anko 42956457 Wooden Cot In Oak Colour Instruction Manual

June 17, 2024
Anko

anko 42956457 Wooden Cot In Oak Colour

anko-42956457-Wooden-Cot-In-Oak-Colour-product

Product Information

  • Product Name: Wooden Cot in Oak Colour
  • Manufacturer: Unknown
  • Recommended Mattress Size: 690mm wide x 1300mm long and no more than 150mm thick

Maximum Weight Capacity: 18kgs

Specifications

  • Supplied loose in box
  • Material: Wood
  • Color: Oak
  • Assembly Required: Yes
  • Base Height: Adjustable
  • Mattress Base Positions: Low and High

Product Usage Instructions

Assembly

  1. Read the instruction manual carefully before starting the assembly process.
  2. Ensure all parts and hardware are present and in good condition.
  3. Identify the labeled parts: A, B, C, D, E, F, G, H, I, J, K, L.
  4. Pre-assemble part L with four M6*15mm screws.
  5. Attach parts A, B, C, D, E, F, G, H, I using the provided screws as indicated in the manual.
  6. Do not firmly tighten bolts/screws. Pre-drilled holes should face inside.
  7. Secure part I with two M6*55mm screws.
  8. Attach parts J and K with the provided screws as indicated in the manual.
  9. Loosen the bolts of one side panel to slide the mattress base down to the lower position if needed. Make sure to retighten the bolts after adjusting the base.

Adjusting Mattress Base Height

The mattress base has two positions: low and high.

  1. For an active baby who can sit up unaided, set the base height to the low position.
  2. To adjust the base height, follow these steps:
  3. Remove the mattress from the cot.
  4. Loosen the bolts of one side panel to allow sliding the mattress base.
  5. Slide the mattress base up or down to the desired position.
  6. Retighten the bolts of the side panel.
  7. Place the mattress back into the cot.

Safety Precautions

  • Adult assembly is required. Keep small parts out of reach of children until assembly is complete.
  • Adjust the mattress base to the lowest position before the child can sit up unaided to prevent falls.
  • Ensure that the recommended mattress size is used: 690mm wide x 1300mm long and no more than 150mm thick.
  • The gaps between the mattress and the sides/ends of the cot should not exceed 40mm when pushed to one side or end, and 20mm when centered in the cot, to prevent limb entrapment.
  • The depth of the cot should be greater than 500mm with the mattress base in the lower position and greater than 300mm with the mattress base in the upper position to minimize the risk of a child climbing or falling out of the cot.

Care and Maintenance

Follow the care and maintenance instructions provided by the manufacturer.

FAQ

Q: What is the recommended mattress size for this cot?

A: The recommended mattress size is 690mm wide x 1300mm long and no more than 150mm thick.

Q: What is the maximum weight capacity of this cot?

A: The maximum weight capacity is 18kgs.

Q: Can I adjust the height of the mattress base?

A: Yes, the mattress base has two positions: low and high. Follow the instructions provided to adjust the base height.

Q: How should I clean and maintain this cot?

A: Please refer to the care and maintenance instructions provided by the manufacturer.

18 kg MAXIMUM WEIGHT

The photos and illustrations shown in this instruction manual are generic.
The manufacturer reserves the right to change any specification or feature without prior notice.

IMPORTANT. KEEP FOR FUTURE REFERENCE. READ CAREFULLY.

Read these instructions carefully before use and keep for future reference. The child may be hurt if you do not follow these instructions.

Supplied loose in box

anko-42956457-Wooden-Cot-In-Oak-Colour-fig-1

  • It is advisable that two people assemble the cot in the room in which it is to be used.
  • As small parts are involved in assembly, children should be kept dear of the assembly area.
  • Dispose of all packaging material immediately after the oot is assembled.
  • Identify all parts and oomponents.
  • Clear an area on the floor for assembly and place a sheet on the floor to ensure the cot is not scratched during assembly.

WARNING
DO NOT OVER TIGHTEN BOLTS. OVER TIGHTENING BOLTS CAN CAUSE PANELS TO CRACK

To assemble Cot

anko-42956457-Wooden-Cot-In-Oak-Colour-fig-2

lighten all bolts until firm. Do not over tighten bolts.
Over tightening bolts can cause panels to crack.

Mattress Base Heights

Mattress Base in High Position

This base height is set for when your baby is young and can not sit up unaided.

Mattress Base in Low Position
This base height is set for an active baby who can sit up unaided.

To adjust Mattress Base Height

anko-42956457-Wooden-Cot-In-Oak-Colour-fig-7

To assemble Cot

The oot is now ready for use in low base mode.

WARNING

ADULT ASSEMBLY REQUIRED:

DUE TO THE PRESENCE OF SMALL PARTS DURING ASSEMBLY, KEEP OUT OF REACH OF CHILDREN UNTIL ASSEMBLY IS COMPLETE. TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE THE CHILD CAN SIT UP UNAIDED.

RECOMMENDED MATTRESS SIZE:

  • 690mm WIDE x 1300mm LONG AND NO MORE THAN 150mm THICK. FOLLOW THE MANUFACTURER’S ASSEMBLY INSTRUCTIONS TO ENSURE THE SAFETY FEATURES OF THE COT ARE NOT COMPROMISED.
  • This cot has been manufactured for one child only, with a maximum weight of 18kgs.
  • When the mattress base is assembled in the lower position, ensure the higher cot base holes are covered tightly with the filling bolts supplied. This is to prevent finger entrapment, swallowing and inhalation hazards.
  • ENSURE the cot is placed at a reasonable distance from curtains, blinds, heaters and power points.
  • ENSURE the cot is completely assembled and check that all parts are securely tightened before placing the child into the cot.
  • ENSURE medication, string, elastic, small toys or small items such as money etc are always kept out of the child’s reach when in the cot.
  • DO NOT over tighten bolts/screws.
  • ENSURE that the child is clear of any moving parts when adjusting the cot.
  • For warranty purposes, keep your sales receipt to provide proof of purchase.

RECOMMENDED MATTRESS SIZE (SOLD SEPARATELY):
THIS COT HAS BEEN MANUFACTURED FOR USE WITH A MATTRESS WHICH MEASURES 690mm WIDE x 1300mm LONG AND NO MORE THAN 150mm THICK.

  • The width and length are specified because it is important that the gaps between the mattress and the sides and ends of the cot will not exceed 40 mm when the mattress is pushed to one side or end, and 20mm when the mattress is centred in the cot.
  • This is to minimise the danger of a child’s limb becoming caught in the gap.
  • The thickness of the mattress has been specified to ensure that the depth of the cot is greater than 500mm with the mattress base in the lower position and is greater than 300mm with the mattress base in the upper position to minimise the risk of a child climbing or falling out of the cot.

CARE AND MAINTENANCE

  • To ensure the long-lasting use of your cot, wipe down with a damp cloth and use a mild soap solution if necessary.
  • Do not use abrasive cleaners.
  • Always store product in a clean dry place.
  • Always check parts regularly for tightness of screws, nuts and other fasteners – tighten or replace if required.
  • To maintain the safety of your cot, seek prompt repairs for bent, torn, worn or broken parts.
  • Use only those parts and accessories approved and supplied by the manufacturer.

Keycode: 42956457
MADE IN CHINA
FOR AU / NZ: IMPORTED BY KMART
STORES IN AUSTRALIA AND NEW ZEALAND.
KMARTAUSTRALIA-690 SPRINGVALE ROAD, MULGRAVE, VIC 3170 AUSTRALIA.
KMART NEW ZEALAND – REGIONAL OFFICE C/O KMART PAPATOETOE STORE, HUNTERS PLAZA, GREAT SOUTH ROAD, PAPATOETOE, AUCKLAND, NEW ZEALAND.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals