AUPR2110 12 Ton A Frame Hydraulic Press Instruction Manual
- June 1, 2024
- AUPR
Table of Contents
AUPR2110 12 Ton A Frame Hydraulic Press
THANK YOU FOR BUYING OUR TOOLS
You can purchase additional items on our web site.
Your new 12 Ton A-Frame Hydraulic Press (no gauge) has been engineered and
manufactured by our company with high standards for dependability, ease of
operation and operator safety. Please pay close attention to the rules for
safe operation, warnings and cautions. If you use your machine properly and
only for what it is intended, you will enjoy years of safe and reliable
service.
GENERAL SAFETY RULES
WARNING : When using the tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment!
-
Work area conditions. Cluttered areas invite injuries.
-
Additional work area conditions. Do not use machines or power tools in damp or wet locations.
Do not expose to rain. Keep work area well lit. -
Keep children away. Children must never be allowed in the work area. Do not let them handle machines , tools or extension cords.
-
Store idle equipment. When not in use tools must be stored in a dry location to inhibit rust.
Always lock up tools and keep them out of the reach of children. -
Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and safer at the rate for which it was intended. Do not modify this tool and do not use this tool for a purpose for which it was not intended.
-
Dress properly. Do not wear loose clothing or jewelry as they can get caught in moving parts.
Protective, electrically non conductive clothing and non skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. -
Use eye protection. Always wear ANSI approved impact safety glasses underneath a full face shield during use. Also wear heavy duty work gloves.
-
Do not over reach. Keep proper footing and balance at all times. Do not reach over or across running machines.
-
Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. The handles must be kept clean, dry and free from oil and grease at all times.
-
Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the tool or machine work surface before starting work.
-
Stay alert. Watch what you are doing. Use common sense. Do not operate any tool when you are tired.
-
Check for damaged parts. Before using any tool, any parts that appear damaged should be carefully checked to determine that it will operate properly and perform its intended function. Any part that is damaged should be replaced.
-
Replacement parts and accessories. When servicing use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool.
Approved accessories are available from our company. -
Do not operate tools if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs.
WARNING : the warnings ,cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which can not be built into this product, but must be supplied by the operator.
ASSEMBLY
| PART | DESCRIPTION | QTY | |
|---|---|---|---|
| 1 | Bolt Ml6X60 | 2 | |
| 2 | 016 Washer | 4 | |
| 3 | 016 | Spring Washer | 4 |
| 4 | Ml6 Nut | 4 | |
| 5 | Bolt M8X50 | 2 | |
| 6 | 8 Washer | 2 | |
| 7 | MS Nut | 2 | |
| 8 | Bolt M16Xl40 | 2 | |
| 9 | Bolt MIOX25 | 12 | |
| 10 | 010 Washer | 12 | |
| 11 | 010 | Spring Washer | 12 |
| 12 | MlO Nut | 12 | |
| 13 | Spring | 2 | |
| 14 | Bolt | 2 | |
| PART | OESCR I PT I ON | QTY | |
| --- | --- | --- | |
| 15 | Handle | 1 | |
| 16 | M8 Nut | 2 | |
| 17 | Upper beam | 1 | |
| 18 | Support 1 | 4 | |
| 19 | Pump | 1 | |
| 20 | Pump Base | 1 | |
| 21 | Part 1 | 3 | |
| 22 | Base section | 2 | |
| 23 | Rod | 2 | |
| 24 | Block | 2 | |
| 25 | Frame | 1 | |
| 26 | Support Left | 2 | |
| 27 | Support Right | 2 | |
UNPACKING
INSTRUCTIONS
When unpacking the tool:
- Carefully remove the tool and accessories from the box.
- Make sure that all items listed in the packing list are included.
- Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
- Do not discard the packing material until you have carefully inspected and successfully operated the tool.
WARNING : When using the tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.
INSTRUCTION
This PRODUCT has many features which make it’s use more pleasant and
enjoyable. Safety,
performance, and dependability have been given top priority in the design of
this product making it easy to maintain and operate.
WARNING: Do not attempt to use this product until you thoroughly read and
completely understand the operator’s manual. Pay close attention to the safety
rules, including Dangers, Warnings, and Cautions. If you use your product
properly and only as intended, you will enjoy years of safe, reliable service.
Look for this symbol to point out important safety precautions. It means
attention!!! Your safety is involved.
WARNING: The operation of any tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye protection which is marked to comply with ANSI Z87 .1.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>