HOLMAN Spray 5L Pump Free Garden Sprayer User Guide

HOLMAN Spray 5L Pump Free Garden Sprayer

Product Specifications

• Minimum tap pressure required to fill tank: 350kPa
• Spray Head includes 4 individual spray functions: JET, CONE, SHOWER, and MIST

Product Usage Instructions

Removing the Grab Handle:

1. Push down on the GRAB HANDLE (M) Twist counter-clockwise to unhook the GRAB HANDLE from the PRESSURE TANK (E)
2. Pull the GRAB HANDLE out of the PRESSURE TANK
3. Place the GRAB HANDLE somewhere clean to avoid dirt touching the lubricated PLUNGER (N)
4. Optional: To include more additives, insert the plunger to push the first shot into the tank
5. Optional: For powder additives, include a cup of water in addition to the additive
6. Repeat Steps 4c and d as necessary to introduce more additive
7. Add fertilizer or other before filling with water

Introducing Spray Additives:

• Ensure the SPRAY HOSE (D) is attached when removing or replacing the GRAB HANDLE to avoid excess additives or water squirting out of the PRESSURE TANK outlet
• After removing the GRAB HANDLE, follow your additive instructions to pour the correct amount into the TANK OPENING (O)
• If using a powder additive, dissolve a cup of it in water first
• Insert the PLUNGER into the TANK OPENING, push down and rotate clockwise to hook the GRAB HANDLE back into place
• Follow Tank Filling in Step 5 to fill the tank with water and mix in the additive

Tank Filling:

1. Once water is flowing out, turn off the tap
2. Locate the 12mm snap-on HOSE CONNECTION (K)
3. Attach the INLET VALVE CONNECTOR (P)
4. Add a standard 12mm garden hose (Q) onto this connection
5. Ensure the INLET VALVE (P) is open and turn the garden hose tap on to begin filling
6. Watch the pressure gauge as the reservoir fills with water, it should move towards the MAX level

Spraying:

• The SPRAY HEAD (A) includes 4 individual spray functions: JET, CONE, SHOWER, and MIST
• Before spraying, twist the orange section of the SPRAY HEAD to select the desired spray pattern
• To begin spraying, point the SPRAY HEAD in the desired direction and pull the orange TRIGGER (C) lever

Frequently Asked Questions (FAQ):

• Why is the pressure gauge reading below 1 bar?
  This is only necessary if the pressure is below 1 bar. It should be able to hold this minimum pressure for an extended period.

• Why is the pressure release valve triggered and spraying water during filling?
  This is perfectly normal and means the tank is full of water.
  Turn off your tap and disconnect your garden hose.

Spray Additives

Removing the Grab Handle

• a. Push down on the GRAB HANDLE (M)
• b. Twist counter-clockwise to unhook the GRAB HANDLE from the PRESSURE TANK (E)
• c. Pull the GRAB HANDLE out of the PRESSURE TANK
• d. Place the GRAB HANDLE somewhere clean to  avoid dirt touching the lubricated PLUNGER (N)
• e. Add fertilizer or other additives to your EzySpray® before filling with water
• f. Optional: To include more additives, insert the plunger to push the first shot into the tank
• g. Optional: For powder additives, include a cup of water in addition to the additive
• h. Repeat Steps 4c and d as necessary to introduce more additive

Introducing Spray Additives

NOTE
Ensure the SPRAY HOSE (D) is attached when removing or replacing the GRAB HANDLE to avoid excess additive or water squirting out of the PRESSURE TANK outlet

• i. After removing the GRAB HANDLE, follow your additive instructions to pour the correct amount into the TANK OPENING (O)
• j. Insert the PLUNGER into the TANK OPENING, in the position shown above, push down and rotate clockwise to hook the GRAB HANDLE back into place
• k. Follow Tank Filling in Step 5 to fill the tank with water and mix in the additive

Tank Filling

NOTE
Min. tap pressure required to fill tank: 350kPa

• a. Before filling your EzySpray®, push excess air from your garden hose by turning on the tap
  This will stop additional air using the EzySpray® capacity

• b. Once water is flowing out, you can turn off the tap

• c. Locate the 12mm snap-on HOSE CONNECTION (K)

• d. Attach the INLET VALVE CONNECTOR (P)

• e. Add a standard 12mm garden hose (Q) onto this connection

• f. Ensure the INLET VALVE (P) is open and turn the garden hose tap on to begin filling
  WARNING
  Watch the pressure gauge as the reservoir fills with water
  The gauge should begin moving towards the MAX level

• g. If your water source is high pressure, it may trigger the PRESSURE RELEASE VALVE (L) when full to stop your EzySpray® from over-pressurizing:

• h. If your water source is low pressure, the EzySpray® will stop filling when it reaches the maximum pressure

• i. Once your EzySpray® is full, turn off your tap and close the INLET VALVE (P)

• j. Disconnect the INLET VALVE (P) and garden hose
  High or low-pressure circumstances are fine and shouldn’t damage your EzySpray®
  WARNING
  Watch for excess water from the hose when disconnecting

Spraying

Spray Functions
The SPRAY HEAD (A)includes 4 individual spray functions: JET, CONE, SHOWER and MIST

• a. Before spraying, twist the orange section of the SPRAY HEAD to select the desired  spray pattern Trigger Action
• b. To begin spraying, simply point the SPRAY HEAD in the desired direction and pull the orange TRIGGER (C) lever

Troubleshooting

Flushing and Cleaning

Spray Functions
It is important to completely flush your EzySpray® with clean water when finished with chemical spraying

• a. After you have completed your spraying job and the tank has run out, connect to a tap and refill the tank with clean water
• b. Point your spray wand into a bucket or anywhere you don’t mind the excess fluid flowing
• c. Hold down the trigger and let the contents flow through until the tank is empty
• d. Once the tank is empty, we recommend storing your EzySpray® in a dry, protected space out of direct sunlight

WARNING
Don’t leave full for extended periods!

www.holmanindustries.com.au/product/18mm-brass-sprinkler-adaptor

We appreciate having you as a customer and would like to say thank you for choosing us. We recommend registering your new product on our website. This will ensure we have a copy of your purchase and will activate an extended warranty. Keep up to date to with relevant product information and special offers available through our newsletter.www.holmanindustries.com.au/product- registration/

Head Office/Service
11 Walters Drive, Osborne Park WA 6017 Tel: +61 8 9416 9999 Fax: +61 8 9416 9920
support@holmanindustries.com.au
www.holmanindustries.com.au
Copyright © 2023 Holman Industries 6

References

• Holman Industries - Irrigation, Garden Lights, Plumbing
• Product Registration and Extended Warranty - Holman Industries
• Holman Industries - Irrigation, Garden Lights, Plumbing
• Product Registration and Extended Warranty - Holman Industries
• ⌀18mm Brass Sprinkler Adaptor - Holman Industries

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>