JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves User Manual

June 17, 2024
JOY

JOY Logo USER MANUAL
Sit and Stand Desk Assembly Instruction

B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage
Shelves

Desk top Dimensions: 120x63cm
3 Height Position Memory
Vertical Range: 72-118cm

![JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY.SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

COMPONENT LIST

![JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

HARDWARE LIST

![JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

INSTALLATION

![JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

![JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

![JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

![JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

![JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

![JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

![JOY B09C6B7NNM Height Adjustable Electric Standing Desk with Storage Shelves

Using the Controller

| Short-press the  button, and the display will flash. Press the  , ,or button to save the current height setting to that button.
---|---
| Press the   button, and the desk will move to the height that was previously set for that button.
| Press the  button, and the desk will move to the height that was previously set for that button.
| Press the button, and the desk will move to the height that was previously set for that button.
| Press the button to raise the desk continuously until it reaches the highest position of 46.5″ (118cm) or the button is released.
| Press the  button to lower the desk continuously until it reaches the lowest position of 28.3” (72cm) or the button is released.

Settings


Change Display Height Units| Press and hold the button until a flashing ‘is displayed. Press  again, and Un is displayed. Press to select it, press or to switch between’IN'(imperial) and SI’ (metric), and press to save your choice.
Change Collision Detection Sensitivity| Press and hold the button until a flashing is displayed. Press  again, and’ is displayed. Press or to switch to ‘and press  to select it. Press or  to switch between off, low, normal, and high sensitivity. Press to save your choice.
Reset| Press and hold the button for 5 seconds, and the screen will show ‘RES. Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot| Overheating Protection: When the motor has been working continuously for 5 minutes, it will stop operating to prevent damage from overheating. Wait for at least 15 minutes before making any further height adjustment.
---|---
E10| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.

E20

| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E60| Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.
–| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

JOY Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals