DYNOJET PC6-22001 Power Commander 6 Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
POWER COMMANDER 6
for: PC6-22001
Model Coverage: 2003-2005 Yamaha R6
2006-2009 Yamaha R6S
Installation Guide
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS| 2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
---|---
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can
switch on the fl y between these two base maps when you hook up a switch to the
MAP inputs. You can use any open/close type switch. The polarity of the wires
is not important.
Shifter
(Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert the wires
from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of
the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal side
of the sensor and run a wire into this input. This will allow you to calculate
gear position in the Control Center Software. Once gear position is set up you
can alter your map based on gear position and setup gear-dependent kill times
when using a quick shifter.
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your fuel curve based on this input in the
Power Core software.
Launch
You can connect a wire to either Input 1 or Input 2 and then the other end to
a switch. This switch when engaged (continuity) will only allow the RPM to be
raised to a certain limit (set in the software). When released, you will have
full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tightens the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
2003-2005 YAMAHA R6/2006-2009 YAMAHA R6S
INSTALLING THE POWER COMMANDER 6
-
Remove the main seat and the passenger seat.
-
Prop the front of the fuel tank up.
-
Remove the rubber plug in the tail section near the tool kit.
-
Lay the PC6 unit in the tail section and route the harness through the hole and down the right side of the bike.
-
Route the PC6 harness under the cross member for the sub-frame.
-
Attach the ground wire of the PC6 to the negative side of the battery.
-
Unplug the two different 6-pin connectors from the throttle bodies.
One plug is BLACK and the other is CLEAR. -
Plug the PC6 connectors in line with the throttle bodies and main wiring harness. Plug the colored connectors from the PC6 into the matching stock connectors.
-
Secure the PC6 unit in the tail section using the supplied Velcro.
Make sure to clean both surfaces with the alcohol swab before attaching. -
Bolt the fuel tank back into place and reinstall the seats.
Download the latest map fi les from our website at dynojet.com/tunes.
Optional Inputs:
Speed – PINK wire of 3-pin speed sensor connector directly on top of the
engine case. This connector has PINK, ORANGE, and BLACK/WHITE wires. Engine
Temp – GREEN/WHITE wire of BLACK 6-pin connectors (connected to PCV).
12v source for Autotune – BLUE wire of the tail light connector.
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
800-992-4993
DYNOJET.COM
© 2003-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
Documents / Resources
|
DYNOJET PC6-22001 Power Commander
6
[pdf] Installation Guide
PC6-22001, Power Commander 6, PC6-22001 Power Commander 6, 2003-2005 Yamaha
R6, 2006-2009 Yamaha R6S
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>