MOUNTUP MU4002-A Single Monitor and Laptop Tray Desk Mount Instruction Manual
- June 17, 2024
- MOUNTUP
Table of Contents
Single Monitor and Laptop Tray Desk Mount
Instruction Manual
MU4002-A Single Monitor and Laptop Tray Desk Mount
WARNING!
If you have any confusion or are not quite sure about the installation, please
do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are
included and undamaged. Improper installation, such as using the product for
monitors over its load capacity or for any purpose not explicitly specified,
may cause damage or serious injury. We would not be liable for any damage or
injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed.
Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION
IS REQUIRED.
PACKAGE CONTENTS
DO NOT EXCEED WEIGHT CAPACITY.
ASSEMBLY STEPS
STEP 1: Clamp Installation OR Grommet Base Installation
OPTION A: Clamp Installation
Mount Clamp (C) to the bottom of Pole (D) by tightening bolts (F) with 5mm
Allen Key (J).
Adjust the Clamp width to fit your desk. Secure stand to the desktop by
tightening Clamp (C).
OPTION B: Grommet Base Installation
If existing grommet hole comes with a plastic protector, remove it to ensure a
flat surface before installing the desk mount.
Detach Bracket (C1) and Bolt Y (C2) from Clamp (C).
Position pole (D) on the mounting surface and then secure it by tightening the plastic knob after making Bolt Y (C2) through the Bracket (C1), desk hole, and the bottom of Pole (D) sequentially.
STEP 2 : Arm Installation
Install wire clip (E) and two swivel arms (B) to the pole (D). Fasten the bolt
with supplied 6mm Allen Key (K). Attach the wire clips (H) to the swivel arm
(B).
STEP 3 : Attach the VESA Plate to the Monitor or Laptop Tray
3-1: Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (A) to the back of monitor and secure it by using a 6 mm
Allen Key (K) to tighten screws (M-A or M-C) along with washers (M-E).
Do not tighten the screws excessively or your monitor might be damaged.
OPTION B: Curved Back Monitor
Attach the VESA plate (A) to the back of monitor and secure it by using a 6 mm
Allen Key (K) to tighten screws (M-B or M-D) along with washers (M-E) and
spacers (M-F).
Do not tighten the screws excessively or your monitor might be damaged.
3-2: Attach Laptop Tray
Install the VESA plate (A) to the laptop tray (L) using 4pcs screws (G) and
4pcs nuts (N) , tighten by 6mm Allen key (K) . Apply pads (M) to the laptop
tray to avoid laptop scratches.
STEP 4 : Hang Monitor and Laptop Tray
Slide the monitor and laptop tray onto the head of swivel arm (B). Install the
security bolt (I).
Make sure the security bolt is installed before you rotate the monitor.
STEP 5 : Secure the Laptop on the Laptop tray
STEP 6: Tilt Adjustment
STEP 7: Cable Management
Manage cables and store Allen Keys (J,K) in wire clip (E) for future use.
Adjust as Desired
Adjust monitor position and rotation.
Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.
Product Dimensions
**** CAUTION AND MAINTENANCE:
- Never allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>