Streamline 36 in. Amendola Convertible Undermount Range Hood Owner’s Manual
- June 17, 2024
- Streamline
Table of Contents
- Streamline 36 in. Amendola Convertible Undermount Range Hood
- Product Information
- Product Usage Instructions
- Frequently Asked Questions
- Safety Disclaimer
- Electrical Guidelines
- Warranty Guidelines
- Tools Required
- Parts Supplied
- Installation
- 25.
- Product Care & Maintenance
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Streamline 36 in. Amendola Convertible Undermount Range Hood
Product Information
Specifications
- Product Name: Undermount Range Hood Series
- Model Number: [Insert Model Number]
- Manufacturer: Streamline Bath
- Contact Information:
- Website: www.streamlinebath.com
- Email: support@streamlinebath.com
- Phone: 310-935-0028
Product Usage Instructions
1. Safety Disclaimer
Please read the safety disclaimer in the user manual before proceeding with the installation and usage of the range hood.
2. Electrical Guidelines
Before installing the range hood, make sure to comply with the following electrical guidelines:
- Observe all governing codes and ordinances.
- Ensure that the electrical installation meets the latest edition of the National Electrical Code, ANSI/NFPA 70, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91.
- Comply with all local codes and ordinances.
- For a copy of the code standards, contact the National Fire Protection Association or CSA International using the provided contact information.
3. Warranty Guidelines
The range hood comes with a limited manufacturer’s warranty. Please note the following warranty guidelines:
- The warranty does not cover damages caused by improper installation, misuse, or unauthorized repairs.
- Any attempt to alter, modify, or amend the warranty without authorization in writing by an officer of Streamline Bath is not effective.
- For more information on the warranty coverage and limitations, refer to the warranty section in the user manual.
4. Tools Required
Before starting the installation, make sure you have the following tools:
- Electric Drill
- 5/16” Drill Bit
- 5/32” Drill Bit
- Screwdriver
- Utility Knife
- Pliers
- Tape Measure & Pencil
- Electrical Wiring
- Aluminum Foil Tape/Duct Tape
- Hammer
- Jigsaw/Saber Saw
- Stud Finder
5. Parts Supplied
The following parts are included with the range hood:
- Range Hood
- Mounting Screws (4×30 mm)
- 5” Round Aluminum Duct (Length: 6.5 ft.)
- Flaps
- Damper
- Wall Anchors
- Vent Cover
- Charcoal Filter Set
6. Installation Dimensions
Before installing the range hood, take note of the following dimensions:
- A. Floor To Ceiling Height
- B. Floor To Counter Top Height (Standard: 36”)
Frequently Asked Questions
- Q: Where can I find installation and assembly videos?
- A: You can find installation and assembly videos on our website at www.streamlinebath.com or on our YouTube page by searching for Streamline Bath or following this link: Streamline Bath YouTube Channel.
- Q: How do I replace the LED light and install the charcoal filter?
- A: Refer to section 11 of the user manual for detailed instructions on LED light replacement and charcoal filter installation.
UNDERMOUNT RANGE HOOD SERIES
OWNER’S MANUAL & INSTALLATION GUIDE
READ ENTIRE INSTALLATION GUIDE PRIOR TO INSTALLING THE RANGE HOOD
For installation and assembly videos, please visit our website
www.streamlinebath.com OR
our YouTube page by searching for “Streamline Bath” OR
following the below link to our channel: https://www.youtube.com/channel
/UCII7TGMbkwoGSqzo-pGfaJw
3
Safety Disclaimer
· Please note that these installation instructions are intended as general guidelines only. It is recommended to seek advice from a professional installation specialist for the most suitable type of mounting hardware and support system based on the construction of your space. · Use this unit only in the manner intended by Streamline. If you have any questions, please contact Streamline. · The manufacturer cannot be held responsible for failing to comply with safety regulations. · The manufacturer disclaims all liability for any damage that may be directly or indirectly caused to people, things, and animals due to the failure to follow all the instructions provided in this booklet and, above all, the warnings relating to the installation, operation, and maintenance of the appliance. · These warnings have been provided for your safety and the safety of others. As a result, please read them carefully before installing and operating the appliance. · The installation instructions in this manual are intended for qualified installers, service technicians, or people with similar qualified backgrounds. DO NOT attempt to install this appliance yourself. · Only qualified professionals should
proceed with the installation and electrical wiring. All installation and wiring must be done with regard to any and all applicable codes and standards. · It is dangerous to modify or attempt to modify the characteristics of this system. In the event of malfunctions or if repairs are required to the appliance, do not attempt to solve the problems directly. · All electrical wiring must be properly installed, insulated, and grounded. · This product is designed for indoor residential use only. · Local codes may necessitate using a cable-locking connector (NOT provided). Verify local code requirements. · Read all instructions before installing and operating this appliance. This instruction booklet must be kept together with the appliance for future reference. If the appliance is sold or consigned to other parties, please ensure that the booklet is supplied with it to ensure that the new user has the correct information on the operation of the range hood and is aware of the warnings.
4
· Before installing your range hood, it’s essential to verify the local, city, and state regulations for the appropriate venting method. Many agencies have specific CFM (cubic feet per minute) rating specifications for hoods as well. Additionally, you may need to purchase additional items to ensure that the hood is vented in accordance with your local city and state specifications. Be sure to follow all regulations and guidelines to ensure safe and proper installation. · Before operating the product, remove any foams, tapes, and protective films that cover it. Take caution while removing installation components, and use hand gloves to safeguard against sharp edges. · Ducted range hoods must be vented to the outdoors. DO NOT VENT EXHAUST AIR INTO ATTICS, CRAWL SPACES, GARAGES, OR WITHIN WALLS/CEILINGS. · To avoid damage during installation, safeguard the cooktop surface below using plywood or a similar material. · To prevent damage to your range hood, make sure to keep debris from entering the vent opening. This appliance is not intended for use by young children. Young children should be supervised to ensure they do not play with the appliance.
· The range hood must only be used to exhaust cooking fumes in the home. The manufacturer disclaims all liability for any other use of the appliance. The maximum weight of any object placed above the hood (or hung to) must not exceed 3.3 lbs. · This range hood may NOT be used to exhaust hazardous materials · When cutting or drilling in the wall or ceilings, be aware of piping, insulation, electrical wires, and other components that may not be visible. · If the supply cord is damaged, it must be replaced by the manufacturer to avoid a hazard. Any modifications that may be required to the electrical system for installing the range hood must only be made by qualified electricians. DO NOT OPERATE ANY FANS WITH A DAMAGED CORD OR PLUG. · Only plug this unit into a properly grounded outlet. · Always check that the electrical parts are off when the appliance is unused. · Accessible range hood parts may become hot when used with cooking appliances. · Before removing any parts from the range hood, please ensure that you wear protective gloves. The range hood may have very sharp edges.
5
· Before drilling any holes, it is crucial to verify that the space behind the installation surface is free of any electrical cables, pipes, or other obstructions. · The stainless-steel surfaces of the range hood are highly susceptible to damage during installation if they are scratched or bumped by tools. Therefore, it is crucial to take necessary precautions to protect the surfaces while installing the range hood. · It is essential to ensure proper room ventilation when using the range hood in conjunction with gas or other fuel-burning appliances. · Additionally, the range hood should only be installed over a cooktop with a maximum of four burners. Finally, avoid venting the air into a flue that is also used to exhaust fumes from appliances burning gas or other fuels.It’s important to note that range hoods and other cooking fume extractors may impact the safe operation of gas or other fuel- burning appliances, including those in other rooms. This is because of the potential for backflow of combustion gases, which can lead to carbon monoxide poisoning. Therefore, after installing a range hood or other cooking fume extractor, it’s crucial to have a competent person test the operation of flued gas appliances to ensure that there is no backflow of combustion gases. · Please take note of the following
warning to reduce the risk of a range top grease fire: · Never leave surface units unattended when set to high heat. Boil-over can cause smoke and grease to spill over, which may ignite. · Always turn on the range hood when cooking at high heat or with food that produces high flames. · Clean ventilation fans frequently, ensuring that grease does not accumulate on the fan or filter. · Use appropriate pan sizes that match the size of the surface element. Always use cookware that is appropriate for the size of the surface element. · Please take note of the following warning to reduce the risk of injury in the event of a range top grease fire: · Smother the flames with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. Be careful not to get burned. If the flames do not go out immediately, evacuate and call the fire department. · Never pick up a flaming pan, as you may get burned. · Do not use water, including wet dishcloths or towels, as this can result in a violent steam explosion. · Use an extinguisher ONLY if you know you have a class ABC extinguisher and know how to operate it; the fire is small and contained, the fire department is being called, and you can fight the fire with your back to an exit.
6
· Sufficient air is needed for proper combustion and exhaustion of gases to avoid back-drafting. Follow the heating equipment manufacturer’s guidelines and safety standards, such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and local municipal code guidelines. · Do not connect the appliance to flues (from boilers, fireplaces, etc.). Make sure the mains voltage corresponds to the values on the rating plate located inside the range hood. · Old ductwork should be cleaned or replaced before installation to avoid the possibility of a grease fire. · To ensure the installation process is carried out safely and without causing harm to the product or oneself, it is necessary for two individuals to participate in the installation of range hoods due to their weight and size. · Before performing any cleaning or maintenance operations, disconnect
the range hood by unplugging it or using the main switch. · Ensure that there is adequate ventilation in the room when the range hood is used at the same time as appliances burning gas or other flues. · The exhaust air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. · Before servicing or cleaning the range hood, make sure to turn the power off. · Repairs performed by unqualified persons may cause damage. For all questions on repairs and other work on the appliance, please contact Streamline at 310-935-0028 or support@streamlinebath.com
Electrical Guidelines
Please ensure to observe all governing codes and ordinances when installing
the range hood. Additionally, ensure that the electrical installation is
adequate and complies with the latest edition of the National Electrical Code,
ANSI/NFPA 70, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91, as well as all local codes and ordinances.
For a copy of the above code standards, you can contact the National Fire
Protection Association at: 1 Batterymarch Park, Quincy, MA 02169-7471 or CSA
International at 8501 East Pleasant Valley Road, Cleveland, OH 44131-5575.
8
Warranty Guidelines
LIMITED WARRANTY EXCLUSION
ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
STREAMLINE® IS NOT LIABLE FOR ANY INDIRECT, PUNITIVE, INCIDENTAL,
CONSEQUENTIAL, SPECIAL OR SIMILAR DAMAGES INCLUDING, BUT NOT LIMITED TO, TIME
AWAY FROM WORK, HOTELS AND/OR RESTAURANT MEALS, REMODELLING EXPENSES IN EXCESS
OF DIRECT DAMAGES WHICH ARE DEFINITIVELY CAUSED EXCLUSIVELY BY STREAMLINE®,
LOST PROFITS OR REVENUE, INABILITY TO USE THE PRODUCT, OR ANY OTHER ASSOCIATED
EQUIPMENT, THE COST OF SUBSTITUTE
EQUIPMENT, AND ANY CLAIMS BY THIRD PARTIES RESULTING FROM THE USE OF THIS
PRODUCT.
UNDER NO CIRCUMSTANCES SHALL STREAMLINE’S LIABILITY EXCEED THE PURCHASE PRICE
OF THE UNIT.
STREAMLINE® PRODUCTS MUST BE INSTALLED BY A FULLY INSURED, LICENSED,
PROFESSIONAL WHO SHALL FOLLOW THE INSTRUCTIONS PROVIDED BY STREAMLINE®. SHOULD
THE PRODUCT BE INSTALLED BY AN INDIVIDUAL WHO IS NOT A FULLY INSURED, LICENSED
PROFESSIONAL, THIS
SHALL VOID THE WARRANTY OF THE PRODUCT.
SHOULD A WARRANTY CLAIM ARISE AND EITHER PARTS, REPLACEMENT, OR REPAIR OF THE
STREAMLINE PRODUCT IS NECESSARY, FULFILLING THE INITIAL WARRANTY CLAIM SHALL
DISCHARGE STREAMLINE® OF ANY FUTURE WARRANTY OBLIGATION. IF THE PURCHASER
REFUSES THE WARRANTY SOLUTION PROVIDED BY STREAMLINE®, THIS ACT SHALL VOID THE
WARRANTY. UNDER BOTH INSTANCES, STREAMLINE® WILL NOT BE HELD RESPONSIBLE FOR
ANY COSTS
ASSOCIATED WITH SERVICING THE WARRANTY
NO PERSON MAY MAKE ANY REPRESENTATION, AFFIRMATION, OR WARRANTY OTHER THAN
THOSE CONTAINED IN THIS WARRANTY. ANY AFFIRMATION, REPRESENTATION OR WARRANTY
BY ANY PERSON WHO IS NOT A STREAMLINE® EMPLOYEE SHALL NOT BE ENFORCEABLE
AGAINST
STREAMLINE®
Streamline® makes no representations about the quality, durability, or need for service or repair of its products other than the representations contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this product, you should ask Streamline® or your retailer about buying an extended warranty. This warranty gives you specific legal rights, and you may have other rights that vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, and some states do not allow limitations on how long an implied warranty lasts, so the limitations or exclusions stated above may not apply and may vary from state to state.
The warranties stated herein apply only to the first purchaser of the Product
and are not transferable. Streamline® reserves the right to request proof of
purchase at the time any warranty claim is submitted to confirm that the
Product falls within the scope of this limited product warranty.
OUT OF WARRANTY PRODUCT
STREAMLINE® IS UNDER NO OBLIGATION, AT LAW OR OTHERWISE, TO PROVIDE YOU WITH
ANY CONCESSIONS, INCLUDING REPAIRS, PRORATES,
LIMITED MANUFACTURER’S WARRANTY
All parts and finishes of Streamline® products are warranted to the original
consumer purchaser to be free from defects in material and workmanship for a
period of two to five years [depending on the product and model; please check
the product listing or email us at
support@streamlinebath.com if you are
unsure] after the date of original retail purchase. Proof of the original
purchase is required to obtain a remedy under this limited warranty.
Streamline® recommends using a certified professional for all installation and
repair of kitchen and bathroom fixtures.
Streamline® will replace, free of charge, during the warranty period any part
or finish that proves defective in material and/or workmanship under normal
installation, use and service. Replacement parts may be obtained by emailing
us at support@streamlinebath.com
This warranty is extensive in that it covers replacement of all defective
parts and even finish, but these are the only two things that are covered.
Labor charges and/or damage incurred in installation, repair, or replacement
as well as any other kind of loss or damages are excluded. Proof of purchase
(original sales receipt) from the original consumer purchaser must be made
available to Streamline® for all warranty claims. This is the exclusive
warranty by Streamline®, which does not make any other warranty of any kind,
including the implied warranty of merchantability. This warranty excludes all
industrial, commercial and business usage, whose purchasers are hereby
extended a one-year limited warranty from the date of purchase, with all other
terms of this warranty applying except the duration of the warranty.
9
WHAT IS NOT COVERED UNDER THIS LIMITED WARRANTY
· Normal wear and tear, spills of food, liquid, grease accumulations or
cosmetic damage.
· Damage due to accidents, misuse, physical force, improper installation or
operation, mishandling, neglect, fire, heat, water, humidity, liquids, insect
infestation, or other intrusion.
· Products that have been repaired, altered or modified by anyone other than
Streamline® or its authorized service representative.
· Damage caused by use of non-Streamline® accessories or misapplication.
· Products whose serial numbers have been removed, altered or rendered
illegible.
· Products purchased, shipped from, used or serviced outside the United
States, Canada, and Mexico.
· Damage caused by acts of nature such as, but not limited to, lightning
damage.
· Products returned without valid proof of purchase.
· Consumable parts such as light bulbs, metal, and charcoal filters.
· Any party’s willful misconduct, negligence, misuse, abuse, accidents,
neglect, improper operation, failure to maintain, improper or negligent
installation, tampering, failure to follow operating instructions,
mishandling, unauthorized service (including self-performed “fixing” or
exploration of the product’s internal workings).
· Use of corrosive or abrasive cleaning products.
· Cosmetic damages including scratches, dents, chips and other damage, unless
such damage results from defects in materials and workmanship and is reported
to Streamline within 3 calendar days of delivery.
· Use of the Product in anything other than its normal, customary and intended
manner.
· A failure to comply with any applicable state, local, city or county
electrical, plumbing and/or building codes, regulations, or laws, including
failure to install the product in strict conformity with local fire and
building codes and regulations.
· In no event shall Streamline have any liability or responsibility whatsoever
for damage to surrounding property, including cabinetry, floors, ceilings, and
other structures or objects around the product.
NO ATTEMPT TO ALTER, MODIFY, OR AMEND THIS WARRANTY SHALL BE EFFECTIVE UNLESS
AUTHORIZED IN WRITING BY AN
OFFICER OF STREAMLINE.
10
Tools Required
Electric Drill
5/16” Drill Bit
5/32” Drill Bit
Screwdriver
Utility Knife
Pliers
Tape Measure & Pencil
Electrical Wiring
Aluminum Foil Tape/Duct Tape
Hammer
Jigsaw/Saber Saw
ON OFF
Stud Finder
11
Parts Supplied
Range Hood
Name
Image
Qty
4×30 mm Mounting Screws
x 9
5” Round
Aluminum Duct
x 1
(Length: 6.5 ft.)
Flaps
x 1
Damper
x 1
Wall Anchors
x 9
Vent Cover
x 1
Charcoal Filter Set
x 1
streamlinebath.com
support@streamlinebath.com
12
Installation
Dimensions
A
Floor To Ceiling Height
B
Floor To Counter Top Height (Standard: 36”)
C
Height of Counter Top to Range Hood Bottom (Minimum 26”-30”)
D
Kitchen Cabinet Height
E
Range Hood Installation Height [A-D-(B+C)]
D E
C
B
C AA
B
13
Ventilation Options
There are three different options available for venting the range hood. It is recommended to seek guidance from a professional installer to choose the best installation method for your specific requirements.
Ductless
Wall Venting
Roof Venting
streamlinebath.com
support@streamlinebath.com
14
· We recommend installing the vent system before installing the range hood. · A damper is required in the venting system. If the wall or roof cap already has a damper, do not use the damper that comes with the range hood. · Ensure that the exhaust hose is fully extended to maximize airflow. · For the best results, it is advised to limit the length of the exhaust duct hose and the number of bends in the system to achieve optimal performance. · The ideal length of the duct system is between 35 and 40 feet. · Make sure there is enough clearance within the ceiling or wall for the exhaust vent before making any cutouts. · Only use metal ducting, with rigid metal ducting being the preferred option. Avoid using plastic or metal foil ducting. · If the diameter of the exhaust ducting is less than 4.9” (12.5cm) or if flat ducting is used, the range hood’s noise level may increase and the exhaust efficiency may be reduced. · To ensure that all joints in the ductwork are appropriately connected, carefully inspect each joint. Use certified aluminum or foil tape to seal and tape all joints securely. Clamps may also be used. · To minimize the backward flow of cold air and prevent the conduction of outside temperatures, it is advisable to add an additional
backdraft damper and thermal break in the duct system. The damper must be placed on the cold air side of the thermal break, which should be installed as close as possible to where the duct system enters the heated portion of the house. · Avoid using a 4” laundry wall cap. · Attach the end of the exhaust hose to a vent leading outside of the home. Avoid ventilating the range hood into an attic or other closed area to prevent the buildup of harmful fumes and to ensure proper ventilation. · Do not use more than three 90degree elbows not to affect range hood performance. · The size of the vent openings should be consistent. · It is permissible to install a 90degree elbow directly above the range hood. · If multiple elbows are used, ensure there is at least 24 in. of straight duct between them. · Do NOT install two elbows together. · You may use caulking to seal the exterior walls or roof openings around the vent cap. · A 90-degree elbow may be needed to vent through a wall.
streamlinebath.com
support@streamlinebath.com
15
8. Installation Instructions
1. The range hood should be carefully removed from its packaging.
RANGE HOOD
2. Remove the protective blue/white film from the range hood.
3. Ensure that there are no components or packaging materials that may have become trapped or left inside the range hood and remove any, if necessary.
streamlinebath.com
support@streamlinebath.com
16 4. Test to ensure that the range hood works by plugging it into an
electrical outlet.
5. Check that all features are properly functioning and that the LED lights
work.
6. Unplug the range hood.
7. Remove the mesh or baffle filters, depending on the range hood that was
purchased.
17
8. On the top right of the motor, there is a lever that you can use to switch
between recirculating and ducted modes for the range hood. Loosen the lever
from its current position and adjust it to the desired position. · For ducted
mode, turn the lever to the RIGHT. · For ductless/recirculating mode, turn the
lever to the LEFT.
Recessed Installation
9. If you plan to use the provided template, affix the template with tape to
the bottom of the cabinet. Use a pencil to trace and mark the spots on the
bottom of the cabinet where drilling will occur for the mounting holes as well
as for the duct.
Alternatively, you may also position the range hood underneath the cabinet and
mark the location of the mounting holes on the cabinet as well as the duct
cutout.
streamlinebath.com
support@streamlinebath.com
18 10. Use a 5/16” [8mm] drill bit to make (4) pilot holes in the cabinet at
the
marked locations. For wood, use a 5/32” drill bit.
Drill
11. Insert the plastic wall anchors firmly into the four drilled holes.
Plastic Anchors
19 12. Insert the ST4*30 screws into the plastic wall anchors, leaving about
1/4
of an inch of the screw protruding from the cabinet. It will be tightened
after the range hood is hung in the final step.
Screws
13. Check for stability by mounting the range hood onto the screws and
ensuring it fits tightly and securely.
14. Remove the range hood from the mounting screws.
streamlinebath.com
support@streamlinebath.com
20
15. There are multiple ventilation choices available for the range hood:
A
B
C
Venting through the roof:
If you choose to vent through the roof, you will
need to make an extra cutout of 5.25”(133mm) to accommodate the duct
passing through the ceiling.
Venting through the wall:
When venting through the wall, an extra cutout of 5.25” (133mm) will need to
be made
to allow for the duct to be properly connected outside.
Ductless Ventilation:
No additional ductwork is required for a ductless installation. The air will
circulate through the range hood and exit out into the
kitchen.
Cabinet top cutout (A)
5.25”
(13.3cm)
Cutout
Centerline
Wall/side cutout (B)
Centerline
5.25”
Cutout (13.3cm)
streamlinebath.com
support@streamlinebath.com
21 If installing using the ducted installation method, please follow the below
steps. If using the ductless installation method, PLEASE SKIP
and move to step #23. 16. Two holes need to be cut in the cabinet: one for the
duct and another
for the power cord. Use a saw or drill to create a circular hole in the bottom
of the cabinet with a diameter of 5.25 inches. Drill a 1-1/2 inch hole into
the bottom of the cabinet next to the vent hole to create an access hole for
the power cord. Remove any tape that may be on the duct.
Electric Jigsaw
17. Take the provided damper and insert it into the top of the range hood
duct. Rotate clockwise to tighten in place.
Damper
22 18. Attach the vent flaps in the exhaust port on the top of the range hood.
Ensure that the flaps can open smoothly without any obstructions. Ensure that
the bumps on the flap face upwards and outwards.
Flaps
19. Connect the 5” round aluminum duct exhaust hose to the round vent air
flap by placing one end of the hose over the flap and securing it with two
small screws. Then, wrap the connection with tape or use a hose
clamp and wrap it with tape to ensure a tight seal.
Exhaust Hose
Small Screws
Tape
Some under-mount range hood models may have a rectangular side vent cutout
designed for side ventilation. Please check the specification
sheet of the range hood or contact our customer service to confirm.
streamlinebath.com
support@streamlinebath.com
23 Side Vent Installation 20. If choosing to vent from the side, remove the
backplate from the range hood. Using pliers, disassemble the metal panel by
pulling it from left to right. Then, use the pliers to tear away the seal by
pulling it outward.
Pliers
21. Attach the square to round outlet damper (NOT INCLUDED IN PURCHASE) or
rectangular damper (NOT INCLUDED IN PURCHASE).
Square To Round Outlet Adaptor
Rectangular Duct
22. Take the provided vent cover and place it on top of the venting cutout.
Rotate clockwise to tighten in place.
Vent Cover
24 23. Pull the ductwork and electrical cord through the cabinet hole.
If installing using the ductless installation method, please follow the below
step. If using the ducted installation method, PLEASE SKIP and move to step
25.
24. Take the provided vent cover and place it on top of the range hood
venting cutout. Rotate clockwise to tighten in place.
Vent Cover
25. Lift and hang the range hood on the screws previously drilled.
25
26. At the back of the range hood, right below the mounting holes, there will
be 2 visible holes (1 on each side). These are additional safety holes to help
secure the range hood in position.
1. Use a 5/16” [8mm] drill bit to make pilot holes in the cabinet at the
marked locations. For wood, use a 5/32” drill bit.
2. Fasten the range hood using (2) ST4*30 screws. 3. Tighten the four initial
mounting screws that you drilled into the
cabinet.
Drill
1
2
3
27. For ductless installation ONLY: Attach the provided charcoal filters onto
the range hood motor. For detailed instructions on how to insert the charcoal
filters, please see Section 11 on page #45.
28. Re-insert either the mesh or baffle filters into the range hood.
streamlinebath.com
support@streamlinebath.com
26 29. Plug in the range hood to the electrical outlet. Make sure that all
operations are functioning properly.
Wall Installation 1. Find the optimal height for mounting the range hood. For
the best
results, it is recommended to place it between 26 to 30 inches above the
range. Once the ideal mounting height is determined, create a marking at a
horizontal level. This will be for the bottom of the range hood. Locate the
vertical centerline on the wall in reference to the horizontal line, marking
the position where the range hood will be mounted. This line will reflect the
center point.
27
2. If you plan to use the provided template, affix the template with tape to
the wall, making sure that it aligns with the two previously drawn lines.
Alternatively, you may also position the range hood along the vertical and
horizontal lines and mark the location of the mounting holes on the wall.
3. Use a 5/16” [8mm] drill bit to make (2) pilot holes in the wall at the marked locations. For wood, use a 5/32” drill bit.
4. Insert the plastic wall anchors firmly into the drilled holes.
Plastic Anchors
streamlinebath.com
support@streamlinebath.com
28 5. Insert (2) ST4*30 screws into the plastic wall anchors, leaving about
1/4
inch of the screw protruding from the cabinet. It will be tightened after the
range hood is hung.
Screws
6. Check for stability by mounting the range hood onto the screws and
ensuring it fits tightly and securely.
7. Remove the range hood from the mounting screws.
29 If installing using the ducted installation method, please follow the below
steps. If using the ductless installation method, PLEASE SKIP
and move to step #13.
8. Take the provided damper and insert it into the top of the range hood
venting cutout. Rotate clockwise to tighten in place.
Damper
streamlinebath.com
support@streamlinebath.com
30 9. There are multiple ventilation choices available for the range hood:
A
B
C
Venting through the roof:
If you choose to vent through the roof, you will
need to make an extra cutout of 5.25”(133mm) to accommodate the duct
passing through the ceiling.
Venting through the wall:
When venting through the wall, an extra cutout of 5.25” (133mm) will need to
be made
to allow for the duct to be properly connected outside.
Ductless Ventilation:
No additional ductwork is required for a ductless installation. The air will
circulate through the range hood and exit out into the
kitchen.
31 10. Attach the vent flaps in the exhaust port on the top of the range hood.
Ensure that the flaps can open smoothly without any obstructions. Ensure that
the bumps on the flap face upwards and outwards.
Flaps
Some under-mount range hood models may have a rectangular side vent cutout
designed for side ventilation. Please check the specification
sheet of the range hood or contact our customer service to confirm.
streamlinebath.com
support@streamlinebath.com
32
Side Vent Installation 11. If choosing to vent from the side, remove the
backplate from the range
hood. Using pliers, disassemble the metal panel by pulling it from left to
right. Then, use the pliers to tear away the seal by pulling it outward.
Pliers
12. Attach the square to round outlet damper (NOT INCLUDED IN PURCHASE) or
rectangular damper (NOT INCLUDED IN PURCHASE).
Square To Round Outlet Adaptor
Rectangular Duct
13. Take the provided vent cover and place it on top of the venting cutout.
Rotate clockwise to tighten in place.
Vent Cover
33 If installing using the ductless installation method, please follow the
below steps. If using the ducted installation method, PLEASE SKIP and move to
step #8.
14. Take the provided damper and insert it into the top of the range hood
venting cutout. Rotate clockwise to tighten in place.
Vent Cover
15. Lift and hang the range hood on the previously drilled screws.
streamlinebath.com
support@streamlinebath.com
34
16. At the back of the range hood, right below the mounting holes, there will
be 2 visible holes (1 on each side). These are additional safety holes to help
secure the range hood in position.
1. Use a 5/16” [8mm] drill bit to make pilot holes in the cabinet at the
marked locations. For wood, use a 5/32” drill bit.
2. Fasten the range hood using (2) ST4*30 screws. 3. Tighten the four initial
mounting screws that you drilled into the
cabinet.
Drill
1
2
3
17. For ductless installation ONLY: Attach the provided charcoal filters onto
the range hood motor. For detailed instructions on how to insert the charcoal
filters, please see Section 11 on page #45.
18. Re-insert either the mesh or baffle filters into the range hood.
streamlinebath.com
support@streamlinebath.com
35
19. Plug in the range hood to the electrical outlet. Make sure that all
operations are functioning properly.
streamlinebath.com
support@streamlinebath.com
36
9. Control Panel Operation
Push Button
0
1
2
3
0
OFF Button
Turns off the fan.
1
Low Speed Button
Starts the fan at low speed.
2
Medium Speed Button
Starts the fan at medium speed.
3
High Speed Button
Starts the fan at high speed.
Light Button
Used for turning the light on or off.
· To turn the range hood on, simply push the selected speed button (1,2,3). · To turn the range hood off, push the 0 button. · To turn the light on/off, press the LIGHT button. The LIGHT button works without having to push the ON/OFF button for the range hood.
2367 Electronic Push Button
Light Button
Used for turning the light on or off.
High Speed Button
Starts the fan at high speed.
Medium Speed Button
Starts the fan at medium speed.
Low Speed Button
Starts the fan at low speed.
OFF Button
Turns off the fan.
· To turn the range hood on, simply push the selected speed button. · To turn
the range hood off, push the OFF button.
· Pushing the OFF button once delays the turn off time by 1 minute. · Pushing
the OFF button twice turns it off immediately. · To turn the light on/off,
press the LIGHT button. The LIGHT button works without having to push the
ON/OFF button for the range hood.
streamlinebath.com
support@streamlinebath.com
38 Electronic Touch Panel
88:88
Light Button
Used for turning the light on or off.
Timer
Allows for a delayed shutdown of the range hood.
Speed Button
Changes the speed of the motor from high, medium, and low levels.
ON/OFF Button
Turns the fan on or off.
39
Electronic Touch Panel
· To turn the range hood on, press the ON/OFF button. · To turn the range hood
off, push the ON/OFF button.
· Pressing the OFF button once delays the turn-off time by 1 minute.
· Pressing the OFF button again will turn the range hood off immediately.
· To turn the light on/off, press the LIGHT button. The LIGHT button works
without having to push the ON/OFF button for the range hood.
Selecting A Speed
· To select the range hood speed, press the SPEED button. · F3- Highest Speed
Setting · F2- Medium Speed Setting · F1- Lowest Speed Setting · Pressing the
SPEED button a fourth time will display the clock.
Setting the Clock
· Hold the TIMER button until the display begins to blink. · Once the display
starts to blink, press the SPEED button to cycle through and adjust the hour
setting. · Press the LIGHT button to cycle through and adjust the minute
setting. · Once done, press the TIMER button to complete the changes. · Please
note that the time setting only displays in a 12-hour format. It cannot
display in a 24-hour format.
Delayed Shutdown
· Once the range hood is ON and the fan is operational, press the TIMER
button. · The default delayed shutdown time is 3 minutes. · To change the
delay time, simply continue holding the TIMER button and adjust the time as
necessary (Between 1-60 minutes). · After 10 seconds, the clock will blink,
and the countdown will begin automatically. Once the countdown is complete,
the range hood will automatically turn off. · Please note that the previously
set delay time will reset after shutdown to the standard 3 minutes.
streamlinebath.com
support@streamlinebath.com
40
Product Care & Maintenance
streamlinebath.com
support@streamlinebath.com
41
streamlinebath.com
support@streamlinebath.com
42
43
CHARCOAL FILTERS:
streamlinebath.com
support@streamlinebath.com
44
11. LED Light & Charcoal Filter Replacement
LED LIGHT REPLACEMENT 1. Before proceeding, ensure that the range hood is
turned off and
disconnected from any electrical supply.
2. Remove the mesh or baffle filters, depending on the range hood that was
purchased.
45 3. The electrical wire for the LED lights can be found behind the light
fixtures.
4. The wires for the LED lights are connected using a snap-down connector. To
disconnect the LED lights, press down on the connector and gently pull the
opposing electrical wire away from the connector.
5. Take out the LED light by pressing the long silver bar that covers the
LED. · Push the LED outwards and downwards.
streamlinebath.com
support@streamlinebath.com
46 6. Insert the new LED lights into the opening inwards and upwards and
apply gentle pressure until you hear a click and feel the light sitting
securely in place.
7. Reconnect the electrical wiring in the range hood with the LED snap
connector.
8. Test to make sure that the lights are working properly.
streamlinebath.com
support@streamlinebath.com
47 9. Place the filters back into their original position.
9. Turn the range hood back on.
01 23
48 CHARCOAL FILTER INSTALLATION AND REPLACEMENT 1. Remove the mesh or baffle
filters, depending on the range hood that was purchased.
2. The placement of the charcoal filter varies depending on the model. In
some models that only require 1 charcoal filter, the opening is in the middle
of the motor. For models that require 2 charcoal filters, the openings are
positioned on the sides of the motor. If you have any inquiries regarding the
specific model that you have purchased, please don’t hesitate to contact our
support team.
streamlinebath.com
support@streamlinebath.com
49 3. Take one filter and attach it to the motor. Rotate and twist it
clockwise
until it locks in place. If your range hood model calls for two filters to be
installed, then the filters should be installed on each side. Repeat the
previous step by taking another charcoal filter and attaching it to the other
side of the motor. Rotate and twist it clockwise until it locks in place.
Left Filter
Right Filter
4. To replace the filter, rotate it counterclockwise and then remove it.
After that, install the new charcoal filter and twist it clockwise to lock it
in place.
5. Ensure that the charcoal filter is correctly locked in place to prevent any abnormal noise or potential danger.
References
- Streamline | Kitchen and Bathroom | Bathtubs, Vanity Tops
- Streamline | Kitchen and Bathroom | Bathtubs, Vanity Tops
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>