OMRON HEM-6140-E MIT Quick Check 3 Wrist Blood Pressure Monitor User Guide
- June 17, 2024
- Omron
Table of Contents
OMRON HEM-6140-E MIT Quick Check 3 Wrist Blood Pressure Monitor User Guide
Introduction
Thank you for purchasing the OMRON MIT Quick Check 3 Wrist Blood Pressure Monitor.
The OMRON MIT Quick Check 3 is a compact and easy to use blood pressure monitor, operating on the oscillometric principle. It measures your blood pressure and pulse rate simply and quickly. For comfortable controlled inflation without the need of pressure pre-setting or re-inflation the device uses its advanced “IntelliSense” technology.
Intended Use
This product is designed to measure the blood pressure and pulse rate of
people within the range of the designated wrist cuff. It is mainly designed
for general household use.
Please read this instruction manual thoroughly before using the unit.
Please keep for future reference. For specific information about your own blood pressure, CONSULT YOUR DOCTOR.
Important Safety Information
Consult your doctor prior to using in pregnancy or if diagnosed with arrhythmia or arteriosclerosis.
Warning:
- Indicates a potentially hazardous situation which, if not avoided, could result in death or injury.
(General Usage)
- Always consult your doctor. Self-diagnosis of measurement results and self-treatment are dangerous.
- People with severe blood flow problems, or blood disorders, should consult a doctor before using the unit, as cuff inflation can cause internal bleeding.
Battery Usage)
- If battery fluid should get in your eyes, immediately rinse with plenty of clean water. Consult a immediately.
Caution:
- Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to the user or patient or damage to the equipment or other property.
(General Usage)
- Do not leave the unit unattended with infants or persons who cannot express their consent.
- Do not use the unit for any purpose other than measuring blood pressure.
- Do not use a mobile phone or other devices that emit electromagnetic fields, near the unit. This may result in incorrect operation of the unit.
- Do not disassemble the unit or wrist cuff.
- Do not operate the unit in a moving vehicle (car, airplane).
(Battery Usage)
- If battery fluid should get on your skin or clothing, immediately rinse with plenty of clean water.
- Use only two “AAA” alkaline or manganese batteries with this unit. Do not use other types of batteries.
- Do not insert the batteries with their polarities incorrectly aligned.
- Replace old batteries with new ones immediately. Replace both batteries at the same time.
- Remove the batteries if the unit will not be used for three months or more.
- Do not use new and used batteries together.
General Precautions
- Do not apply strong shocks and vibrations to or drop the unit.
- Do not take measurements after bathing, drinking alcohol or caffeine, smoking, exercising or eating.
- Do not inflate the wrist cuff when it is not wrapped around your wrist.
- Read and follow the “Important information regarding Electro Magnetic Compatibility (EMC)” in the Technical Data Section.
- Read and follow the “Correct Disposal of This Product” in the Technical Data Section when disposing of the device and any used accessories or optional parts.
Know your unit
Main unit:
Components :
2 “AAA” Alkaline Batteries
Instruction Manual
Storage Case
Display:
Display symbols:
Irregular Heartbeat Symbol
When the monitor detects an irregular rhythm two or more times during the measurement, the irregular heartbeat symbol will appear on the display with the measurement values. An irregular heartbeat rhythm is defined as a rhythm that is 25% less or 25% more than the average rhythm detected while the monitor is measuring the systolic and diastolic blood pressure. If the irregular heartbeat symbol displays with your measurement results, we recommend you consult your physician. Follow the directions of your physician
Cuff Wrap Guide Symbol ( )
If the cuff was wrapped too loosely, it may cause unreliable values. If the
wrapping of cuff is too loose, the cuff wrap guide symbol appears. Otherwise
appears. This is the function which is used as an aid in determining if the
cuff is wrapped snugly enough.
Blood pressure Level Indicator
Blood pressure level indicator will light up between the systolic blood
pressure and the diastolic blood pressure.
2013 ESH/ESC Guidelines for the management of arterial hypertension
Recent research suggests that the following values can be used as a guide to
high blood pressure for measurements taken in office or at home.
| Office| Home
---|---|---
Systolic Blood Pressure| 140 mmHg| 135 mmHg
Diastolic Blood Pressure| 90 mmHg| 85 mmHg
Preparation
Installing/Replacing the Batteries
Remove the battery cover.
Insert two 1.5V “AAA” batteries as indicated in the battery compartment and then replace the battery cover.
Notes:
- If the battery low symbol ( ) appears on the display, turn off the unit then replace both batteries at the same time.
- The measurement values continue to be stored in memory even after the batteries are replaced.
Disposal of used batteries should be carried out in accordance with the national regulations for the disposal of batteries.
Setting the Date and Time
Press and hold the button until the year flashes on the display.
Set the monitor to the correct date and time before taking a measurement for
the first time
Press the START/STOP button to store the setting.
Notes:
- If the batteries have been removed, the date and time setting will need to be reset.
- If the date and time are not set, “-:–” appears during or after measuremen
Using the Unit
Applying the Wrist Cuff
Do not apply over clothing.
Place the wrist cuff over your wrist.
Your palm should face upward.
Wrap the wrist cuff around your wrist.
Wrap the wrist cuff securely around the wrist for taking accurate measurements.
**Make sure that the wrist cuff does not cover the protruding part of the wrist bone (ulna) on the outside of the wrist.
**
Note: You can take a measurement on either your left or right wrist
How to Sit Correctly
To take a measurement, you need to be relaxed and comfortably seated, under comfortable room temperature. No bathing, drinking alcohol or caffeine, smoking, exercising or eating 30 minutes before taking a measurement
- Sit on a chair with your feet flat on the floor.
- Sit upright with your back straight.
- The cuff should be at the same level as your heart
- Relax your wrist and hand. Do not bend your wrist back, clench your fist, or bend your wrist forward.
Taking a Reading
Notes:
- To cancel a measurement, press the START/STOP button at any time during measurement.
- Remain still while taking a measurement.
Press the START/STOP button.
All the symbols appear on the display. The wrist cuff will start to inflate
automatically
Undo the wrist cuff and remove the unit.
Press the START/STOP button to turn off the monitor.
The monitor automatically stores the measurement in its memory. It will
automatically turn off after two minutes.
Notes:
- Wait 2 – 3 minutes before taking another blood pressure measurement. Waiting between readings allows the arteries to return to the condition prior to taking the blood pressure measurement.
- The blood pressure can differ between the right arm and the left arm, and therefore also the measured blood pressure values can be different. OMRON recommends to always use the same arm for measurement. If the values between the two arms differ substantially, please check with your physician which arm to use for your measurement.
Using the Memory Function
The unit automatically stores up to 60 sets of measurement values (blood
pressure and pulse rate).
Notes:
- If the memory is full, the monitor will delete the oldest readings.
- When viewing the reading taken without setting the date and time, “-:–” is displayed instead of the date and time.
To View the Readings Stored in Memory
Press the button, the latest value is displayed
The Memory number appears for a second before the pulse rate is displayed. The newest set is numbered “1
Press the button repeatedly to view the readings stored in memory.
To Delete All the Values Stored in Memory
When the memory symbol ( ) appears, first press the button. Then while holding
it down, press the START/STOP button simultaneously for about 2 – 3 seconds
Note: You cannot partially delete the stored readings.
Troubleshooting and Maintenance
The Icons and Error Messages
Error Display
| Cause| Re medy
---|---|---
| Irregular heartbeats are detected| Remove the wrist cuff. Wait 2 – 3 minutes
and then take another measurement. Repeat the steps in section 3.3. If this
error continues to appear, contact your doctor.
Blink| Irregular heartbeats are detected.| You should replace them with new
ones ahead of time. Refer to section 2.1.
Lit| The batteries are low.| You should replace them with new ones at once.
Refer to section 2.1.
| Wrist cuff not applied correctly| Apply the wrist cuff correctly. Refer to
section 3.1.
| Movement during measurement.| Repeat Measurement while remaining still and
refraining from talking during the measurement. Refer to section 3.3.
| Wrist cuff not applied correctly, or movement during measurement.| Apply the
wrist cuff correctly and repeat measurement while remaining still and
refraining from talking during the measurement. Refer to section 3.1 and 3.3.
| Device error.| Contact your MORON retail outlet or distributo
Note: The irregular heartbeat symbol ( ) may also be displayed with error messages.
Problem
| Cause|
Remedy
|
---|---|---|---
The reading is extremely low (or NV.
|
The wrist cuff is not at heart level.
| Measure while in the correct posture.Refer to section 3.2.|
The cuff is not wrapped snugly around the west.|
Wrap the cuff correctly. Refer to section 3.1.
|
The arms and shoulders are tense.| Relax and try taking the measurement again.
Refer to section 3.3.|
Movement or talking during measurement.|
Remain Olt and do not talk during Measurement Refer to erection 3.3.
|
ist cuff pressure does not rise.
| Air is leaking from the wrist cuff.| Consult your OMRON retail outlet or
distributor.|
Wrist cuff deflates too soon| The wrest cuff is loose.|
Apply the cuff correctly so that it is finny wrapped around the wrist. Refer to section 3.1.
|
|
The blood pressures different each time. The read ng isextremely low (or high).
|
Blood pressure readings constantly vary with time of day and how relaxed you are. Take several deep breaths and try to remain relaxed before taking a measurement.
|
The unit loses power during measurement.
| The batteries are exhausted.| Replace the batterieswith new ones.Refer to
section 2.1.|
Nothing happens when you press the buttons.|
The batteries have been insertedincorrectry.|
Insert the batteries with the correct (•/-) polarity. Refer to section 2.1.
|
Other problems.
| · Press the START/STOP button and repeat measurement.•· If the problem con inues. try replacing the batteries with new ones.If this still does not solve the problem. contact your OMRON retail outlet or distributor.|
Maintenance To protect your unit from damage, please observe the following:
- Do not subject the main unit and the cuff to extreme temperatures, humidity, moisture or direct sunlight.
- Do not disassemble the unit.
- Do not subject the unit to strong shocks or vibrations (for example, dropping the unit on the floor).
- Do not use volatile liquids to clean the main unit.
- Do not wash the cuff or immerse it in water.
- Do not use petrol, thinners or similar solvents to clean the cuff.
- Do not carry out repairs of any kind yourself. If a defect occurs, consult your OMRON retail outlet or distributor as mentioned on the packaging
- The unit should be cleaned with a soft, dry cloth.
- Use a soft, moistened cloth and soap to clean the cuff.
- Keep the unit in its storage case when not in use.
- Fold the cuff into the storage case
Do not store the unit in the following situations:
- If the unit is wet.
- Locations exposed to extreme temperatures, humidity, direct sunlight, dust or corrosive vapours.
- Locations exposed to vibrations, shocks or where it will be at an angle.
Calibration and Service
- The accuracy of this blood pressure monitor has been carefully tested and is designed for a long service life.
- It is generally recommended to have the unit inspected every two years to ensure correct functioning and accuracy. Please consult your authorised OMRON dealer or the OMRON Customer Service at the address given on the packaging or attached literature
Technical Data
Product description | OMRON Wrist Blood Pressure Monitor |
---|---|
Model | MIT Quick Check 3 (HEM-6140-E) |
Display | LCD Digital Display |
Measurement method | Oscillometric method |
Measurement range | Pressure: 0 to 299 mmHg Pulse: 40 to 180 beats/min |
Accuracy | Pressure: ±3 mmHg Pulse: ±5% of display reading |
Inflation | Automatic inflation by pump |
Deflation | Automatic rapid deflation |
Memory | 60 Measurements |
Power source | 2 “AAA” batteries 1.5V |
Battery life | Approx. 300 measurements with new alkaline batteries at a room |
temperature of 23°C
Applied part| = Type BF
Protection against electric shock| Internally powered ME equipmen
Operating temperature/ Humidity| +10 to +40°C / Maximum: 15 to 85% RH
Storage temperature/ humidity/air pressure| -20 to +60°C / Maximum: 10 to 95%
RH / 700 to 1060hPa
Console weight| Approximately 123g without batteries
Outer dimensions| Approximately 86.7 (w) mm x 67 (h) mm x 28 (d) mm (without
the wrist cuff)
Measurable circumference| Approximately 13.5 to 21.5 cm
Cuff material| Nylon and polyester
Package content| Main unit, storage case, battery set, instruction manua
Note: Subject to technical modification without prior notice.
CE0197
- This device fulfils the provisions of EC directive 93/42/EEC (Medical Device Directive).
- This blood pressure monitor is designed according to the European Standard EN1060, Non-invasive sphygmomanometers Part 1: General Requirements and Part 3: Supplementary requirements for electromechanical blood pressure measuring systems.
- This OMRON product is produced under the strict quality system of OMRON HEALTHCARE Co. Ltd., Japan. The Core component for OMRON blood pressure monitors, which is the Pressure Sensor, is produced in Japan
Important information regarding Electro Magnetic Compatibility (EMC)
With the increased number of electronic devices such as PC’s and mobile (cellular) telephones, medical devices in use may be susceptible to electromagnetic interference from other devices. Electromagnetic interference may result in incorrect operation of the medical device and create a potentially unsafe situation. Medical devices should also not interfere with other devices.
In order to regulate the requirements for EMC (Electro Magnetic Compatibility) with the aim to prevent unsafe product situations, the EN60601-1-2:2007 standard has been implemented. This standard defines the levels of immunity to electromagnetic interferences as well as maximum levels of electromagnetic emissions for medical devices.
This medical device manufactured by OMRON HEALTHCARE conforms to this EN60601-1-2:2007 standard for both immunity and emissions. Nevertheless, special precautions need to be observed:
- Do not use mobile (cellular) telephones and other devices, which generate strong electrical or electromagnetic fields, near the medical device. This may result in incorrect operation of the unit and create a potentially unsafe situation. Recommendation is to keep a minimum distance of 7 m. Verify correct operation of the device in case the distance is shorter.
Further documentation in accordance with EN60601-1-2:2007 is available at OMRON HEALTHCARE EUROPE at the address mentioned in this instruction manual. Documentation is also available at www.omron-healthcare.com.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
This marking shown on the product or its literature, indicates that it should
not be disposed of, with other household wastes at the end of its working
life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this product from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can return this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Warranty
Thank you for buying an OMRON product. This product is constructed of high quality materials and great care has been taken in its manufacturing. It is designed to give you every satisfaction, provided that it is properly operated and maintained as described in the instruction manual.
This product is guaranteed by OMRON for a period of 2 years after the date of
purchase. The proper construction, workmanship and materials of this product
is guaranteed by OMRON. During this period of guarantee OMRON will, without
charge for labour or parts, repair or replace the defect product or any
defective parts. The guarantee does not cover any of the following:
a. Transport costs and risks of transport.
b. Costs for repairs and / or defects resulting from repairs done by
unauthorised persons.
c. Periodic check-ups and maintenance.
d. Failure or wear of attachments other than the main device itself,
unless explicitly guaranteed above.
e. Costs arising due to non-acceptance of a claim (those will be charged
for).
f. Damages of any kind including personal caused accidentally or from
misuse.
g. Calibration service is not included within the guarantee. Should
guarantee service be required please apply to the dealer whom the product was
purchased from or an authorised OMRON distributor. For the address refer to
the product packaging / literature or to your specialised retailer.
If you have difficulties in finding OMRON customer services, contact us for
information.
www.omron-healthcare.com
Repair or replacement under the guarantee does not give rise to any extension or renewal of the guarantee period.
The guarantee will be granted only if the complete product is returned together with the original invoice / cash ticket issued to the consumer by the retailer.
Some Useful Information about Blood Pressure
What is Blood Pressure?
Blood pressure is a measure of the force of blood flowing against the walls of
the arteries. Arterial blood pressure is constantly changing during the course
of the heart’s cycle. The highest pressure in the cycle is called the Systolic
Blood Pressure; the lowest is the Diastolic Blood Pressure. Both pressures,
the Systolic and Diastolic, are necessary to enable a physician to evaluate
the status of a patient’s blood pressure.
What is Arrhythmia?
Arrhythmia is a condition where the heartbeat rhythm is abnormal due to flaws
in the bio-electrical system that drives the heartbeat. Typical symptoms are
skipped heartbeats, premature contraction, an abnormally rapid (tachycardia)
or slow (bradycardia) pulse.
Why is it a Good Thing to measure Blood Pressure at Home?
Many factors such as physical activity, anxiety, or the time of day, can
influence your blood pressure. A single measurement may not be sufficient for
an accurate diagnosis. Thus it is best to try and measure your blood pressure
at the same time each day, to get an accurate indication of any changes in
blood pressure. Blood pressure is typically low in the morning and increases
from afternoon to evening. It is lower in the summer and higher in the winter
How are hypertension and irregular heartbeat linked to stroke?
Hypertension (high blood pressure) and atrial fibrillation are two major risk
factors of stroke. Irregular heartbeat is a potential indicator of atrial
fibrillation Omron Blood Pressure monitors can help to detect hypertension and
irregular heartbeat*. If either or both are indicated by the device, we
recommend to consult your doctor.
NOTE: Diagnosis can only be made by a doctor
Irregular heartbeat detection is available on most Omron blood pressure
monitors.
Manufacturer **ill
| OMRON HEALTHCARE Co., Ltd. 53, Kunotsubo, Terado-cho, Muko, KYOTO,
617-0002 JAPAN
---|---
EU-representative| I| OMRON HEALTHCARE EUROPE B.V. Scorpius 33,
2132 LR Hoofddorp,THE NETHERLANDSwww.omron-healthcare.com
EC| REP
Production facility| OMRON HEALTHCARE MANUFACTURING VIETNAM CO.,
LTD. No.28 VSIP II, Street 2, Vietnam-Singapore IIndustrial Park II,Binh
Duong Industry-Services-Urban Complex, Hoa Phu Ward, Thu Dau Mot City,Binh
Duong Province,Vietnam
Subsidiaries| OMRON HEALTHCARE UK LTD. Opal Drive, Fox Milne, Milton
Keynes, MK15 ODG UKwww.omron-healthcare.co.uk
OMRON MEDIZINTECHNIK HANDELSGESELLSCHAFT mbH Gottlieb-Daimler-Strasse 10,
68165 Mannheim, GERMANYwww.omron-healthcare.de
OMRON SANTE FRANCE SAS** 14, rue de Lisbonne, 93561 Rosny-sous-Bois Cedex,
FRANCEwww.omron-healthcare.fr
References
- Medical Devices and Healthcare Solutions | OMRON UK
- Medical Devices and Healthcare Solutions - OMRON Healthcare EMEA
- Home | OMRON DE
- Home | OMRON FR
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>