply | Input voltage: AC100~240V |
Installation Requirements
Tools Preparation
- Screwdriver
- Static-proof wristband
- Bolt
- Ethernet cable
- Other Ethernet terminal devices
- Control terminal
Safety Principles
Keep dustless and clean during or after the installation.
- Put the cover in a safe place.
- Put tools in the right place where they are not easily falling down.
- Put on relatively tight clothes, fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box.
- Put on protective glasses if the environment may cause damage to your eyes.
- Avoid incorrect operations that may cause damage to humans or devices.
Site Environment
- Make sure that the workshop is well-ventilated, the heat of electrical devices is welldischarged
- Avoid damaging devices by following the electrostatic discharge prevention procedure.
- S5300-48T6X Hardware Installation Manual
- Put the machine box in a place where cool air can blow off the heat inside the machine box.
- Make sure the machine box is sealed.
Mounting the Switch
Connecting the Power
- Plug the AC power cord to the switch power port on the back rear.
- Connect the other end of the power cord to an AC power source equipment.
Connecting the RJ45 Ports
- Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc.
- Connect the other end of the Ethernet cable to the switch RJ45 port.
Connecting the SFP+ Port
- Insert the SFP+ module into the SFP+ port.
- Plug a fiber patch cable into the SFP+ transceiver.
- Connect the other end of the fiber to the device that you want to realize data communication.
Connecting the Management Ports
Connecting the Console Port
- Prepare a console cable.
- Insert the RJ45 connector of the console cable into the console port on the switch.
- Connect the DB9 female connector on the other end of the console cable to the serial port on the computer host.
Configuring the Switch
Configuring the Switch Using the Web-based Interface
Step 1: Connect your computer to the switch using an Ethernet cable and open a
web browser.
Step 2: Set the IP address of the computer to 192.168.0.x (where “x” is any
number from 2 to 254) and the subnet mask to 255.255.255.0.
Step 3: Open a web browser and type http://192.168.0.2 in the address bar.
Enter the default username and password (admin/admin).
Step 4: Click sign-in to access the web-based configuration page.
Configuring the Switch Using the Console Port
Step 1: Use the console cable to directly connect the switch console port to
your computer.
Step 2: Launch the terminal simulation software such as Hyper Terminal on the
computer.
Step 3: Configure the parameters of the terminal emulation software as
follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow
control.
Step 4: Enter the default username
and password (admin/admin).
Troubleshooting
Hardware Fault Analysis
- Power and cooling systems—power and fan
- Port, cable and connection—ports on the front panel of the switch and the cables connecting these ports
Faults Relative to Power and Cooling System
Do the following checkups to help remove the fault:
- When the power on-off is at the “ON” location, check whether the fan works normally. If the fan does not work well, check the fan.
- If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3 “Requirements for Common Locations”.
- If the switch cannot be started and the PWR indicator is off, check the power.
Faults Relative to Port, Cable and Connection
Do the following checkups to help remove the fault:
- If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal.
- If the power on-off is at the “ON” location, check the power source and the power cable.
- If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control.
Support and Other Resources
- Contact us https://www.qsfptek.com/company/contact-us.html
- Customer Success https://www.qsfptek.com/resources/customer-success-stories
- Email support@qsfptek.com
Product Warranty
S5300 series switches are backed by a 5-year limited warranty supported by
QSFPTEK. You are eligible to apply for a return within 14 days and exchange
within 90 days of receiving them.
For more details about applying qualifications, please live chat or email
sales@qsfptek.com for support.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>