VEVOR 750 LBS Engine Stand User Manual

VEVOR 750 LBS Engine Stand User Manual

We continue to be committed to provide you tools with competitive price. “Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.

NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
CustomerService@vevor.com

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

SPECIFICATION

INSPECTION

• Inspect the equipment carefully before each use. Ensure the equipment is not damaged, excessively worn, or missing parts.

• Do not use the equipment unless it is properly lubricated.

• Using equipment that is not in good clean working condition or properly lubricated may cause serious injury.

• Inspect the work area before each use. Make sure it is free and clear of any potential hazards.
  DO NOT OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL.

• To maintain the equipment and user safety, the responsibility of the owner is to read and follow these instructions.

• Inspect the equipment for proper operation and function.

• Keep instructions readily available for equipment operators.

• Make certain all equipment operators are properly trained; understand how to safely and correctly operate the unit.

• Allow unit operation only with all parts in place and operating properly.

• Use only genuine replacement parts.

• Service and maintain the unit only with authorized or approved replacement parts; negligence will make the equipment unsafe for use and void the warranty.

• Carefully inspect the unit on a regular basis and perform all maintenance as required.

• Store these instructions in the handle of your equipment.

• Keep all decals on the unit clean and visible.

WARNING!

1. Study, understand, and follow all instructions before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces, with less than 3 degrees of slope.
4. Center load on mounting plate.
5. Mount and support only on areas of the engine as specified by the vehicle manufacturer.
6. Lock mounting plate rotating mechanism before applying a load.
7. Lock the wheels/casters before working on the engine.
8. Rotate the engine using the handle or device provided.
9. Assure load is cantered and secured to mounting attachments.
10. Off-center loads may make the load and handle rotate in either direction when the rotational locking device is released.
11. Release rotational locking devices slowly and carefully.
12. No alterations shall be made to this product.
13. Only attachments and/or adapters supplied by the manufacturer shall be used.
14. Never work directly under a supported load.
15. Do not use this product for any use other than the manufacturer specified usage.
16. Failure to heed these markings may result in personal injury and/or property damage.

MAINTENANCE INSTRUCTIONS

• Maintain your equipment. It is recommended that the general condition of any equipment be examined before it is used. Keep your equipment in good repair by adopting a program of conscientious repair and maintenance. Have necessary repairs made by qualified service personnel.
• Follow the maintenance instructions carefully to keep your equipment in good working condition. Never perform any maintenance on the equipment while it is under a load. a. All moving parts of the equipment should be regularly cleaned. b. Lubricate parts as required by the manufacturer’s specifications. The type of lubricant should be as specified by the manufacturer or a qualified person. Lubrication systems should be checked to verify proper operation. c. If additional maintenance is required, it should be completed in accordance with the instructions of the manufacturer or qualified person.

Inspection You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all components function before each use. Follow lubrication and storage instructions for optimum product performance. Check the climbing pins to make sure that they are not worn or damaged. Check that everything is good working condition and that nothing is blocking the holes. Do not use the equipment unless it is in good working condition.

Binding If the product binds while under a load, use equipment with equal or a larger load capacity to lower the load safely to the ground. After un-binding; clean, lubricate and test that equipment is working properly. Rusty components, dirt, or worn parts can be causes of binding Clean and lubricate the equipment as indicated in the lubrication section. Test the equipment without a load. If the binding continues, contact Customer Service.

IF YOUR EQUIPMENT BINDS
As your equipment becomes older, the threads may start binding. This will prevent the equipment from operating properly and safely. Rusty threads, dirty threads, or a worn threads can cause binding. Clean and lubricate the equipment. Test the equipment without a load. If the binding continues, refer to the after sale parts and service. If your equipment binds while under a load, use equipment with equal or larger load capacity to lower the load safely to the ground.
Cleaning If the moving parts of the equipment are obstructed, use cleaning solvent or another good degreaser to clean the equipment. Remove any existing rust, with a penetrating lubricant. Do not use motor oil to lubricate the equipment Rust Prevention:
– Check daily for any signs of rust or corrosion. Without a load check for signs of rust that are visible and clean as needed. Storing the Equipment

1. Store in a dry location, recommended indoors.
2. Equipment should be stored in an area where they will not be subjected to damage.
3. If extreme temperatures or chemically active or abrasive environments are involved, the guidance provided in shall be followed.
4. Temperature – When equipment are to be used at temperatures above 140″F (60″C) or below -20″F (-29″C), the equipment manufacturer or a qualified person should be consulted.
5. Chemically Active Environments -The strength and operation of equipment can be affected by chemically active environments such as caustic or acid substances or fumes. The equipment manufacturer or a qualified person should be consulted before equipment are used in chemically active environments.
6. Other Environments – The internal workings of equipment can be affected by high moisture, gravel or sand, silt, grit, or other dust-laden air. Equipment subject to these environments should have their inner components frequently cleaned, inspected, and lubricated.

Note: If the equipment is stored outdoors, be sure to lubricate all parts before and after use to ensure the equipment stays in good working condition.

ASSEMBLY INSTRUCTIONS

1. Attach crossbeam(13) and rear support axle (10) to main post (9) with bolt (11),washer(14), spring washer (15)and Nut(16).
2. Attach brake wheels(21) to anterior support axle (20) with washer (17), spring washer (18) and nut (19).Cover the end cover(23)at last.
3. Attach anterior support axle (20) to crossbeam(13)with bolt (11), washer (14), spring washer (15) and nut (16).
4. Attach mounting arms (7) to head assembly (6) with bolt (8), washer (5), spring washer (4) and nut (3).
5. Insert the head assembly (6) into the hole of the main post (9). Line up the hole in the head assembly (6) and the main post (9), and assembly them by inserting the lock pin (2).
6. Insert the handle assembly(6) into the hole of the head assembly (6).
7. Tight all the screws.

ASSEMBLY DIAGRAM

Importer: WAITCHX Address: 250 bis boulevard Saint-Germain 75007 Paris Importer: FREE MOOD LTD Address: 2 Holywell Lane, London, England, EC2A 3ET

UK
EUREP UK LTD
UNIT 2264, 100 OCK STREET, ABINGDONOXFORDSHIRE ENGLAND OX14 5DH

REP
EUREP GmbH
Unterlettenweg 1a, 85051
Ingolstadt, Germany

Manufacturer: Haiyan Xinxing Mechanical And Electrical. Co., Ltd AddressLiuzhuang Village Xitang qiao Street Haiyan County Zhejiang Province
Made In China

Technical Support and E-Warranty Certificate https://www.vevor.com/support

References

• Contact Us – Official VEVOR Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>