JETSON 082-07-0153 3 Wheel Kick Scooter User Manual

JETSON 082-07-0153 3-Wheel Kick Scooter

Specifications

• Models: JPRNS-3KIK2; JMCKY-3KIK2; JGABY-3KIK2; JCOCO-3KIK2
• Handlebar
• Stem Clamp
• Stem
• Folding Mechanism
• Front Wheel (Motion-Activated LED Light-Up)
• Deck
• Rear Foot Brake
• Rear Wheel (Motion-Activated LED Light-Up)
• Tool Included: A 2-Bit 5mm Allen Key (A) and Phillips-Head Screwdriver (B)*

Product Overview
The 3-Wheel Kick Scooter is a fun and convenient mode of transportation. It features a sturdy handlebar, stem clamp, folding mechanism, motion-activated LED light-up front and rear wheels, a durable deck, and a rear foot brake for easy stopping.

Getting Started

Unfolding & Folding Your Scooter

To unfold your scooter:

1. Loosen the stem clamp knob by turning it counterclockwise using the Allen key tip of the 2-bit tool.
2. Pull open the latch located on the folding mechanism.
3. Press in the stem pin and raise or lower the handlebar until the pin clicks into another stem pin hole.
4. Close the stem clamp latch and tighten the knob by turning it clockwise with the Allen key.
5. Ensure that the handlebar is securely tightened. Always make sure the stem clamp latch is tightened and closed prior to riding. Do not over-tighten the stem clamp knob.

Adjusting the Handlebar

To adjust the handlebar:

1. Using the Allen key tip of the 2-bit tool, loosen the stem clamp knob by turning it counterclockwise.
2. Pull open the latch located on the folding mechanism.
3. Press in the stem pin and raise or lower the handlebar until the pin clicks into another stem pin hole.
4. Close the stem clamp latch and tighten the knob by turning it clockwise with the Allen key.
5. Check that the handlebar is secure. The stem pin alone will not keep the stem secure, so always make sure the stem clamp latch is tightened and closed prior to riding.
6. Note: Do not over-tighten the stem clamp knob as it can prevent the stem clamp latch from opening and closing properly.

Making Moves

Riding Your Scooter

1. Place one foot at the front of the deck facing forward.
2. Push the other foot off the ground to propel the scooter forward. Repeat as necessary to achieve or maintain desired speed.
3. To coast, place the kicking foot on the deck behind the front foot, turned outwards at a slight angle.
4. The wheel lights are motion-activated and will illuminate automatically whenever the wheels are rolling.

Turning
This scooter is a lean-to-steer scooter. To turn, slightly lean left or right while riding, and the scooter will veer accordingly.

Using the Brake
To slow down or come to a complete stop, press down gently with your rear riding foot. Apply more pressure to come to a complete stop.

Helmet Safety
A helmet should be worn by the rider at all times for safety. Proper positioning of the helmet is essential to prevent injury:

• Proper Positioning: The forehead is covered by the helmet.
• Improper Positioning: The forehead is exposed. A fall could result in serious injury.

It is recommended to wear appropriate clothing, closed-toe flat shoes, and safety gear. Avoid clothing that can get caught into or under the wheels. Wear an ASTM F1492 approved helmet and protective gear to prevent injury in the event of an accident.

FAQ’S

What are the models available for this scooter?
The available models for this scooter are JPRNS-3KIK2, JMCKY-3KIK2, JGABY- 3KIK2, and JCOCO-3KIK2.

Are the wheel lights motion-activated?
Yes, the wheel lights are motion-activated and will illuminate automatically whenever the wheels are rolling.

Can I adjust the handlebar height?
Yes, you can adjust the handlebar height by following the instructions provided in section 1.2 Adjusting the Handlebar.

Is a helmet necessary when riding this scooter?
Yes, it is highly recommended to wear a helmet at all times while riding this scooter for safety.

Safety Warnings

• Before use, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety instructions. The user will be responsible for any loss or damage caused by improper use.
• Before each cycle of operation, the operator shall perform the preoperation checks specified by the manufacturer:
  • That all guards and pads originally supplied by the manufacturer are in proper place and in serviceable condition;
  • That the braking system is functioning properly;
  • That any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable condition;
  • That tires are in good condition, inflated properly, and have sufficient tread remaining;
  • The area where the product is to be operated should be safe and suitable for safe operation.
• Components shall be maintained and repaired in accordance with the manufacturer’s specifications and using only the manufacturer’s authorized replacement parts with installation performed by dealers or other skilled persons.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zing) or rechargeable batteries.
• This product should not be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction (IEC 60335-1/A2:2006).
• Unsupervised children should not play with the product (IEC 60335-1/A2:2006).
• Adult supervision is required.
• The rider should not exceed 132 lb.
• Units shall not be operated to perform racing, stunt riding, or other maneuvers, which may cause loss of control or may cause uncontrolled operator passenger actions or reactions.
• Never use near motor vehicles.
• Avoid sharp bumps, drainage grates, and sudden surface changes. The scooter may suddenly stop.
• Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other debris. Wet weather impairs traction, braking, and visibility.
• Avoid riding around flammable gas, steam, liquid, or dust that could cause fire.
• Operators shall adhere to all of the manufacturer’s recommendations and instructions, as well as comply with all laws and ordinances: Units without headlights shall be operated only with adequate daylight conditions of visibility, and; Owners shall be encouraged to highlight (for conspicuity) using lighting, reflectors, and for low-riding units, signal flags on flexible poles.
• Persons with the following conditions shall be cautioned not to operate: Those with heart conditions; Pregnant women; Persons with head, back, or neck ailments, or prior surgeries to those areas of the body; and persons with any mental or physical conditions that may make them susceptible to injury or impair their physical dexterity or mental capabilities to recognize, understand, and perform all of the safety instructions and to be able to assume the hazards inherent in unit use.
• Do not ride at night.
• Do not ride after drinking or taking prescription medication.
• Do not carry items when riding.
• Never operate the product barefoot.
• Always wear shoes and keep shoelaces tied.
• Make sure your feet are always placed securely on the deck.
• Operators always shall use appropriate protective clothing, including but not limited to a helmet, with appropriate certification, and any other equipment recommended by the manufacturer: Always wear protective equipment such as helmet, knee pads, and elbow pads.
• Always give way to pedestrians.
• Be alert to things in front and far away from you.
• Do not allow distractions when riding, such as answering the phone or engaging in any other activities.
• The product cannot be ridden by more than one person.
• When you ride the product along with other riders, always keep a safe distance to avoid a collision.
• When turning, be sure to maintain your balance.
• Riding with improperly adjusted brakes is dangerous and can result in serious injury or death.
• The brake may become hot while operating, do not touch the brake with your bare skin.
• Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose control and fall. Sudden or excessive application of the brake may result in injury or death.
• If the brake loosens, please adjust with the hexagon wrench, or please contact the Jetson Care Team.
• Replace worn or broken parts immediately.
• Check whether all safety labels are in place and understood before riding.
• The owner shall allow the use and operation of the unit after a demonstration so that such operators can understand and operate all components of the unit before use.
• Do not ride without proper training. Do not ride at high speeds, on uneven terrain, or on slopes. Do not perform stunts or turn abruptly.
• Recommended for indoor use.
• Prolonged exposure to UV rays, rain, and the elements may damage the enclosure materials, store indoors when not in use.

MODIFICATIONS
Do not attempt to disassemble, modify, repair, or replace the unit or any components of the unit without instruction from the Jetson Care Team. This will void any warranty and can lead to malfunctions which may cause injury.

ADDITIONAL OPERATION PRECAUTIONS
Do not lift the product off the ground while it is on and the wheels are in motion. This can result in freely spinning wheels, which may cause injury to yourself or others nearby. Do not jump on or off the product, and do not jump while using it. Always keep your feet firmly planted on the footrest while in operation. Always check the battery charge before using.

DISPOSAL OF USED BATTERY
The battery may contain hazardous substances which could endanger the environment and human health. This symbol marked on the battery and/or packaging indicates that the used battery shall not be treated as municipal waste. Batteries should be disposed of at an appropriate collection point for recycling. By ensuring the used batteries are disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources. For more information about recycling of used batteries, please contact your local municipality waste disposal service.

• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.

California Proposition 65

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to: www.P65Warnings.ca.gov.

Warranty Coverage

GENERAL LIMITED WARRANTY
Your new Jetson product is warranted against defects in materials and workmanship as indicated on ridejetson.com/warranty for a period of time from the date of original retail purchase when used in accordance with Jetson’s user manuals (refer to ridejetson.com/support). Under this warranty, you will be able to direct your claims to Jetson even in situations where you purchased the Jetson Product from one of our authorized retailers. To read the full terms of our warranty, visit ridejetson.com/warranty.

TOOL INCLUDED:

2-BIT 5MM ALLEN KEY (A) AND PHILLIPS-HEAD SCREWDRIVER (B) TOOL PHILLIPS-HEAD SCREWDRIVER TIP NOT NEEDED FOR ASSEMBLY OR ADJUSTMENT OF THIS SCOOTER MODEL.

NOTE : IMAGES MAY NOT REFLECT THE EXACT APPEARANCE OF THE ACTUAL PRODUCT.

Specs & Features

• WHEELS: 4.75″ (FRONT), 3.1″ (REAR)
• UNFOLDED DIMENSIONS: 22.3″ (L) × 10.2″ (W) × 23.8″ (H)
• FOLDED DIMENSIONS: 23.0″ (L) × 10.2″ (W) × 6.3″ (H)
• DECK SIZE: 21.8″ (L) × 4.9″ (W)
• HANDLEBAR HEIGHT: 23.8″ – 31.5″
• WEIGHT LIMIT: 132 LBS
• PRODUCT WEIGHT: 7 LBS
• RECOMMENDED AGE: 2-4
• REAR FOOT BRAKE
• LED LIGHT-UP WHEELS
• EASY FOLDING TECHNOLOGY

Online Resources
Scan for our most updated scooter onboarding materials and support resources.

WARNING:
FAILURE TO COMPLY WITH THE FOLLOWING INSTRUCTIONS MAY RESULT IN INJURY TO THE CHILD OR OTHERS.

• KEEP SMALL PARTS AWAY FROM CHILDREN DURING ASSEMBLY.

• ACCESSORY MUST BE ASSEMBLED AND REMOVED BY AN ADULT.

• FREQUENTLY INSPECT THE PRODUCT FOR DAMAGE.

• ADULTS MUST ASSIST CHILDREN IN THE ASSEMBLY AND INITIAL ADJUSTMENT PROCEDURES OF THE PRODUCT.

Getting Started

Unfolding & Folding Your Scooter

• TO UNFOLD OR FOLD, FIRST SLIDE THE FOLDING MECHANISM UP THE STEM TOWARDS THE HANDLEBAR.
• TO UNFOLD: WHILE HOLDING THE FOLDING MECHANISM CLOSER TO THE HANDLEBAR, RAISE THE STEM UNTIL IT IS VERTICAL AND CLICKS INTO PLACE.
• TO FOLD: WHILE HOLDING THE FOLDING MECHANISM CLOSER TO THE HANDLEBAR, LOWER THE STEM DOWN TOWARDS THE REAR WHEEL UNTIL IT CLICKS INTO PLACE.

Adjusting the Handlebar

1. USING THE ALLEN KEY TIP OF THE 2-BIT TOOL, LOOSEN THE STEM CLAMP KNOB BY TURNING IT COUNTERCLOCKWISE.
2. PULL OPEN THE LATCH.
3. PRESS IN THE STEM PIN AND RAISE OR LOWER THE HANDLEBAR UNTIL THE PIN CLICKS INTO ANOTHER STEM PIN HOLE.
4. CLOSE THE STEM CLAMP LATCH AND TIGHTEN THE KNOB BY TURNING IT CLOCKWISE WITH THE ALLEN KEY.
5. CHECK THAT THE HANDLEBAR IS SECURE.

IMPORTANT : THE STEM PIN ALONE WILL NOT KEEP THE STEM SECURE. ALWAYS MAKE SURE THE STEM CLAMP LATCH IS TIGHTENED AND CLOSED PRIOR TO RIDING.

NOTE : DO NOT OVER-TIGHTEN THE STEM CLAMP KNOB. OVER-TIGHTENING CAN PREVENT THE STEM CLAMP LATCH FROM OPENING AND CLOSING.

Making Moves

Riding Your Scooter

1. PLACE ONE FOOT AT THE FRONT OF THE DECK FACING FORWARD.
2. PUSH THE OTHER FOOT OFF THE GROUND TO PROPEL THE SCOOTER FORWARD. REPEAT AS NECESSARY TO ACHIEVE OR MAINTAIN DESIRED SPEED.
3. TO COAST, PLACE THE KICKING FOOT ON THE DECK BEHIND

THE FRONT FOOT, TURNED OUTWARDS AT A SLIGHT ANGLE. THE WHEEL LIGHTS ARE MOTION-ACTIVATED AND WILL ILLUMINATE AUTOMATICALLY WHENEVER THE WHEELS ARE ROLLING.

Turning
THIS IS A “LEAN-TO-STEER” SCOOTER. TO TURN, SLIGHTLY LEAN LEFT OR RIGHT WHILE RIDING AND THE SCOOTER WILL VEER ACCORDINGLY.

Using the Brake
PRESS DOWN GENTLY WITH YOUR REAR RIDING FOOT TO SLOW DOWN. APPLY MORE PRESSURE TO COME TO A COMPLETE STOP.

Helmet Safety
A HELMET SHOULD BE WORN BY THE RIDER AT ALL TIMES.

• PROPER POSITIONING: THE FOREHEAD IS COVERED BY THE HELMET.
• IMPROPER POSITIONING: THE FOREHEAD IS EXPOSED. A FALL COULD RESULT IN SERIOUS INJURY.

Care & Maintenance

CLEANING THE SCOOTER

• TO CLEAN THE SCOOTER, CAREFULLY WIPE WITH A DAMP CLOTH AND THEN DRY WITH A DRY CLOTH.
• DO NOT APPLY WATER DIRECTLY TO THE SCOOTER. WATER CAN CAUSE DAMAGE OR DETERIORATION, WHICH COULD LEAD TO A MALFUNCTION THAT PUTS RIDER SAFETY AT RISK.

PRECAUTIONS

• KEEP AWAY FROM FIRE AND EXCESSIVE HEAT.
• AVOID INTENSE PHYSICAL IMPACT AND/OR SEVERE VIBRATION.
• RIDE THE SCOOTER ON A SMOOTH, FLAT SURFACE.
• PROTECT FROM WATER OR MOISTURE.
• CONTACT THE JETSON CARE TEAM IF THERE ARE ANY ISSUES WITH THE SCOOTER.

STORING THE SCOOTER

• STORE THE SCOOTER INDOORS AND IN A DRY PLACE.
• COVER THE SCOOTER TO PROTECT IT AGAINST DUST.

Stay connected. Be sure to follow @ridejetson on social media to learn about fantastic offers, giveaways, and all the latest Jetson news.

Loving your ride?
Then be sure to leave a review at ridejetson.com/reviews. We can’t wait to hear from you!

Questions?

Let us help. ridejetson.com/support ridejetson.com/chat To exercise your product’s warranty or inquire about warranty coverage, contact us directly. 1-888-976-9904 Manufactured in Yongkang, China Imported by Jetson Electric Bikes LLC. P.O. Box 320149, 775 4th Ave #2, Brooklyn, NY 11232 www.ridejetson.com

Made in China
Date Code: 10/2023 Document Edition: v1.0 © 2023, JETSON. ALL RIGHTS RESERVED. Manufactured by JETSON ELECTRIC BIKES LLC. No portion of this document, including shape, copy, graphics, and design, may be reproduced or transmitted in any form or by any means.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>