AIGOSTAR 8433325503031 Fan Heater Instructions

INSTRUCTION
FAN HEATER MODEL: 8433325503031

IMPORTANT SAFEGUARDS

1. Warning: In order to avoid overheating, do not cover the heater.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
3. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
4. The heater must not be located immediately below a socket-outlet.
5. Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
6.  Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
7.   CAUTION — Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
8. Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle
   it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased.
   They can take this product for environmental safe recycling.
   WARNING: IN ORDER TO AVOID OVERHEATING, DO NOT COVER THE HEATER.

PART FIGURE

OPERATING INSTRUCTION

Check before turning on the machine

1. Check if the power wire is under good condition.
2. The product adopts 220-240V AC power supply, before use, please confirm if the rated current of the power socket meets the local requirements with safe grounding device, otherwise, please replace it with the qualified socket.

Put the machine on the flat place
Uneven place may possibly cause the turnover switch at abnormal position, then the heater can’t work after turning on, therefore, please put the heater on the flat place, at least the surface below the base of the heater must be flat.
Temperature Control Knob
Insert the plug into the power socket, then turn the Temperature Control knob clockwise, when hearing the “poop” sound (it means the temperature controller is on), adjust the Temperature Control knob to the desired temperature level.
Power Selection Knob
Turn the Power selection knob to select between 3 functions: Fan only,Low 1200W (LOW), High 2000W(HIGH).
Turn off the Heater
A. Turn the Power selection knob to OFF position.
B. Turn the Temperature Control knob anticlockwise to the initial position.
C. Remove the power plug, store the heater after the entire machine has become cool.
Safety Protection

1. Overheat protection: When the temperature in the heater is too high due to abnormality in the use environment or improper use, the thermostat device can automatically cut off the power and the heater stops working. After the whole heater is cooling, the heater can return to the normal use after removing the abnormality.
2.  Inversion protection: When the whole heater is inverted, the safety system will automatically cut off the power, and return to the work state before inversion after the body is placed upright.

SAFETY CONTROL
Your heater is fitted with a safety device “Double Protector” that (1) switches off the heater by thermal cut-off in the event of overheating or malfunction, It will reset while the temperature reduce to a normal level. (2) Shuts off the heater by thermal fuse in the event of overheating or malfunction and not operates by some other accidental reason.
If overheating or malfunctions continue, return the heater to an Approved Service Agent for examination.
The most common cause of overheating is deposits of dust or fluff entering the heater, Ensure these deposits are removed regularly by unplugging the unit and vacuum cleaning air vents and front grille.
PILOT LIGHT
This fan heater is equipped with a pilot light that glows whenever the heater is plugged in and turned on.
It will continue to glow even if the thermostat has cycled the heating elements off. This feature is to prevent you from being unaware that the heater is operating and maintaining the temperature of the room.
When you do not wish the heater to control the room temperature, turn the control switch to O (off ) and remove the plug from the electrical outlet.

CLEANING AND MAINTENANCE

1. Light accumulated dust may be removed from the heater with a soft cloth. Wipe the exterior surfaces of the heater occasionally with a cloth moistened (not dripping wet) with a solution of mild detergent and water. Dry the case thoroughly with a soft dry cloth before operating the heater.
2.  The fan motor is lubricated by the factory, and will require no further lubrication.
3.  No other user maintenance is required or recommended. If service is required, send your heater to the nearest authorized service depot.
4.  Store heater in a clean and dry place when not in use.

REMEMBER – portable electric heaters are designed for spot heating, or as a supplementary heat source.
They are not intended to be main sources of heat during the normal heating season.
Note: There may be trace of smoke or odour when unit is first operated. Do not be alarmed. This indicates that a drop of oil fell on the heating coil during the manufacturing process. It will quickly evaporate, and should not re-occur.

Troubleshooting

If the product does not operate or does not operate properly, first check according to the following list. If the reason the product does not operate or does not operate properly is not included in the following list, the product mayhave failed. At this time, it is recommended to send the product to the dealer or the Media Service Center for treatment.

After the power is engaged, the power indicator light does not illuminate and the machine does not work.| The plug may not be plugged well.| Check whether the plug is properly inserted into the receptacle.
The temperature control knob is not turned in place.| Check whether the temperature control knob is tumed to the ON position.
The machine suddenly stops during heating.| The temperature exceeds the threshold of the thermal
cut-OFF.| Cool the machine before use.

READ AND SAVE THESE INSTRUCTIONS
WARRANTY: 2YEARS

http://weixin.qq.com/r/9kxKUrTEA_l8rfAx9xnk
AIGOTECH ONSYNK, S.L.
C/LOS TRANSPORTISTAS N.43 NUMANCIA
DE LA SAGRA 45230, TOLEDO, ESPANA
C.LF.: B-85712198
http://WWW.AIGOSTAR.COM
MADE IN P.R.C

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>