BRAYER BR4882 Portable Convector Heater Instruction Manual

BRAYER BR4882 Portable Convector Heater

CONVECTION HEATER

BR4882
A convection fan heater is intended for use as an additional heating unit, for heating of a small amenity room or its certain area.

DESCRIPTION

1. Hot air output

2. Display

3. Control panel

4. Front panel

5. Power switch «ON/OFF»

6. Feet (2 pcs.)
   Control panel

7. On/Off button « »

8. Power selection button « »

9. Open window detection button « »

10. Time/timer setting button « »

11. Operating modes programming button «ПРОГ»

12. Default program selection button «РЕЖИМ»

13. Program setting button « » или « »
    Display

14.  Remote control signal receiver

15. Icon for max power operation « »

16. Icon for low power operation « »

17. Timer operation icon « »

18. Temperature icon « »

19. Frost Protection icon « »

20. Open Window Detection icon « »

21. Numeric and alphabetic characters for operating
    modes

22. Remote control

23. On/off button « »

24. Power selection button « »

25. Open window detection button « »

26. Time/timer setting button « »

27. Operating modes programming button «ПРОГ»

28. Default program selection button «РЕЖИМ»

29. Program setting button « » или « »

30. Battery holder

INSTALLATION

ATTENTION!

• Portable convection fan heaters are intended for the use as a supplementary source of heat, for heating a small amenity room or its certain area. They are not intended for the use as main heating units.
• For additional protection it is reasonable to install a residual current device (RCD) with nominal operation current not exceeding 30 mA. To install an RCD, contact an electrical technician.

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation manual carefully before using the convection fan heater; after reading this manual, keep it for future reference.

• Use the unit for its intended purpose only, as it is stated in this manual.

• Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.

• Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.

• The three-wire power cord of the convection fan heater has a ground wire, and the power plug has a ground contact. Always connect the power plug to the socket with reliable grounding contact. In case of any inner short circuit, grounding reduces the risk of electric shock, because the current will pass through the ground wire.

• To avoid fire, do not use adapters for connecting the unit to the mains.

• To avoid mains overloading, do not switch on several electrical appliances with high power consumption at the same time.

• If you use an extension cord, make sure that the wire cross-section of the extension cord and the wire cross-section of the power cord of the convection fan heater match.

• Place the appliance vertically on an even, dry, moisture- and thermal -resistant surface, do not place it horizontally and do not turn it over.

• For floor placements, use the feet only.

• When mounting the unit on the wall, make sure that the mains socket is below the level of the unit body and easy to access.

• When mounting the unit on the wall, the distance from all sides of the unit body to any objects should be at least 300 mm, the mains socket must be below the level of the unit body and easy to access.

• Do not place the convection fan heater on soft surfaces, such as carpets with deep pile, sofas or beds.

• The distance between the front grid of the convection fan heater and the furniture should be at least 1 m.

• Do not use the convection fan heater in a limited space, for example, in built-in cabinets or wall niches.

• Do not use the appliance in small rooms, if there are people unable to leave the room on their own, unless they are constantly supervised.

• Do not use the unit if the room temperature is above +30ºС.

• Do not use the power cord as a carrying handle.

• Do not wind the power cord around the unit body.

• Provide that the power cord does not contact with hot surfaces and sharp furniture edges.

• Protect the appliance from impacts, dropping, vibrations and other mechanical stress.

• Do not use the appliance if the front glass panel is damaged.

• Avoid blocking the bottom air grid with foreign objects, do not cover the appliance during its operation.

• Do not use the unit to dry clothes or other household items.

• Do not use the unit in places where inflammable liquids are used or aerosols are sprayed, do not use the unit in the places where such liquids are stored.

• Do not use the unit outdoors. When using the unit in the bathroom, place the unit in such a way that the distance from the nearest faucet is at least 60 cm, and in no case splashes of water should fall on the unit and inside the body of the unit.

• Do not use the unit near swimming pools or other containers filled with water.

• If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water. Apply to the authorized service center for testing or repairing the unit.

• Do not touch the unit body, the power cord and the power plug with wet hands.

• It is not recommended to use the unit during lightning storms.

• During operation the convection fan heater body heats up strongly, do not touch hot parts of the unit body to avoid burns.

• Avoid getting burns by hot air.

• Never leave the unit connected to the mains unattended.

• Unplug the unit after usage or before cleaning.

• Switch the convection fan heater off and unplug the power cord plug from the mains socket.

• When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage or cause a short circuit.

• Do not immerse the unit into water or any other liquids.

• If water droplets fall on the convection fan heater body, switch it off and disconnect the power plug from the mains before touching the unit, then wipe the unit body with a dry cloth.

• For child safety reasons do not leave polyethylene bags used as packaging unattended.
  Attention! A lithium battery is used in the remote control. Prevent children from swallowing the lithium battery. If your child has swallowed a battery, seek immediate medical advice.

• The unit is not intended for usage by children.

• Do not leave children unattended to prevent using the unit as a toy.

• Do not allow children to touch the unit body, the power cord or the power plug during operation of the unit.

• Be especially careful if children or disabled persons are near the operating unit.

• During the unit operation and breaks between operation cycles, place the unit out of reach of children.

• The unit is not intended for usage by physically, sensory, psychically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.

• From time to time check the power cord integrity.

• If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.

• If a foreign smell appears, immediately stop using the unit, try to visually determine the cause of the foreign smell, a possible reason is a foreign object present on the heating element, if possible, remove the foreign object from the heating element, otherwise contact the service center.

• Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.

• To avoid damages, transport the unit in the original package.

• Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE THE FIRST USE

After the unit’s transportation or storage at negative temperature, unpack it, and wait for at least 3 hours before using it.

• Unpack the unit and remove all the packaging materials
• Keep the original package.
• Read the safety measures and operating recommendations.
• Check the delivery set.
• Examine the unit for damages, in case of damage do not plug it into the mains.
• Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When using the unit in the mains with 60 Hz frequency, the unit does not need any additional settings.
• Wipe the convection fan heater body with a slightly damp cloth and then wipe it dry.

ASSEMBLING AND INSTALLATION

Stand mode

• Turn over the unit body. Match the openings on the feet (6) with the corresponding openings in the bottom part of the unit body.
• Fix the feet (6) with the screws supplied with the unit.
• Turn over the unit and place it on an even steady surface.

Wall mounting
ATTENTION! When using the convection fan heater in the bathroom, position the unit so that the distance from the nearest faucet is at least 60 cm, and in no case should splashes of water fall on the body and inside the body of the unit. Before drilling holes in the wall, make sure that there is no electrical wiring or other communications at this place.

• When mounting the unit on the wall, the distance from all sides of the unit body to any objects should be at least 300 mm (pic. 2), the mains socket should be below the level of the unit body and easy to access.
• Do not use the feet (4) with the wheels (5) when mounting the unit on the wall.
• Using the four mounting screws, secure the upper brackets (fig. 2).
• Unscrew the mounting screw on the bottom of the appliance, install the bottom bracket and secure it using the screw removed earlier. (Fig. 2).
• Insert the dowels (pic. 3) into the drilled holes and tighten the fixing screws so that the fixing screw goes into the bracket (6).
• Align the screw heads with the holes in the upper brackets, slide the appliance down, make sure that the convection fan heater hangs without distortion
• Mark the location for drilling the hole for the bottom bracket (fig. 4).
• Remove the appliance from the wall.
• Drill a hole with a diameter of 6 mm in the wall to the required depth for mounting the bottom bracket
• Insert a dowel into the drilled hole.
• Align the screw heads with the holes in the upper brackets, slide the appliance down, make sure the convection fan heater is securely attached to the upper brackets.
• Mount the bottom bracket with a screw, make sure the convection fan heater is securely fixed to the wall.

USING THE CONVECTION FAN HEATER

• Place the convection fan heater vertically on an even dry moisture- and thermal-resistant surface, do not place it horizontally and do not turn it over.
• Use only the feet (6) when placing the unit on the floor.
• Do not place the convection fan heater on soft surfaces, such as carpets with high pile, sofas or beds.
• The distance between the convection fan heater and the furniture should be at least 1 m.
• To avoid mains overloading, do not switch on several electrical appliances with high power consumption at the same time.
• Insert the power plug into the mains socket.

REMOTE CONTROL (RC)
The control buttons on the remote control are similar to the control buttons on the control panel (3).
Attention! A lithium battery is used in the remote control. Prevent children from swallowing the lithium battery. If your child has swallowed a battery, seek immediate medical advice.

• Press the latch on the side and remove the battery
  holder (30), and install a CR2025 battery, strictly following
  the polarity.

• Install the battery holder (30) to its place.

Notes:

• If there is an insulating gasket in the RC battery compartment, remove the gasket.

• replace the battery in time;

• do not recharge the lithium battery;

• remove the battery if you are not going to use the
  appliance for a long time;

• remove the used battery from the remote control (22) and dispose of it.

• When using the remote control, point it at the front of the convection fan heater.

• The distance between the remote control and the appliance should not exceed 5 m, the coverage angle should be up to 30 degrees.

• Avoid direct sunlight on the remote control signal receiver (14), otherwise false switching on of control commands is possible.

BATTERY REPLACEMENT

• Remove the battery holder (30), remove the old battery, install a new CR2025 battery strictly following the polarity, install the battery holder (30) into the remote control.

DESCRIPTION OF THE POWER BUTTON AND THE BUTTONS ON THE CONTROL PANEL (3)

• Power switch (5) «ON/OFF». Set the switch (5) to the «ON» position to power on the appliance. At the end of operation, turn the appliance off by setting the switch (5) to the «OFF» position.
  Note: – operating mode buttons on the control panel (3) are touch-sensitive, and it is enough to touch the button to switch on the desired operating mode; each touch of the active button will be accompanied with a sound signal.

• On/Off button (7) « ». Touch the button (7) « » once or press the button (23) « » on the remote control (22) to turn on the convection fan heater. To turn the appliance off, touch the button (7) « » again or press the button (23) « »

TABLE OF ICONS DISPLAYED ON THE DISPLAY (2)

DATE AND TIME SETTING

1.  When the appliance is on, touch and hold the button (10) « » on the control panel (3) for 3 seconds or press and hold the button (26) « » on the remote control for 3 seconds.
2. The display (2) will show «d1» with characters (21) and will flash, then you should touch the buttons (13) « » or « » on the control panel (3) or press the buttons (29) « » or « » on the remote control (22) and select the current day of the week «d1, d2, d3, d4, d5, d6, d7» (Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, Sunday). Touch the button (10) « » on the control panel (3) again or press the button (26) «  » on the remote control (22) to confirm the setting ofthe current day of the week.
3. The appliance enters the hours setting mode. The numeric characters «hours» (21) on the display (2) will flash, then you should touch the buttons (13) « » or « » on the control panel (3) or press the buttons (29) « » or « » on the remote control (22) to set the time «hours». The current time «hours» can be set in the range from «00» to «23» hours. Touch the button (10) « » on the control panel (3) once or press the button (26) « » on the remote control (22) to confirm the setting of the current time «hours».
4. The appliance will enter the minutes setting mode. The numeric characters «minutes» (21) on the display (2) will flash, then you should touch the buttons (13) « » or « » on the control panel (3) or press the buttons (29) « » or « » on the remote control (22) to set the time «minutes». Touch the button (10) « » on the control panel (3) once or press the button (26) « » on the remote control (22) to confirm the setting of the current time «minutes».
5. To check whether the current day and current time settings are correct, touch the button (10) « » on the control panel (3) once in standby mode or press the button (26) « » on the remote control (22), while the display (2) will show the settings «Day» – «Hour» – «Minute», and the data will be displayed in turn for 1 second each, then the display (2) will switch to the temperature display.

Example: – if the current day is set as «Wednesday» and the current time is «12:45», then the display (2) will show «d3 – 12 – 45»in turn
Note: – when the appliance is turned on for the first time, the icon (17) « » on the display (2) will flash, reminding the user to set the current day and current time, please set the current day and current time settings and complete them before any other operation.

POWER SETTING

• When the appliance is turned on, the display (2) will show the icon (15) « » indicating that the appliance is turned on at full power of 1500 W.
• Touch the button (8) « » on the control panel (3) or press the button (24) « » on the remote control (22) to switch the power mode, while the display (2) will show the icon (16) « » indicating that the appliance is turned on at a low power of 750 W.

Note: – when the appliance is turned on for the first time, a small amount of smoke or foreign smell may appear; this is normal and is not covered by the warranty.

ROOM HEATING TEMPERATURE SETTING

• After setting the desired power of 750 W or 1500 W, touch the buttons (13) « » or « » on the control panel (3) or press the buttons (29) « » or « » on the remote control (22) to set the room heating temperature, the temperature will be displayed on display (2) with numeric characters (21) and the icon (14) « ». Temperature setting range from 5 to 350 С. The set temperature will get retained after 5 seconds if no further temperature changes are made.

Notes:

• the default temperature is set at 240 С;
• when the room temperature reaches the set value, the appliance will turn off; when the room temperature drops 10 С below the set temperature, the appliance will turn on and resume heating the room;
• setting the temperature is not possible in Frost Protection mode.

SELECTING DEFAULT OPERATING MODES

• When the appliance is turned on, by touching the button (12) «РЕЖИМ» on the control panel (3) or pressing the button (28) «РЕЖИМ» on the remote control (22), select an appliance operation mode «PI, P2, P3, P4, P5, UP».
• Operating modes «P1, P2, P3, P4, P5» are set by default.
• Operating mode «UP» is a customized setting for the room heating program, the description of the program setting is described below.

Notes:

• Frost Protection function is activated when the room temperature is below +50 С, and will keep the room temperature at +5ºC, preventing the water pipes from freezing.
• to achieve a comfortable temperature, you can set the power and temperature of the room heating.

TIMER CONFIGURATION

• Set the default operating mode «P1» (see section above), double-tap the button (10) « » on the control panel (3) or double-push the button (26) « » on the remote control (22), then the icon (17) « » on the display (2) will flash, and you will need to touch the buttons (13) « » or « » on the control panel (3) or press the buttons (29) « » or « » on the remote control (22) to set the timer operation time. The timer operating time setting range is from 0 to 24 hours. The timer operating time will be automatically saved 5 seconds after setting. Icon (17) « » on the display (2) will stop flashing, and the numeric characters (21) on the display (2) will show the countdown until the appliance turns off.
• To cancel the timer function, double-tap the button (10) « » on the control panel (3) or press the button (26) « » twice on the remote control (22), while the icon (17) « » on the display (2) will go out.
• You can turn off the timer by touching the button (12) «РЕЖИМ» on the control panel (3) or by pressing the button (28) «РЕЖИМ» on the remote control (22), while the icon (17) « » on the display (2) will go out.

CUSTOMIZATION PROGRAM «UP»

1. When the appliance is turned on, by touching the button (12) «РЕЖИМ» on the control panel (3) or pressing the button (28) «РЕЖИМ» on the remote control (22), select the operating mode «UP», then touch the button (11) «ПРОГ» on the control panel (3) or press the button (27) «ПРОГ» on the remote control (22) to activate the customization program.

2. The display (2) will show the character «d1» (Monday), to start setting the program «d1» (Monday), touch the button (13) « » or « » on the control panel (3) or press the button (29) « » or « » on the remote control (22), while the display (2) will show a flashing icon (15) « ». By touching the buttons (13) « » or « »on the control panel (3) or pressing the buttons (29) « » or « » on the remote control (22), to set the start time of the program; the time can be set in the range from «00» to «23» hours. Touch the button (10) « » on the control panel (3) once or press the button (26) « » on the remote control (22) to confirm the program start time setting.

3. The appliance will enter the mode of setting the end time of the program. To set the end time of the program, touch the buttons (13) « » or « » on the control panel (3) or press the buttons (29) « » or « » on the remote control (22), to confirm the end time of the program, touch the button (10) « » on the control panel (3) or press the button (26) « » on the remote control (22).

4. The appliance will automatically switch to the further setting mode of the program «UP», while the display (2) will show the character «d2» (Tuesday), and the flashing icon (15) « ». Set the start time of the program and the end time of the program «d2» (Tuesday) as described in points 2 and 3.

5. Set the individual operation of the customization program «UP» for the following days of the week «d3, d4, d5, d6, d7» (Wednesday, Thursday, Friday, Saturday, Sunday), similar to the previous points of the section.

6. After setting the start time and end time of the program «d3, d4, d5, d6, d7» (Wednesday, Thursday, Friday, Saturday, Sunday), do not forget to touch the button (10) « » once on the control panel (3) or press the button (26) « » on the remote control (22) to confirm the time settings, while the icon (15) « » will\ stop flashing.
   Notes:

   • if within 2 minutes no actions are performed to set up the program «UP» , the appliance will go into standby mode.
   • during operation, you can reduce or increase the room heating power by touching the button (8) « » on the control panel (3) or pressing the button (24) « » on the remote control (22) , while the display (2) will show the icons (15) « » (maximum power 1500 W) or (16) « » (low power 750 W) are displayed.
   • regardless of the set periods of the customization program «UP», the display (2) will show the icon of Frost Protection function (19) « », if the room temperature drops below +5ºC, the appliance will turn on and keep the temperature in the room at +5ºC.

7. To check the settings for the operation of the customization program «UP», touch and hold the button (11) «ПРОГ» for 3 seconds on the control panel (3) or press and hold the button (27) «ПРОГ» for 3 seconds on the remote control ( 22). By repeatedly touching the button (11) «ПРОГ» or pressing the button (27) « ПРОГ» check the correctness of the start and end timeof the program «UP», while the display (2) will show the characters «d1, d2, d3, d4, d5, d6, d7» (Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, Sunday) and the set start and end times for the customization program «UP».

OPEN WINDOW DETECTION FUNCTION

• When the appliance is turned on, touch the button (9) « » once on the control panel (3) or press the button (25) « » on the remote control (22), while the display (2) will show a flashing icon (20) « ». To disable the open window detection function, touch the button (9) « » on the control panel (3) again or press the button (25) « » on the remote control (22), while the icon (25) « » will go out on the display (2) .
• When the open window detection function is enabled, the appliance operates in-room heating mode, but if the room temperature drops by 5°C in 10 minutes, the appliance will perceive this phenomenon as the possibility of an accidental opening of the window. Within the next 30 minutes, if the room temperature does not rise, the room heating will stop and the appliance will turn off. The icon (25) « » on the display (2) will stop flashing and remain lit, reminding the user to close the window.
• After closing the window, touch the button (9) « » on the control panel (3) or press the button (25) « » on the remote control (22) to restore the open window detection function, while the icon (25) « » on the display (2) will start flashing again.

CHILD SAFETY LOCK FUNCTION

• When the appliance is turned on, simultaneously touch the buttons (13) « » or « » on the control panel (3) or simultaneously press the buttons (29) « » or « » on the remote control (22) and hold them for 3 seconds, while icon «[ ]» will be displayed on the display ( 2), all control buttons will no longer be active.
• To disable the child safety lock function, simultaneously touch the buttons (13) « » and « » on the control panel (3) or simultaneously press the buttons (29) « » and « » on the remote control (22) for 3 seconds.

SWITCHING OFF THE CONVECTION FAN HEATER

• To finish operation, touch the button (7) « » once or press the button (23) « » once on the remote control (22), and the appliance will turn off.
• To turn off the power, turn the switch (5) to the «OFF» position and unplug the power cord from the electrical outlet.

RESTORING THE FACTORY SETTINGS

• To restore factory settings, turn off the power by setting the switch (5) to the «OFF» position, touch and hold the button (13) « », then connect the power by setting the power switch (5) to the «ON» position, and the appliance will return to factory default settings.

AUTOMATIC EMERGENCY SWITCH-OFF FUNCTION IF THE OUTGOING AIR IS TOO HOT

• If the outgoing air temperature exceeds the acceptable value, the automated thermal switch will switch off the convection fan heater.
• Set the power switch (5) to the position «OFF» and unplug the unit, let the unit cool down for approximately 15-25 minutes (depending on the air temperature in the room) and only after that you can switch the unit on again.
• Make sure that the upper and bottom air grids are not blocked with foreign objects.
• Insert the power plug into the mains socket and switch the unit on.
•  If the convection fan heater does not switch on, it may be caused by another malfunction. In this case apply to a service center for repairing of the unit.

PROTECTION FROM DROPPING

• If the convection fan heater accidentally falls or tilts too much, the fall protection system will switch off the unit.
• Set the convection fan heater into the vertical position, and the unit will resume operation.

Note: place the unit on an even dry and steady surface to prevent it from dropping.

CLEANING AND MAINTENANCE

• Before cleaning the convection fan heater set the power switch (5) to the position «OFF», and make sure that the power plug is not inserted into the mains socket.
• Wipe the unit body with a slightly damp cloth and then wipe it dry.
• You can use glass cleaner to clean the front glass panel.
• Do not use liquid detergents, abrasive cleaners and any solvents to clean the unit.
• To avoid the risk of electric shock provide that no water or other liquid gets into the unit body.
• To clean the air grids, use a vacuum cleaner with a corresponding attachment.

STORAGE

• After cleaning put the convection fan heater away for storage in a dry cool place away from children and disabled persons.
• Before using the convection fan heater next time, it is recommended to check the heater operability and integrity of the power cord and plug.

DELIVERY SET

1. Convection fan heater – 1 pc.
2. Feet – 2 pcs.
3. Working instruction – 1 pc.
4. Mounting brackets with a set of fasteners – 1 pc.

TECHNICAL SPECIFICATIONS

• Power supply: 220-240 V, ~ 50-60 Hz
• Rated input power: 1500 W
• Heating area: 20 m²
• Protection degree: IP24

RECYCLING
To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after the expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling. The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner. For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product.

The manufacturer reserves the right to change the design, structure and specifications not affecting the general operating principles of the unit, without prior notice.
The unit operating life is 3 years
The manufacturing date is specified in the serial number. In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

References

• BRAYER - официальный сайт австрийского бренда бытовой техники

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>