CHAMBERLAIN WD1000WF 1-1 4 hps Belt Drive Garage Door Opener with MyQ Smartphone Control and Battery Backup Instruction Manual

CHAMBERLAIN WD1000WF 1-1 4 hps Belt Drive Garage Door Opener with MyQ

Smartphone Control and Battery Backup

Product Information

Specifications

• Model: Chamberlain Garage Door Opener
• Usage: Residential use only
• Horsepower: 1-1/4 HP (similar)
• Manufacturer: The Chamberlain Group, Inc.
• Address: 845 Larch Avenue, Elmhurst, Illinois 60126-1196
• Website: www.chamberlain.com

Product Usage Instructions

Preparation

Before you begin the installation of the Chamberlain Garage Door Opener, please ensure the following steps are followed:

1. Disable any locks and remove any ropes connected to the garage door.

2. Lift the door halfway up and release it. If the door is balanced, it should stay in place, supported entirely by its springs.

3. Raise and lower the door to check for any binding or sticking.
   If you notice any issues, such as the door binding, sticking, or being out of balance, it is recommended to call a trained door systems technician for assistance.

4. Check the seal on the bottom of the door. Ensure that there is no more than a 1/4 inch (6 mm) gap between the floor and the bottom of the door. If there is a larger gap, the safety reversal system\ may not work properly.

5. The opener should be installed above the center of the door. If there is a torsion spring or center bearing plate obstructing the header bracket, it can be installed within 4 feet (1.2 m) to the left or right of the door center. Refer to page 11 of the manual for more details.

Electrical

To ensure the safety and proper functioning of your garage door opener, it is important to follow these electrical guidelines:

• Disable any locks before installing and operating the opener.
• Only operate the garage door opener at 120V, 60 Hz to avoid malfunctions and damage.

Unattended Operation

To prevent damage to the garage door and opener, please take note of the following precautions:

• Always disable locks before installing and operating the opener.
• Operate the garage door opener only at the recommended voltage of 120V, 60 Hz.

Frequently Asked Questions

• Q: Can I install this garage door opener on a one-piece door?
  • A: No, this garage door opener should not be installed on a one-piece door if using devices or features providing unattended close. Unattended devices and features are to be used only with sectional doors.
• Q: Where can I find the model number of my garage door opener?
  • A: The model number label is located on the left side panel of your garage door opener.

1-1/4 hps* Belt Drive Garage Door Opener with MyQ® Smartphone Control and Battery Backup
Models
· WD1000WF · HD950WF · LW9000WF
FOR RESIDENTIAL USE ONLY

Please read this manual and the enclosed safety materials carefully!
Fasten the manual near the garage door after installation.
The door WILL NOT CLOSE unless the Protector System® is connected and properly aligned.
Periodic checks of the garage door opener are required to ensure safe operation.
The model number label is located on the left side panel of your garage door opener.
This garage door opener is compatible with MyQ® and Security+ 2.0® accessories.
DO NOT install on a one-piece door if using devices or features providing unattended close. Unattended devices and features are to be used ONLY with sectional doors.

Write down the MyQ® serial number located on the garage door opener:
*Horsepower similar (hps) designates that this garage door opener system meets Chamberlain’s pulling force specification for a 1-1/4 horsepower garage door opener.

www.chamberlain.com www.mychamberlain.com
The Chamberlain Group, Inc. 845 Larch Avenue
Elmhurst, Illinois 60126-1196

o

Preparation

Safety Symbol and Signal Word Review
This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully.
Mechanical

Check the Door
To prevent possible SERIOUS INJURY or DEATH: l ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance.
An unbalanced garage door may NOT reverse when required. l NEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or
their hardware, ALL of which are under EXTREME tension. l Disable ALL locks and remove ALL ropes connected to garage door BEFORE installation and
operating garage door opener to avoid entanglement. l DO NOT install on a one- piece door if using devices or features providing unattended close.
Unattended devices and features are to be used ONLY with sectional doors.

Electrical

When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the cautionary statements that accompany it. Read them carefully.
Unattended Operation
The Timer-to-Close (TTC) feature, the MyQ® Smartphone Control app, and MyQ® Garage Door and Gate Monitor are examples of unattended close and are to be used ONLY with sectional doors. Any device or feature that allows the door to close without being in the line of sight of the door is considered unattended close. The Timer-to-Close (TTC) feature, the MyQ® Smartphone Control, and any other MyQ® devices are to be used ONLY with sectional doors.

To prevent damage to garage door and opener: l ALWAYS disable locks BEFORE installing and operating the opener. l ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage.

Before you begin:
1. Disable locks and remove any ropes connected to the garage door. 2. Lift the door halfway up. Release the door. If balanced, it should stay in
place, supported entirely by its springs. 3. Raise and lower the door to check for binding or sticking. If your door
binds, sticks, or is out of balance, call a trained door systems technician. 4. Check the seal on the bottom of the door. Any gap between the floor and the bottom of the door must not exceed 1/4 inch (6 mm). Otherwise, the safety reversal system may not work properly.
5. The opener should be installed above the center of the door. If there is a torsion spring or center bearing plate in the way of the header bracket, it may be installed within 4 feet (1.2 m) to the left or right of the door center. See page 11.

Torsion Extension Spring OR Spring

2

o

Preparation
Test the Wi-Fi® Signal Strength in your garage
You will need a router with Wi-Fi and a smartphone or other mobile device. Make sure your mobile device is connected to your Wi-Fi network. Hold your mobile device in the place where your garage door opener will be installed and check the Wi-Fi signal strength.
Check Signal Strength. If you see:
Wi-Fi signal is strong. You’re all set! Install your new garage door opener.
Wi-Fi signal is weak. The garage door opener will likely connect to your Wi-Fi network. If not, try one of the options below.
No Wi-Fi signal. Try one of the following: · Move your router closer to the garage door opener to
minimize interference from walls and other objects · Buy a Wi-Fi range extender · Buy a Chamberlain MyQ® Internet Gateway (CIGBU) see page 41
Visit wifihelp.chamberlain.com for more details See MyQ® Smartphone Control page 32 to connect your garage door opener to your Wi-Fi network.

Tools Needed

Additional Items You May Need:

Survey your garage area to see if you will need any of the following items:

l (2) 2X4 Pieces of wood : May be used to fasten the header bracket to the structural supports.

5/32

Also used to position the garage door opener during installation and for testing the safety

3/16

reversing sensors.

5/16

l Support bracket and fastening hardware: Must be used if you have a finished ceiling in your

garage.

l Extension brackets (MODEL 041A5281-1) or wood blocks: Depending upon garage

construction, extension brackets or wood blocks may be needed to install the safety reversing

sensor.

l Fastening hardware: Alternate floor mounting of the safety reversing sensor will require

hardware not provided. l Door reinforcement: Required if you have a lightweight steel, aluminum, fiberglass or glass

1/2

panel door. l Rail extension kit: Required if your garage door is more than 7 feet (2.13 m) high.

5/8 7/16

1/4 9/16

7/16

3
o

Preparation
Carton Inventory
Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below. Accessories vary depending on the garage door opener model purchased. Depending on your model, other accessories may be included with your garage door opener. Instructions for these accessories will be attached to the accessory and are not included in this manual. Save the carton and packing material until the installation and adjustment is complete. The images throughout this manual are for reference only and your product may look different.
A. Header bracket B. Pulley C. Door bracket D. Curved door arm E. Straight door arm
(Packaged inside front rail section) F. Trolley
NOTE: Be sure to assemble the trolley before sliding onto rail. G. Emergency release rope and handle H. Rail (1 front and 4 center sections) I. Hanging brackets (2)
(Packaged inside the front rail section) J. Garage door opener (motor unit) K. Sprocket cover and screws L. “U” bracket M. Belt N. Door control (Smart Control Panel®) O. Remote control (2) P. The Protector System®
Safety reversing sensors with 2 conductor white and white/black wire attached: Sending Sensor (1), Receiving Sensor (1), and Safety Sensor Brackets (2) NOT SHOWN White and red/white wire Owner’s manual Hardware
4
o

Preparation
Hardware

ASSEMBLY

Bolt

Bolt

1/4″-20×1-3/4″

INSTALLATION
Self-Threading Screw 1/4″-14×5/8″ (2)

Lag Screw 5/16″-9×1-5/8″ (4)

Threaded Shaft with
Spring Trolley Nut

Clevis Pin 5/16″x1-1/2″

Clevis Pin 5/16″x1-1/4″

Clevis Pin 5/16″x1″

Carriage Bolt 1/4″-20×1/2″ (2)

Wing Nut 1/4″-20 (2)

Hex Bolt 5/16″-18×7/8″ (4)

Lock Nut 1/4″-20

Master Link
Hex Screw #8×3/8″ (2) (packed with the sprocket cover)

Nut 3/8″

Lock Washer 3/8″

Nut 5/16″-18 (6)

Lock Washer 5/16″-18 (5)

Drywall Anchors (2)

DOOR CONTROL Screw 6-32×1″ (2)
Screw 6ABx1″ (2)

5
o

Ring Fastener (3)
Insulated Staples (Not Shown)

Assembly
STEP 1 Assemble the rail and install the trolley

To prevent INJURY from pinching, keep hands and fingers away from the joints while assembling the rail.
To avoid installation difficulties, do not run the garage door opener until instructed to do so. The front rail has a cut out “window” at the door end. The rail tab MUST be on top of the rail when assembled.
1. Remove the straight door arm and hanging bracket packaged inside the front rail and set aside for Installation Step 5 and 9. NOTE: To prevent INJURY while unpacking the rail carefully remove the straight door arm stored within the rail section.
2. Align the rail sections on a flat surface as shown and slide the tapered ends into the larger ones. Tabs along the side will lock into place.
3. Place the motor unit on packing material to protect the cover, and rest the back end of the rail on top. For convenience, put a support under the front end of the rail.
4. As a temporary stop, insert a screwdriver into the hole in the second rail section from the motor unit, as shown.
5. Check to be sure there are 4 plastic wear pads inside the inner trolley. If they became loose during shipping, check all packing material. Snap them back into position as shown.
6. Slide the trolley assembly toward the screwdriver as shown. 7. Slide the rail onto the “U” bracket, until it reaches all the stops on the top and sides of the “U”
bracket.

Outer Trolley Inner Trolley
Wear Pads
Rail Tab
Front Rail Section (TO DOOR)

SLIDE TO STOPS ON TOP AND SIDES OF “U” BRACKET

“U” Bracket

To garage door opener (TO MOTOR UNIT)

Trolley

6
o

Assembly
STEP 2 Fasten the rail to the motor unit
To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener.
1. Insert a 1/4″-20 x 1-3/4″ bolt into the cover protection bolt hole on the back end of the rail as shown. Tighten securely with a 1/4″-20 lock nut. DO NOT overtighten.
2. Remove the bolts from the top of the motor unit. 3. Use the carton to support the front end of the rail. 4. Place the “U” bracket, flat side down onto the motor unit and align the bracket holes with the
bolt holes. 5. Fasten the “U” bracket with the previously removed bolts; DO NOT use any power tools. The
use of power tools may permanently damage the garage door opener.
HARDWARE

STEP 3 Install the idler pulley
1. Lay the belt beside the rail, as shown. Grasp the end with the hooked trolley connector and pass approximately 12″ (30 cm) of belt through the window. Keep the ribbed side toward the rail, and allow it to hang until Assembly Step 4.
2. Remove the tape from the idler pulley. The inside center should be pre- greased. If dry, regrease to ensure proper operation.
3. Place the idler pulley into the window as shown. 4. Insert the idler bolt from the top through the rail and pulley. Tighten with a 3/8″ lock washer
and nut underneath the rail until the lock washer is compressed. 5. Rotate the pulley to be sure it spins freely. 6. Locate the rail tab. The rail tab is between the idler bolt and the trolley in the front rail section.
Use a flathead screwdriver and lift the rail tab until the tab is vertical (90º).

HARDWARE

Bolt

Lock Washer 3/8″

Nut 3/8″

Bolt 1/4″-20×1-3/4″ Bolts (Mounted in the garage door opener)
“U” Bracket Bolt 1/4″-20×1-3/4″
Cover Protection Bolt Hole

Lock Nut 1/4″-20

Lock Nut 1/4″-20

7
o

Rail Tab

CORRECT

INCORRECT

Bolt Rail Tab
Lock Washer 3/8″ Nut 3/8″

Rail
Grease Inside Pulley Idler Pulley Trolley Connector

Assembly
STEP 4 Install the belt
1. Pull the belt around the idler pulley and toward the trolley. The ribbed side must contact the pulley.
2. Hook the trolley connector into the retaining slot on the trolley as shown (Figure 1). 3. With the trolley against the screwdriver, dispense the remainder of the belt along the rail
length toward the motor unit and around the sprocket (Figure 2). The sprocket teeth must engage the belt. 4. Check to make sure the belt is not twisted. Connect the trolley threaded shaft with the master link (Figure 3).
l Push pins of master link bar through holes in end of belt and trolley threaded shaft. l Push master link cap over pins and past pin notches. l Slide the closed end of the clip-on spring over one of the pins. Push the open end of the
clip-on spring onto the other pin. 5. Remove the spring trolley nut from the threaded shaft. 6. Insert the trolley threaded shaft through the hole in the trolley.
HARDWARE Threaded Shaft with Spring Trolley Nut
Master Link

Figure 1
Trolley Connector
Retaining Slot
Figure 3
Master Link

Figure 2
Sprocket
Threaded Shaft

8
o

Assembly
STEP 5 Tighten the belt
1. By hand, thread the spring trolley nut on the threaded shaft until it is finger tight against the trolley. Do not use any tools. Remove the screwdriver.
2. Insert a flathead screwdriver tip into one of the nut ring slots and brace it firmly against the trolley.
3. Tighten the spring trolley nut with an adjustable wrench or a 7/16″ open end wrench about a quarter turn until the spring releases and snaps the nut ring against the trolley. This sets the spring to optimum belt tension.

Spring Trolley Nut

Nut Ring Slot

Nut Ring

Nut Ring

STEP 6 Install the sprocket cover
To avoid possible SERIOUS INJURY to finger from moving garage door opener: l ALWAYS keep hand clear of sprocket while operating opener. l Securely attach sprocket cover BEFORE operating.
1. Position the sprocket cover over the sprocket as shown and fasten to the mounting plate with 8×3/8″ hex screws provided.
You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section.
HARDWARE
Hex Screw #8×3/8″ (Packed with the sprocket cover)

BEFORE 1″
(2.5 cm)

AFTER 1-1/4″ (3.18 cm)

Hex Screw #8×3/8″ Sprocket Cover

9
o

Installation

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS. 2. Install garage door opener ONLY on properly balanced and lubricated garage door. An
   improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH. 3. ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener. 4. Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener to avoid entanglement. 5. Install garage door opener 7 feet (2.13 m) or more above floor. 6. Mount the emergency release within reach, but at least 6 feet (1.83 m) above the floor and avoiding contact with vehicles to avoid accidental release. 7. NEVER connect garage door opener to power source until instructed to do so. 8. NEVER wear watches, rings or loose clothing while installing or servicing opener. They could be caught in garage door or opener mechanisms.

2. Install wall-mounted garage door control: l within sight of the garage door. l out of reach of children at minimum height of 5 feet (1.5 m). l away from ALL moving parts of the door.
   10. Place entrapment warning label on wall next to garage door control. 11. Place manual release/safety reverse test label in plain view on inside of garage door. 12. Upon completion of installation, test safety reversal system. Door MUST reverse on contact with a
   1-1/2″ (3.8 cm) high object (or a 2×4 laid flat) on the floor. 13. To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric
   and battery power BEFORE performing ANY service or maintenance. 14. DO NOT install on a one-piece door if using devices or features providing unattended close.
   Unattended devices and features are to be used ONLY with sectional doors.

10
o

Installation
STEP 1 Determine the header bracket location
To prevent possible SERIOUS INJURY or DEATH: l Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling,
otherwise garage door might NOT reverse when required. DO NOT install header bracket over drywall. l Concrete anchors MUST be used if mounting header bracket or 2×4 into masonry. l NEVER try to loosen, move or adjust garage door, springs, cables, pulleys, brackets, or their hardware, ALL of which are under EXTREME tension. l ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door might NOT reverse when required.
Installation procedures vary according to garage door types. Follow the instructions which apply to your door.
1. Close the door and mark the inside vertical centerline of the garage door. 2. Extend the line onto the header wall above the door.You can fasten the header bracket within
4 feet (1.22 m) of the left or right of the door center only if a torsion spring or center bearing plate is in the way; or you can attach it to the ceiling (see page 12) when clearance is minimal. (It may be mounted on the wall upside down if necessary, to gain approximately 1/2″ (1 cm). If you need to install the header bracket on a 2×4 (on wall or ceiling), use lag screws (not provided) to securely fasten the 2×4 to structural supports as shown here and on page 12. 3. Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall 2″ (5 cm) above the high point: l 2″ (5 cm) above the high point for sectional door and one-piece door with track. l 8″ (20 cm) above the high point for one-piece door without track. This height will provide travel clearance for the top edge of the door. NOTE: If the total number of inches exceeds the height available in your garage, use the maximum height possible, or refer to page 12 for ceiling installation.
11

Header Wall Vertical Centerline of Garage Door
2×4 Structural Supports

OPTIONAL CEILING MOUNT FOR HEADER BRACKET
Unfinished Ceiling

Level (Optional)

Sectional door with curved track
Header Wall 2″ (5 cm)
Track
Highest Point of Travel Door

One-piece door without track: jamb hardware

Door
Jamb Hardware

Header Wall 8″ (20 cm)
Highest Point of Travel

2×4

One-piece door with horizontal track
Header Wall 2″ (5 cm)

Door

Track

Highest Point of Travel

One-piece door without track: pivot hardware
Header Wall 8″ (20 cm)

Highest

Door

Point of

Travel

Pivot

o

Installation
STEP 2 Install the header bracket
You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided).
HARDWARE
Lag Screw 5/16″-9×1-5/8″
OPTION A WALL INSTALLATION
1. Center the bracket on the vertical centerline with the bottom edge of the bracket on the horizontal line as shown (with the arrow pointing toward the ceiling).
2. Mark the vertical set of bracket holes. Drill 3/16″ pilot holes and fasten the bracket securely to a structural support with the hardware provided.

Wall Mount UP

(Header Wall)
2×4 Structural Support

Horizontal Line

Header Bracket

Vertical Centerline of Garage Door
Lag Screw 5/16″-9×1-5/8″

OPTION B CEILING INSTALLATION
1. Extend the vertical centerline onto the ceiling as shown. 2. Center the bracket on the vertical mark, no more than 6″ (15 cm) from the wall. Make sure the
arrow is pointing away from the wall. The bracket can be mounted flush against the ceiling when clearance is minimal. 3. Mark the side holes. Drill 3/16″ pilot holes and fasten bracket securely to a structural support with the hardware provided.

Ceiling Mounting Holes
UP

Header Bracket
6″ (15 cm) Maximum
Door Spring

(Garage Door)

(Finished Ceiling)
Vertical Centerline of Garage Door Lag Screw 5/16″-9×1-5/8″ (Header Wall)

Optional Mounting Holes
Highest Point of Garage Door Travel

Door Spring (Garage Door)

12
o

Installation

STEP 3 Attach the rail to the header bracket
1. Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way, you will need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring.
2. Position the rail bracket against the header bracket. 3. Align the bracket holes and join with a clevis pin as shown. 4. Insert a ring fastener to secure.
HARDWARE

Clevis Pin 5/16″x1-1/2″

Ring Fastener

Clevis Pin 5/16″x1-1/2″

Ring Fastener

STEP 4 Position the garage door opener

To prevent damage to garage door, rest garage door opener rail on 2×4 placed on top section of door.
1. Remove the packing material and lift the garage door opener onto a ladder. 2. Fully open the door and place a 2×4 (laid flat) under the rail. For one- piece doors without
tracks, lay the 2×4 on it’s side.
NOTE: A 2×4 is ideal for setting the distance between the rail and the door. If the ladder is not tall enough you will need help at this point. If the door hits the trolley when it is raised, pull the trolley release arm down to disconnect the inner and outer trolley. Slide the outer trolley toward the garage door opener. The trolley can remain disconnected until instructed.

Connected

Disconnected

All other door types

One-piece door without tracks

13
o

Installation
STEP 5 Hang the garage door opener

To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural supports of the garage. Concrete anchors MUST be used if installing ANY brackets into masonry.
Hanging the garage door opener will vary depending on your garage. Below are three example installations. Your installation may be different. For ALL installations the garage door opener MUST be connected to structural supports. The instructions illustrate one of the examples below.

Finished Ceiling

Unfinished Ceiling

1. On finished ceilings, use the lag screws to attach a support bracket (not provided) to the structural supports before installing the garage door opener.
   2. Make sure the garage door opener is aligned with the header bracket. Measure the distance from each side of the garage door opener to the support bracket.
   3. Cut both pieces of the hanging bracket to required lengths. 4. Attach the end of each hanging bracket to the support bracket with appropriate hardware (not
   provided). 5. Attach the garage door opener to the hanging brackets with the hex bolts, lock washers, and
   nuts. 6. Remove the 2×4 and manually close the door. If the door hits the rail, raise the header bracket.

1 Finished Ceiling

2 (not provided)

(not provided) 3

Lag Screw 5/16″9×1-5/8″

Lag Screw 5/16″9×1-5/8″

HARDWARE

4

5 Hex Bolt

6

Lag Screw 5/16″-9×1-5/8″

Lock Washer

5/16″- 18×7/8″

5/16″-18

Lock Washer

Nut 5/16″-18

(not provided)

5/16″-18 Nut 5/16″-18

Hex Bolt 5/16″- 18×7/8″

14
o

Installation
STEP 6 Install the light bulbs

STEP 7 Attach the emergency release rope and handle

To prevent possible OVERHEATING of the end panel or light socket: l Use ONLY A19 incandescent (100W maximum) or compact fluorescent (26W maximum) light
bulbs. l DO NOT use incandescent bulbs larger than 100W. l DO NOT use compact fluorescent light bulbs larger than 26W (100W) equivalent. l DO NOT use halogen bulbs. l DO NOT use short neck or specialty light bulbs.
1. Pull on the top sides of the light lens and rotate the light lens down. 2. Insert an A19 incandescent (100W maximum) or compact fluorescent (26W, 100W
equivalent) light bulb into the light socket. 3. Rotate the lens up to close. NOTE: Do not use halogen, short neck, or specialty light bulbs as these may overheat the end panel or light socket. Do not use LED bulbs as they may reduce the range or performance of your remote controls.
or or

To prevent possible SERIOUS INJURY or DEATH from a falling garage door:
l If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.
l NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.
l NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.
1. Insert one end of the emergency release rope through the handle. Make sure that “NOTICE” is right side up. Tie a knot at least 1 inch (2.5 cm) from the end of the emergency release rope.
2. Insert the other end of the emergency release rope through the hole in the trolley release arm. Mount the emergency release within reach, but at least 6 feet (1.83 m) above floor, avoiding contact with vehicles to prevent accidental release and secure with a knot.
NOTE: If it is necessary to cut the emergency release rope, seal the cut end with a match or lighter to prevent unraveling. Ensure the emergency release rope and handle are above the top of all vehicles to avoid entanglement.

15
o

Installation
STEP 8 Install the door bracket
Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact the garage door manufacturer or installing dealer for opener reinforcement instructions or reinforcement kit. Failure to reinforce the top section as required according to the door manufacturer may void the door warranty.
A horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, aluminum, steel, doors with glass panel, etc.) (not provided). A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel. Contact the garage door manufacturer or installing dealer for opener reinforcement instructions or reinforcement kit. NOTE: Many door reinforcement kits provide for direct attachment of the clevis pin and door arm. In this case you will not need the door bracket; proceed to the next step.
HARDWARE
Self-Threading Screw 1/4″-14×5/8″
OPTION A SECTIONAL DOORS
1. Center the door bracket on the previously marked vertical centerline used for the header bracket installation. Note correct UP placement, as stamped inside the bracket.
2. Position the top edge of the bracket 2″-4″ (5-10 cm) below the top edge of the door, OR directly below any structural support across the top of the door.
3. Mark, drill holes and install as follows, depending on your door’s construction.

Metal or light weight doors using a vertical angle iron brace between the door panel support and the door bracket:
l Drill 3/16″ fastening holes. Secure the door bracket using the two 1/4″-14×5/8″ self-threading screws. (Figure 1)
l Alternately, use two 5/16″-18×2″ bolts, lock washers and nuts (not provided). (Figure 2)
Metal, insulated or light weight factory reinforced doors: l Drill 3/16″ fastening holes. Secure the door bracket using the self-threading screws. (Figure 3)
Wood doors: l Use top and bottom or side to side door bracket holes. Drill 5/16″ holes through the door and secure bracket with 5/16″-18-2″ carriage bolts, lock washers and nuts (not provided). (Figure 4)
NOTE: The 1/4″-14×5/8″ self-threading screws are not intended for use on wood doors.

FIGURE 1

Vertical Reinforcement

FIGURE 2

Vertical Centerline of Garage Door

Vertical Reinforcement Vertical Centerline of Garage Door
Door Bracket

UP

UP

Door Bracket
Self-Threading Screw 1/4″-14×5/8″

Hardware (not provided)

FIGURE 3

Vertical Centerline of Garage Door

FIGURE 4
Hardware (not provided)

Inside Edge of Door or Reinforcement Board

UP

UP

Self-Threading Screw 1/4″-14×5/8″

Vertical Centerline of Garage Door

16

o

Installation
STEP 8 Install the door bracket (continued) OPTION B ONE-PIECE DOORS
1. Center the door bracket on the top of the door, in line with the header bracket as shown. 2. Mark either the left and right, or the top and bottom holes. Metal Doors: l Drill 3/16″ pilot holes and fasten the bracket with the self-threading screws provided. Wood Doors: l Drill 5/16″ holes and use 5/16″-18×2″ carriage bolts, lock washers and nuts (not provided) or
5/16″x1-1/2″ lag screws (not provided) depending on your installation needs. NOTE: The door bracket may be installed on the top edge of the door if required for your installation. (Refer to the dotted line optional placement drawing.)

Header Wall 2×4 Support
Header Bracket

(Finished Ceiling)

Door Bracket

Optional Placement of Door Bracket

Vertical Centerline of Garage Door

For a door with no exposed framing, or for the optional installation, use lag screws 5/16″x1-1/2″ (not provided) to fasten the door bracket.

Metal Door
Door Bracket

Self-Threading Screw 1/4″-14×5/8″
Top of Door (Inside Garage)
Top Edge of Door

Wood Door
Door Bracket

Optional Placement

Hardware (not provided)
Top of Door (Inside Garage)
Top Edge of Door
Optional Placement
Hardware (not provided)

17
o

Installation
STEP 9 Connect the door arm to the trolley
Installation will vary according to the garage door type. Follow the instructions which apply to your door.
OPTION A SECTIONAL DOORS
IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. 1. Close the door. Disconnect the trolley by pulling the emergency release handle. 2. Attach the straight door arm to the outer trolley using the clevis pin. Secure with the ring fastener. 3. Attach the curved door arm to the door bracket using the clevis pin. Secure with the ring fastener. 4. Bring arm sections together. Find two pairs of holes that line up and join sections. Select holes as far apart as possible to increase door arm rigidity and attach using the bolts, nuts, and lock washers. 5. Pull the emergency release handle toward the garage door opener until the trolley release arm is horizontal. The trolley will re-engage automatically when the garage door opener is activated.
NOTE: If the holes in the curved door arm and the straight door arm do not align, reverse the straight door arm, select two holes (as far apart as possible) and attach using bolts, nuts, and lock washers. If the straight door arm is hanging down too far, you may cut 6 inches (15 cm) from the solid end.
HARDWARE

Clevis Pin 5/16″x1-1/4″

Clevis Pin 5/16″x1″

Hex Bolt 5/16″-18×7/8″

Ring Fastener

Lock Washer 5/16″ -18

Nut 5/16″-18

CORRECT
Straight Door Arm
(Groove facing out)

Curved Door Arm

INCORRECT
Straight Door Arm

Curved Door Arm

Ring Fastener
Nut 5/16″-18

Lock Washer 5/16″ -18

Clevis Pin 5/16″x1″

Hex Bolt 5/16″-18×7/8″ Clevis Pin 5/16″x1-1/4″

18
o

Installation
STEP 9 Connect the door arm to the trolley (continued) OPTION B ONE-PIECE DOORS
IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. 1. Close the door. Disconnect the trolley by pulling the emergency release handle. 2. Fasten the straight door arm and the curved door arm together to the longest possible length (with a 2 or 3 hole overlap) using the bolts, nuts, and lock washers. 3. Attach the straight door arm to the door bracket using the clevis pin. Secure with the ring fastener. 4. Attach the curved door arm to the trolley using the clevis pin. Secure with the ring fastener. 5. Pull the emergency release handle toward the garage door opener until the trolley release arm is horizontal.
HARDWARE

Clevis Pin 5/16″x1-1/4″

Clevis Pin 5/16″x1″

Hex Bolt 5/16″-18×7/8″

Ring Fastener

Lock Washer 5/16″ -18

Nut 5/16″-18

CORRECT

Straight Door Arm
(Groove facing out)

Curved Door Arm

INCORRECT

Straight Door Arm

Curved
Door Arm

One-Piece Door without Track

Ring Fastener

Ring Fastener Nut 5/16″-18

Lock Washer 5/16″ -18

Clevis Pin 5/16″x1-1/4″ Hex Bolt 5/16″-18×7/8″
One-Piece Door with Track

Clevis Pin 5/16″x1″

19
o

Ring Fastener

Ring Fastener Nut 5/16″-18

Lock Washer 5/16″ -18

Clevis Pin 5/16″x1-1/4″
Hex Bolt 5/16″-18×7/8″

Clevis Pin 5/16″x1″

Installation
STEP 10 Install the door control

To prevent possible SERIOUS INJURY or DEATH from electrocution:
l Be sure power is NOT connected BEFORE installing door control. l Connect door control ONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
l Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.
l NEVER permit children to operate or play with door control push buttons or remote control transmitters.
l Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
l ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.
INTRODUCTION
Older Chamberlain door controls and third party products are not compatible. Install the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from the moving parts of the door. For gang box installations it is not necessary to drill holes or install the drywall anchors. Use the existing holes in the gang box.
Your product may look different than the illustrations.

Screw 6-32×1″ (2)

Drywall Anchors (2)

HARDWARE
Screw 6ABx1″ (2)

1. Strip 7/16 inch (11 mm) of insulation from one end of the wire and separate the wires. 2. Connect one wire to each of the two screws on the back of the door control. The wires can be
   connected to either screw. If your garage is pre-wired for the door control choose any two wires to connect, note which wires are used so the correct wires are connected to the garage door opener in a later step. 3. Mark the location of the bottom mounting hole and drill a 5/32 inch hole. 4. Install the bottom screw, allowing 1/8 inch (3 mm) to protrude from the wall. 5. Position the bottom hole of the door control over the screw and slide down into place. 6. Lift the push bar up and mark the top hole. 7. Remove the door control from the wall and drill a 5/32 inch hole for the top screw. 8. Position the bottom hole of the door control over the screw and slide down into place. Attach the top screw.

1

2

7/16″ (11 mm)

3 Wall

4-5 DRYWALL

GANG BOX

Drywall Anchor 6ABx1″

6-32×1″

7

8

6

DRYWALL

Drywall Anchor 6ABx1″

GANG BOX

6-32×1″

20
o

Installation

STEP 11 Wire the door control to the garage door opener
HARDWARE

Insulated Staple
(Not Shown)
1. Run the white and red/white wire from the door control to the garage door opener. Attach the wire to the wall and ceiling with the staple (not applicable for gang box or pre-wired installations). Do not pierce the wire with the staple as this may cause a short or an open circuit.
2. Strip 7/16 inch (11 mm) of insulation from the end of the wire near the garage door opener. 3. Connect the wire to the red and white terminals on the garage door opener. If your garage is
pre-wired make sure you use the same wires that are connected to the door control. To insert or release wires from the terminal, push in the tab with screwdriver tip.

1

2

7/16″ (11 mm)

STEP 12 Attach the warning labels
1. Attach the entrapment warning label on the wall near the door control with tacks or staples. 2. Attach the manual release/safety reverse test label in a visible location on the inside of the
garage door.

Staple

3

RED WHITE WHITE GREY

21
o

Installation
STEP 13 Install the Protector System®

Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversing sensor.
To prevent SERIOUS INJURY or DEATH from closing garage door:
l Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be disabled.
l Install the safety reversing sensor so beam is NO HIGHER than 6″ (15 cm) above garage floor.

IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSORS The safety reversing sensors must be connected and aligned correctly before the garage door opener will move in the down direction. The sending sensor (with an amber LED) transmits an invisible light beam to the receiving sensor (with a green LED). If an obstruction breaks the light beam while the door is closing, the door will stop and reverse to the full open position, and the garage door opener lights will flash 10 times. NOTE: For energy efficiency the garage door opener will enter sleep mode when the door is fully closed. The sleep mode shuts the garage door opener down until activated. The sleep mode is sequenced with the garage door opener light bulb; as the light bulb turns off the sensor LEDs will turn off and whenever the garage door opener lights turn on the sensor LEDs will light. The garage door opener will not go into the sleep mode until the garage door opener has completed 5 cycles upon power up. When installing the safety reversing sensors check the following:
l Sensors are installed inside the garage, one on either side of the door. l Sensors are facing each other with the lenses aligned and the receiving sensor lens does not
receive direct sunlight. l Sensors are no more than 6 inches (15 cm) above the floor and the light beam is
unobstructed.

Invisible Light Beam Protection Area

Safety Reversing Sensor 6″ (15 cm) max. above floor

Carriage Bolt 1/4″-20×1/2″

HARDWARE
Wing Nut 1/4″-20

The safety reversing sensors can be attached to the door track, the wall, or the floor. The sensors should be no more than 6 inches (15 cm) above the floor. If the door track will not support the sensor bracket a wall installation is recommended. Choose one of the following installations.
OPTION A DOOR TRACK INSTALLATION
1. Slide the curved arms of the sensor bracket around the edge of the door track. Snap into place so that the sensor bracket is flush against the track.
2. Slide the carriage bolt into the slot on each sensor. 3. Insert the bolt through the hole in the sensor bracket and attach with the wing nut. The lenses
on both sensors should point toward each other. Make sure the lens is not obstructed by the sensor bracket.

1

2

3

No more than 6 inches (15 cm)

Carriage Bolt 1/4″-20×1/2″

Wing Nut 1/4″-20

Facing the door from inside the garage

22
o

Installation

STEP 13 Install the Protector System® (continued)

OPTION B WALL INSTALLATION

If additional clearance is needed an extension bracket (not provided) or wood blocks can be used. Make sure each bracket has the same amount of clearance so they will align correctly.
1. Position the sensor bracket against the wall with the curved arms facing the door. Make sure there is enough clearance for the beam to be unobstructed. Mark holes.
2. Drill 3/16 inch pilot holes for each sensor bracket and attach the sensor brackets to the wall using lag screws (not provided).
3. Slide the carriage bolt into the slot on each sensor. 4. Insert the bolt through the hole in the sensor bracket and attach with the wing nut. The lenses
on both sensors should point toward each other. Make sure the lens is not obstructed by the sensor bracket.

1

(Not provided)

2

IGWnasariladl gee

(Not provided)

No more than 6 inches (15 cm)

3 Lens

4
Carriage Bolt 1/4″-20×1/2″

Wing Nut 1/4″-20

OPTION C FLOOR INSTALLATION

Use an extension bracket (not provided) or wood block to raise the sensor bracket if needed.
1. Carefully measure the position of both sensor brackets so they will be the same distance from the wall and unobstructed.
2. Attach the sensor brackets to the floor using concrete anchors (not provided). 3. Slide the carriage bolt into the slot on each sensor. 4. Insert the bolt through the hole in the sensor bracket and attach with the wing nut. The lenses
on both sensors should point toward each other. Make sure the lens is not obstructed by the sensor bracket.

1

2

(Not provided)

IGWnasarildal ege

3

4

Carriage Bolt 1/4″-20×1/2″

Wing Nut 1/4″-20

23
o

Installation

STEP 14 Wire the Safety Reversing Sensors

1

If your garage already has wires installed for the safety reversing sensors, proceed to page 25.

HARDWARE

2 Staple

Insulated Staple (Not Shown)
OPTION A INSTALLATION WITHOUT PRE-WIRING

1. Run the wire from both sensors to the garage door opener. Attach the wire to the wall and

ceiling with the staples.

2. Strip 7/16 inch (11 mm) of insulation from each set of wires. Separate the wires. Twist the white

wires together. Twist the white/black wires together.

3. Insert the white wires into the white terminal on the garage door opener. Insert the white/black

3

wires into the grey terminal on the garage door opener. To insert or remove the wires from the

terminal, push in the tab with a screwdriver tip.

7/16″ (11 mm)

RED WHITE WHITE GREY

24
o

Installation

STEP 14 Wire the Safety Reversing Sensors (continued) OPTION B PRE-WIRED INSTALLATION

1
Safety reversing sensor wires

2
Pre-installed wires

1. Cut the end of the safety reversing sensor wire, making sure there is enough wire to reach the

pre-installed wires from the wall.

2. Separate the safety reversing sensor wires and strip 7/16 inch (11 mm) of insulation from each

end. Choose two of the pre-installed wires and strip 7/16 inch (11 mm) of insulation from each

end. Make sure that you choose the same color pre-installed wires for each sensor.

3. Connect the pre-installed wires to the sensor wires with wire nuts making sure the colors correspond for each sensor. For example, the white wire would connect to the yellow wire and

3

the white/black wire would connect to the purple wire.

4. At the garage door opener, strip 7/16 inch (11 mm) of insulation from each end of the wires

previously chosen for the safety reversing sensors. Twist the like-colored wires together.

5. Insert the wires connected to the white safety sensor wires to the white terminal on the garage

door opener. Insert the wires that are connected to the white/black safety sensor wires to the

grey terminal on the garage door opener.

Safety reversing sensor wires
White White/Black

4

5

Yellow

Purple 7/16″ (11 mm)

RED WHITE WHITE GREY

7/16″ (11 mm)

Not Provided Pre-installed wires
Yellow (for example) Purple (for example)

Yellow (for example)

Purple (for
example)

To insert or remove the wires from the terminal, push in the tab with a screwdriver tip.

25
o

Installation
STEP 15 Connect power
To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: l Be sure power is NOT connected to the opener, and disconnect power to circuit BEFORE
removing cover to establish permanent wiring connection. l Garage door installation and wiring MUST be in compliance with ALL local electrical and
building codes. l NEVER use an extension cord, 2-wire adapter, or change plug in ANY way to make it fit outlet.
Be sure the opener is grounded.
To avoid installation difficulties, do not run the opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn’t fit into the outlet you have, contact a qualified electrician to install the proper outlet.

THERE ARE TWO OPTIONS FOR CONNECTING POWER:
OPTION A TYPICAL WIRING
1. Plug in the garage door opener into a grounded outlet. 2. DO NOT run garage door opener at this time.
OPTION B PERMANENT WIRING
If permanent wiring is required by your local code, refer to the following procedure. To make a permanent connection through the 7/8 inch hole in the top of the motor unit (according to local code):
1. Remove the motor unit cover screws and set the cover aside. 2. Remove the attached 3-prong cord. 3. Connect the black (line) wire to the screw on the brass terminal; the white (neutral) wire to the
screw on the silver terminal; and the ground wire to the green ground screw. The opener must be grounded. 4. Reinstall the cover.

Ground Tab
Green Ground Screw
Ground Wire
White Wire

Black Wire
Black Wire

26
o

Installation
STEP 16 Aligning the safety reversing sensors
The door will not close if the sensors have not been installed and aligned correctly. When the light beam is obstructed or misaligned while the door is closing, the door will reverse and the garage door opener lights will flash ten times. If the door is already open, it will not close.
1. Check to make sure the LEDs in both sensors are glowing steadily. The LEDs in both sensors will glow steadily if they are aligned and wired correctly.
The sensors can be aligned by loosening the wing nuts, aligning the sensors, and tightening the wing nuts.

IF THE AMBER LED ON THE SENDING SENSOR IS NOT GLOWING:
1. Make sure there is power to the garage door opener. 2. Make sure the sensor wire is not shorted/broken. 3. Make sure the sensor has been wired correctly: white wires to white terminal and white/black
wires to grey terminal.

1

2

3

RED WHITE WHITE GREY

If the receiving sensor is in direct sunlight, switch it with sending sensor so it is on the opposite side of the door.

IF THE GREEN LED ON THE RECEIVING SENSOR IS NOT GLOWING: 1. Make sure the sensor wire is not shorted/broken. 2. Make sure the sensors are aligned.

1

2

(invisible light beam)

Amber LED SENDING SENSOR

Green LED RECEIVING SENSOR

STEP 17 Ensure the door control is wired correctly
If the door control has been installed and wired correctly, a message will display on the Smart Control Panel screen.

27
o

Adjustments

Introduction
Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. l Incorrect adjustment of garage door travel limits will interfere with proper operation of safety
reversal system. l After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST
reverse on contact with 1-1/2″ (3.8 cm) high object (or 2×4 laid flat) on floor.

One-Piece Doors Only When setting the UP travel for a one-piece door ensure that the door does not slant backwards when fully open (UP). If the door is slanted backwards this will cause unnecessary bucking and/or jerking when the door is opening or closing.
CORRECT
INCORRECT

To prevent damage to vehicles, be sure fully open door provides adequate clearance.
Your garage door opener is designed with electronic controls to make setup and adjustments easy. The adjustments allow you to program where the door will stop in the open (UP) and close (DOWN) position. The electronic controls sense the amount of force required to open and close the door. The force is adjusted automatically when you program the travel.
NOTE: If anything interferes with the door’s upward travel it will stop. If anything interferes with the door’s downward travel, it will reverse.

Programming Buttons

The programming buttons are located on the left side panel of the garage door opener and are used to program the travel. While programming, the UP and DOWN buttons can be used to move the door as needed.

PROGRAMMING

UP Button

Adjustment Button

DOWN Button

UP (Open)

DOWN (Close)

To watch a short instructional video on programming your new garage door opener use your smartphone to read the QR Code below.

28
o

Adjustments
STEP 1 Program the Travel

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

l Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system.
l After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2″ (3.8 cm) high object (or 2×4 laid flat) on floor.
1 While programming, the UP and DOWN buttons can be used to move the door as needed.

1. Press and hold the Adjustment Button until the UP Button begins to flash and/or a beep is

heard.

2. Press and hold the UP Button until the door is in the desired UP position.
3. Once the door is in the desired UP position press and release the Adjustment Button. The

garage door opener lights will flash twice and the DOWN Button will begin to flash.

IMPORTANT NOTE: For one-piece door installations refer to page 28. 4. Press and hold the DOWN button until the door is in the desired DOWN position.

4

5. Once the door is in the desired DOWN position press and release the Adjustment Button. The

garage door opener lights will flash twice and the UP Button will begin to flash.

6. Press and release the UP Button. When the door travels to the programmed UP position, the

DOWN Button will begin to flash.

7. Press and release the DOWN Button. The door will travel to the programmed DOWN position.

Programming is complete.

6 * If the garage door opener lights are flashing 5 times during the steps for Program the Travel, the

programming has timed out. If the garage door opener lights are flashing 10 times during the steps for

Program the Travel, the safety reversing sensors are misaligned or obstructed (refer to page 27). When

the sensors are aligned and unobstructed, cycle the door through a complete up and down cycle using

the remote control or the UP and DOWN buttons. Programming is complete. If you are unable to

operate the door up and down, repeat the steps for Programming the Travel.

29
o

PROGRAMMING BUTTONS

UP Button Adjustment Button

DOWN Button

2

3

5

7

Adjustments
STEP 2 Test the Safety Reversal System

STEP 3 Test the Protector System®

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.
l Safety reversal system MUST be tested every month. l After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST
reverse on contact with 1-1/2″ (3.8 cm) high object (or 2×4 laid flat) on the floor.

1. With the door fully open, place a 1-1/2 inch (3.8 cm) board (or a 2×4 laid flat) on the floor, centered under the garage door.
   2. Press the remote control push button to close the door. The door MUST reverse when it makes contact with the board.
   If the door stops and does not reverse on the obstruction, increase the down travel (refer to Adjustment Step 1). Repeat the test. When the door reverses upon contact with the 1-1/2 inch board, remove the board and open/close the door 3 or 4 times to test the adjustment. If the garage door opener continues to fail the safety reversal test, call a trained door systems technician.

1

2

Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.
1. Open the door. Place the garage door opener carton in the path of the door. 2. Press the remote control push button to close the door. The door will not move more than an
inch (2.5 cm), and the garage door opener lights will flash 10 times.
The garage door opener will not close from a remote control if the LED in either safety reversing sensor is off (alerting you to the fact that the sensor is misaligned or obstructed). If the garage door opener closes the door when the safety reversing sensor is obstructed (and the sensors are no more than 6 inches [15 cm] above the floor), call for a trained door systems technician.

1

2

30
o

Battery Backup

STEP 1 Install the Battery
To reduce the risk of FIRE or INJURY to persons: l Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance. l Use ONLY Chamberlain part # 41A6357-1 for replacement battery. l DO NOT dispose of battery in fire. Battery may explode. Check with local codes for disposal
instructions.
ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery compartment. The battery backup allows access in and out of your garage, even when the power is out. The battery does not have to be fully charged to operate the garage door opener. When the garage door opener is operating on battery power, it will run slower and the battery status LED will glow solid orange, a beep will sound approximately every 2 seconds. The following features are unavailable when operating on battery power:
l Garage Door Opener Lights l Unattended close devices and features (e.g. MyQ® Smartphone Control and Timer-to-Close)
Battery Status LED 1. Unplug the garage door opener. 2. Open the light lens on the right side panel of the garage door opener. Use a Phillips head
screwdriver to remove the battery cover on the garage door opener. 3. Partially insert the battery into the battery compartment with the terminals facing out.

4. Connect red (+) and black (-) wires from the garage door opener to the corresponding terminals on the battery.
   5. Replace the battery cover. 6. Plug in the garage door opener. 7. Wait for the green Battery Status LED to start flashing before proceeding to test the battery.
   STEP 2 Test the Battery
   1. Unplug the garage door opener. The battery status LED will either glow solid orange indicating opener is operating on battery power or will flash indicating low battery power. NOTE: Make sure the garage door opener is unplugged.
   2. Open and close the door using the remote control or door control. The garage door opener may run slower if the battery is not fully charged. The battery will take 24 hours to fully charge.
   3. Plug in the garage door opener. Verify the battery status LED is flashing green, indicating the battery is charging.

1

2

3

Charge the Battery
The battery charges while the garage door opener is plugged into an electrical outlet. The battery requires 24 hours to fully charge. A fully charged battery supplies 12Vdc to the garage door opener for one to two days of normal operation during an electrical power outage. After the electrical power has been restored, the battery will recharge within 24 hours. The battery will last approximately 1 to 2 years with normal usage. To obtain maximum battery life and prevent damage, disconnect the battery when the garage door opener is unplugged for an extended period of time, such as a summer or winter home.

31

o

MyQ® Smartphone Control
Get Connected
…and control your garage door opener with the MyQ® App. You will need:
l A smartphone or tablet l Broadband Internet connection l A strong Wi-Fi signal in the garage, see page 3 l Password for your home network l MyQ® serial number located on the garage door opener

1. ACTIVATE “WI-FI LEARN” MODE
   Press and release the yellow LEARN button on the garage door opener 3 times. The garage door opener will beep once and a blue light will flash. You have 20 minutes to complete the connection process.

“beep”

Blue LED

3. CONNECT THE GARAGE DOOR OPENER TO YOUR HOME WI-FI NETWORK
   Launch the web browser (such as Safari or Chrome) on your mobile device and go to “setup.myqdevice.com”. Follow the on-screen prompts to add the garage door opener to your home Wi-Fi network.

ATT

9:25 PM

100%

http://setup.myqdevice.com

Welcome. This step-by-step guide will help you connect your Wi-Fi Garage Door Opener to the internet through your home’s Wi-Fi network.
Press Start to begin the process by scanning for available networks.
Start
About
Tap EXIT to reconnect your mobile device to your home’s Wi-Fi network.
Exit
©2014 The Chamberlain Group, Inc.

4. SETUP YOUR MyQ® ACCOUNT Download the MyQ® app from the App StoreSM or Google PlayTM store. Sign up for your MyQ® account and add the MyQ® serial number to your account.
   Google Play or
   App Store

5. CONNECT TO THE MyQ® Wi-Fi NETWORK On your mobile device, go to Settings > Wi-Fi, and select the network with the “MyQ-” prefix.

Congratulations you’ve successfully completed the setup. Enjoy MyQ® Smartphone Control!
In addition to controlling your garage door opener you can control your house lighting with additional MyQ® accessories, see page 41. NOTES: The MyQ® Smartphone Control WILL NOT work if the garage door opener is operating on battery power. To erase the Wi-Fi settings, see page 37.
To learn more go to wifihelp.chamberlain.com.
32

o

Operation

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or
   play with garage door control push buttons or remote controls. 3. ONLY activate garage door when it can be seen clearly, it is properly adjusted, and there are no
   obstructions to door travel. 4. ALWAYS keep garage door in sight and away from people and objects until completely closed.
   NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR. 5. NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY OPENED DOOR. 6. If possible, use emergency release handle to disengage trolley ONLY when garage door is
   CLOSED. Use caution when using this release with the door open. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly and increasing the risk of SEVERE INJURY or DEATH. 7. NEVER use emergency release handle unless garage doorway is clear of persons and obstructions. 8. NEVER use handle to pull garage door open or closed. If rope knot becomes untied, you could fall.

2. After ANY adjustments are made, the safety reversal system MUST be tested. 10. Safety reversal system MUST be tested every month. Garage door MUST reverse on contact
   with 1-1/2″ (3.8 cm) high object (or a 2×4 laid flat) on the floor. Failure to adjust the garage door opener properly increases the risk of SEVERE INJURY or DEATH. 11. ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED (see page 2). An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH. 12. ALL repairs to cables, spring assemblies and other hardware, ALL of which are under EXTREME tension, MUST be made by a trained door systems technician. 13. ALWAYS disconnect electric and battery power to garage door opener BEFORE making ANY repairs or removing covers. 14. This operator system is equipped with an unattended operation feature. The door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR. 15. DO NOT install on a one-piece door if using devices or features providing unattended close. Unattended devices and features are to be used ONLY with sectional doors.
   16. SAVE THESE INSTRUCTIONS.

33
o

Operation

Using your Garage Door Opener
l The garage door opener can be activated with a wall-mounted door control, remote control, wireless keyless entry, MyQ® Smartphone Control app or MyQ® Garage Door Monitor. When the door is closed and the garage door opener is activated the door will open. If the door senses an obstruction or is interrupted while opening the door will stop. When the door is in any position other than closed and the garage door opener is activated the door will close. If the garage door opener senses an obstruction while closing, the door will reverse. If the obstruction interrupts the sensor beam the garage door opener lights will blink 10 times. If the door is fully open, and the safety reversing sensors are not installed, or are misaligned, the door will not close from a remote control, TTC, or the MyQ® Smartphone Control app. However, you can close the door by holding the button on the door control or the ENTER button on the keyless entry until the door is fully closed.
l The garage door opener light bulbs will turn on when the opener is initially plugged in; power is restored after interruption, or when the garage door opener is activated. The lights will turn off automatically after 4-1/2 minutes. The lights will turn on when someone enters through the open garage door and the safety reversing sensor infrared beam is obstructed, see page 35. Use an incandescent A19 light bulb (100 watt maximum) or for maximum energy efficiency a 26W (100W equivalent) compact fluorescent light (CFL) bulb. NOTE: Do not use halogen, short neck, or specialty light bulbs as these may overheat the end panel or light socket. Do not use LED bulbs as they may reduce the range or performance of your remote controls.

To Open the Door Manually
To prevent possible SERIOUS INJURY or DEATH from a falling garage door: l If possible, use emergency release handle to disengage trolley ONLY when garage door is
CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly. l NEVER use emergency release handle unless garage doorway is clear of persons and obstructions. l NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall. DISCONNECT THE TROLLEY 1. The door should be fully closed if possible. 2. Pull down on the emergency release handle so the trolley release arm snaps to the vertical
position. The door can now be raised and lowered as often as necessary.

TO RE-CONNECT THE TROLLEY
1. Pull the emergency release handle toward the garage door opener so the trolley release arm snaps to the horizontal position. The trolley will reconnect on the next UP or DOWN operation, either manually or by using the door control or remote control.

34
o

Operation
Door Control
SYNCHRONIZE THE DOOR CONTROL: To synchronize the door control to the garage door opener, press the push bar until the garage door opener activates (it may take up to 3 presses). Test the door control by pressing the push bar; each press of the push bar will activate the garage door opener.

MENU OPTIONS

Push Bar

Screen
Navigation Buttons
Motion Sensor
LIGHT Button
PUSH BAR: Press the push bar to open or close the door.
LIGHT BUTTON: Press the LIGHT button to turn the garage door opener lights on or off. When the lights are turned on they will stay on until the LIGHT button is pressed again, or until the garage door opener is activated. Once the garage door opener is activated the lights will turn off after the specified period of time (the factory default is 4-1/2 minutes). The LIGHT button will not control the lights when the door is in motion. The Light Feature will turn on the light on the garage door opener when someone enters through the open garage door and the safety reversing sensor infrared beam is obstructed.
MOTION SENSOR: The motion sensor automatically turns on the garage door opener lights when motion is detected. The lights come on for the set period of time, and then shut off. If using the garage door opener light as a work light disable the motion sensor, otherwise the lights may turn off automatically if you are beyond the range of the motion sensor.
NAVIGATION AND SCREEN: The screen displays the time, temperature, and current battery charge (if applicable) until the menu button is pressed, and then it will display the menu options. If there is a problem with the garage doors opener the screen will display an error code (diagnostic code, see page 39). The features on the door control can be programmed through a series of menus on the screen. Use the navigation buttons to scroll through the menus and make selections.

CLOCK SETUP: Set the time; choose 12 or 24 hour clock and show/hide clock. TEMPERATURE: Display the temperature in Fahrenheit or Celsius and show/hide the temperature. LANGUAGE: Select English, Spanish or French. CONTRAST ADJUST: Adjust the screen contrast. LIGHT SETTINGS: To change the amount of time the lights stay on:
1. Select LIGHT SETTINGS from the menu. 2. Select LIGHT TIME. 3. Select the time interval.
To turn the Light Feature on or off (Factory default is On): 1. Select LIGHT SETTINGS from the menu. 2. Select AUTOMATIC LIGHTS. 3. Select ENTRY SENSOR.
To turn the motion sensor on or off: 1. Select LIGHT SETTINGS from the menu. 2. Select AUTOMATIC LIGHTS. 3. Select MOTION SENSOR.
LOCK: Prevents the garage door opener from being activated by remote controls while still allowing activation from the door control and keyless entry. To turn the LOCK feature ON or OFF:
1. Select LOCK from the menu. When the LOCK feature is on, a message displays on the screen.

35

o

Operation

MENU OPTIONS (CONTINUED)
TIMER-TO-CLOSE (TTC) (Factory default is set to off): The Timer-to-Close feature automatically closes the door after a specified time period and can be adjusted using the door control. DO NOT enable TTC if operating a one-piece door. TTC is to be used ONLY with sectional doors. The garage door opener will beep and the lights will flash before closing the door. The TTC feature will deactivate if the garage door encounters an obstruction twice; or the safety reversing sensors are incorrectly installed. The garage door will reverse open and WILL NOT close until the obstructions are clear or the safety reversing sensors are correctly installed. When the obstruction has been cleared or the safety reversing sensors have been aligned, the door will close when the garage door opener is activated. TTC WILL NOT work if the garage door opener is operating by battery power or if the safety reversing sensors are misaligned. This feature is NOT intended to be the primary method of closing the door. A keyless entry should be installed in the event of an accidental lock out when using this feature.
To turn TTC on or off or to set the TTC time interval:
1. Select TTC from the menu. 2. Select a time interval of 1, 5, 10 minutes or a custom setting up to 99 minutes. Once the TTC
has been set and the door is open, a message will display on the screen with the selected time interval.
To temporarily suspend the TTC feature select HOLD. Select REL to resume normal TTC operation. PROGRAM: Any compatible remote control, wireless keyless entry, or MyQ® devices can be programmed to the garage door using the PROGRAM option from the menu.

Remote Control and Keyless Entry
Your remote control has been programmed at the factory to operate with your garage door opener, randomly accessing over 100 billion new codes with each use. Your garage door opener can be programmed with up to 8 remote controls, 1 keyless entry, 2 Security+ 2.0® door controls and 6 MyQ® accessories. Older Chamberlain remote controls are NOT compatible, see page 41 for compatible accessories. Programming can be done through the door control or the learn button on the garage door opener. To program additional accessories refer to the instructions provided with the accessory or visit www.chamberlain.com. If your vehicle is equipped with HomeLink®, a Compatibility BridgeTM (not included) may be necessary for certain vehicles. Visit bridge.chamberlain.com to find out if a Bridge is needed. TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN USING THE DOOR CONTROL
1. Press the navigation button below “MENU” to view the Features menu. 2. Use the navigation buttons to scroll to “PROGRAM”. 3. Select “REMOTE” or “KEYPAD” to program from the program menu. 4. Remote Control: Press the button on the remote control that you wish to operate your garage
door. Keyless Entry: Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button.

The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed. Repeat the steps for programming additional remote controls or keyless entry devices. If programming is unsuccessful, repeat the steps using the learn button on the garage door opener.

1

2 Press to continue.

3 Press to continue.

4
36
o

OR
???? PIN

Operation
To Erase the Memory
ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES 1. Press and hold the LEARN button on garage door opener until the learn LED goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. Reprogram any accessory you wish to use.
ERASE ALL REMOTE CONTROLS, KEYLESS ENTRIES AND MyQ® DEVICES FROM GARAGE DOOR OPENER
1. Press and hold the LEARN button on garage door opener until the learn LED goes out (approximately 6 seconds).
2. Immediately press and hold the LEARN button again until the learn LED goes out. All codes are now erased. Reprogram any accessory you wish to use.
ERASE THE CONNECTION FROM GARAGE DOOR OPENER TO HOME Wi-Fi NETWORK
1. Press and hold the black adjustment button on the garage door opener until 3 beeps are heard (Approximately 6 seconds).
ERASE A MyQ® ACCOUNT 1. Go to www.mychamberlain.com to access your MyQ® account. 2. Go to “Account” section. 3. Click “Delete Account”.
Go to wifihelp.chamberlain.com for more details.
37
o

Maintenance

Maintenance Schedule
EVERY MONTH l Manually operate door. If it is unbalanced or binding, call a trained door systems technician. l Check to be sure door opens and closes fully. Adjust if necessary, see page 28. l Test the safety reversal system. Adjust if necessary, see page 30.
EVERY YEAR l Oil door rollers, bearings and hinges. The garage door opener does not require additional
lubrication. Do not grease the door tracks. l Test the battery backup and consider replacing the battery to ensure the garage door opener will
operate during an electrical power outage, see page 31 to test the battery backup.

The Remote Control Battery
To prevent possible SERIOUS INJURY or DEATH: l NEVER allow small children near batteries. l If battery is swallowed, immediately notify doctor. To reduce risk of fire, explosion or chemical burn: l Replace ONLY with 3V CR2032 coin batteries. l DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.

The 3V CR2032 Lithium battery should produce power for up to 3 years. If the battery is low, the remote control’s LED will not flash when the button is pressed.
To replace battery, pry open the case first in the middle (1), then at each side (2 and 3) with the visor clip. Replace the batteries with only 3V CR2032 coin cell batteries. Insert battery positive side up. Dispose of old batteries properly.

3
1 2

NOTICE: To complywith FCC and/or IndustryCanada (IC) rules, adjustment or modificationsof thistransceiver are prohibited. THERE ARENO USER SERVICEABLEPARTS. Thisdevice complieswith Part 15 of the FCC rulesand IC RSS-210. Operation issubject to the following two conditions: (1) thisdevice maynot cause harmfulinterference, and (2) thisdevice must accept anyinterference received, including interference that maycause undesired operation. Thisdevice must be installed in a waywhere a minimum8″(20 cm) distance ismaintained between users/bystandersand device. AVIS: Lesrèglesde la FCC et/ou d’Industrie Canada (IC) interdisent tout ajustement ou toute modification de ce récepteur. IL N’EXISTEAUCUNEPIÈCESUSCEPTIBLED’ÊTREENTRETENUEPAR L’UTILISATEUR. Cet appareilest conforme auxdispositionsde la partie 15 du règlement de la FCC et de l’norme IC RSS-210. Son utilisation est assujettie auxdeuxconditoinssuivantes: (1) ce dispositif ne peut causer desinterférencesnuisibles, et (2) ce dispositif doit accepter toute interférence recue, ycomprisune interférence pouvant causer un fonctionnement non souhaité. Cet appareildoit être installé de manière à laisser une distance d’au moins20 cm(8 po) entre celui-ciet l’utilisateur ou toute personne.

38
o

Troubleshooting

Diagnostic Chart
Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage door opener flash the diagnostic codes.

DIAGNOSTIC CODE

Up Arrow

Down Arrow

Flash(es)

Flash(es)

SYMPTOM

SOLUTION

1

1

The garage door opener will not close and the light bulbs flash.

Safety sensors are not installed, connected, or wires may be cut. Inspect sensor wires for a disconnected or cut wire.

1

2

The garage door opener will not close and the light bulbs flash.

There is a short or reversed wire for the safety sensors. Inspect safety sensor wire at all staple and connection points, replace wire or correct as needed.

1

3

The door control will not function.

The wires for the door control are shorted or the door control is faulty. Inspect door control wires at all staple and connection points, replace wire or correct as needed.

Safety sensors are misaligned or were momentarily obstructed. Realign both sensors to ensure both

1

4

The garage door opener will not close and the light bulbs flash. LEDs are steady and not flickering. Make sure nothing is hanging or mounted on the door that would

interrupt the sensor’s path while closing.

1

5

Door moves 6-8″ (15-20 cm) stops or reverses.

Manually open and close the door. Check for binding or obstructions, such as a broken spring or door lock, correct as needed. Check wiring connections at travel module and at the logic board. Replace travel module if necessary.

No movement, only a single click.

Manually open and close the door. Check for binding or obstructions, such as a broken spring or door lock, correct as needed. Replace logic board if necessary.

Opener hums for 1-2 seconds no movement.

Manually open and close the door. Check for binding or obstructions, such as a broken spring or door lock, correct as needed. Replace motor if necessary.

1

6

Door coasts after it has come to a complete stop.

Program travel to coasting position or have door balanced by a trained door systems technician.

2

1-5

No movement, or sound.

Replace logic board.

3

2

Unable to set the travel or retain position.

Check travel module for proper assembly, replace if necessary.

3

3

The battery status LED is constantly flashing green.

Battery backup charging circuit error, replace the logic board.

4

1-4

Door is moving stops or reverses.

Manually open and close the door. Check for binding or obstructions, such as a broken spring or door lock, correct as needed. If the door is binding or sticking contact a trained door systems technician. If door is not binding or sticking attempt to reprogram travel (refer to page 29).

4

5

Opener runs approximately 6-8″ (15-20 cm), stops and reverses. Communication error to travel module. Check travel module connections, replace travel module if

necessary.

39

o

Troubleshooting

DIAGNOSTIC CODE

Up Arrow Flash(es)

Down Arrow Flash(es)

4

6

SYMPTOM The garage door opener will not close and the light bulbs flash.

SOLUTION
Safety sensors are misaligned or were momentarily obstructed. Realign both sensors to ensure both LEDs are steady and not flickering. Make sure nothing is hanging or mounted on the door that would interrupt the sensor’s path while closing.

The garage door opener can beep for several reasons:

My vehicle’s Homelink® is not programming to my garage door opener:

l Operating on battery power or the 12 Vdc battery needs to be replaced, see page 31.

Compatibility BridgeTM (not included) may be necessary for certain vehicles. Visit

l Garage door opener has been activated through a device or feature such as Timer-to-Close or bridge.chamberlain.com to find out if a Bridge is needed.

garage door monitor, see page 34.

Wi-Fi troubleshooting

My remote control will not activate the garage door:

If your black adjustment button is not solid green go to wifihelp.chamberlain.com.

l l l

Verify the lock feature is not activated on the door control. Reprogram the remote control. If the remote control will still not activate the door check the diagnostic codes to ensure the garage door opener is working properly.

Green battery status LED – All systems are normal: l A solid green LED light indicates the battery is fully charged. l A flashing green LED indicates the battery is being charged.

My door will not close and the light bulbs blink on my motor unit:
The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction.
l Verify the safety sensors are properly installed, aligned and free of any obstructions.

Orange battery status LED – The garage door opener has lost power and is in battery backup mode:
l A solid orange LED with beep, sounding approximately every 2 seconds, indicates the garage door opener is operating on battery power.
l A flashing orange LED with beep, sounding every 30 seconds, indicates the battery is low.

My garage door opener light(s) will not turn off when the door is open:

Red battery status LED – The garage door opener’s 12V battery needs to be replaced:

The garage door opener is equipped with a feature that turns the light on when the safety reversing sensors have been obstructed or when the motion sensor on the door control detects movement in the garage. These features can be disabled using the door control, see page 35.

l A solid red LED with beep, sounding every 30 seconds, indicates the 12V battery will no longer hold a charge and needs to be replaced. Please call for replacement battery to allow your system to operate during a power outage.

My neighbor’s remote control opens my garage door:

Erase the memory from your garage door opener and reprogram the remote control(s).

Battery Status LED

The LEDs on the door control blink:

If you have a Smart Control Panel installed and the TTC is set to a custom time, press the ON button on the Premium Motion-Detecting Control Panel to set the time properly.

40
o

Accessories

8808CB

8 Foot (2.4 m) Rail Extension: To allow an 8 foot (2.4 m) door to open fully.

041A5281-1 Extension Brackets: (Optional) For safety reversing sensor installation onto the wall or floor.

953EV

Remote Control: Works with ALL Chamberlain openers from 1993-present. MyQ® compatible. Includes visor clip.

41A6357-1

Standby Power System Battery: Provides backup power to the garage door opener.

8810CB

10 Foot (3 m) Rail Extension: To allow a 10 foot (3 m) door to open fully.

CLLP1

Laser Parking Assistant: Park in the right spot every time! A laser beam is activated by your garage door opener and projected on to the dashboard of your vehicle to guide perfect parking.

940EV

956EV

Wireless Keypad: For use outside of the home to enable access to the garage using a 4-digit PIN. Works with ALL Chamberlain openers from 1993-present. MyQ® compatible.

AGDMEV

Garage Door Monitor: Monitor open/closed status for up to 4 MyQ® compatible garage door openers or gate operators and close them from anywhere in the home.

Keychain Remote Control: Works with ALL Chamberlain openers from 1993-present. MyQ® compatible. With key ring.

MyQ® Accessories
You can program up to 10 MyQ® accessories to your MyQ® account.

PILCEV

MyQ® Remote Lamp Control: Monitor and control this plug in lamp switch with the MyQ® Smartphone App.

WSLCEV

MyQ® Interior/Exterior Light Switch Monitor and control this wall light switch with the MyQ® Smartphone App.

CIGBU

41

MyQ® Internet Gateway: Offers longer range wireless signal than standard Wi- Fi. Plugs into your home router as an optional way to provide MyQ® Smartphone Control for your garage door opener and MyQ® light controls.

o

Warranty

STOP!
This garage door opener WILL NOT work until the safety reversing sensors are properly installed and aligned.
Contact Information
For installation and service information, please visit:
www.chamberlain.com/parts-and-support
If you are ordering a repair part please have the following information: part number, part name, and model number. Address repair parts orders to: The Chamberlain Group, Inc. 6050 S. Country Club Road Tucson, AZ 85706
Register your new garage door opener at www.prodregister.com/chamberlain

CHAMBERLAIN® LIMITED WARRANTY The Chamberlain Group, Inc.® (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally installed, that it is free from defects in materials and/or workmanship for a specific period of time as defined below (the “Warranty Period”). The warranty period commences from the date of purchase.

Parts 5 Years

Motor Lifetime

WARRANTY PERIOD

Accessories

Belt

1 year

Lifetime

Battery Backup 1 year

The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, and maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety. If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-9131, toll free, before dismantling this product. You will be advised of disassembly and shipping instructions when you call. Then send the product or component, pre-paid and insured, as directed to our service center for warranty repair. Please include a brief description of the problem and a dated proof- of-purchase receipt with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returned pre-paid. Defective parts will be repaired or replaced with new or factory rebuilt parts at Seller’s sole option. [You are responsible for any costs incurred in removing and/or reinstalling the product or any component .] ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE APPLICABLE LIMITED WARRANTY PERIOD SET FORTH ABOVE FOR THE RELATED COMPONENT(S), AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some States and Provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT OF CONSUMABLE ITEMS (E.G., BATTERIES IN REMOTE CONTROL TRANSMITTERS AND LIGHT BULBS), OR UNITS INSTALLED FOR NON-RESIDENTIAL USE. THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. THIS LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.
Some states and provinces do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific 42 legal rights, and you may also have other rights, which vary from state to state and province to province.

o

Repair Parts
Rail Assembly Parts
Description 1 Belt 2 Pulley 3 Master Link 4 Rail 5 Trolley Assembly 6 “U” Bracket
Not Shown Wear Pads Hardware Bag

Part Number 41A5250 144C54 4A1008 41A5665
41C5141-2 12D598-1
183A163 041A7920-2

1

2

3
4 5
6

Accessories

1

Description

Part Number

1 Smart Control Panel®

41A7305-1

2

2 Remote Control

953ESTD

Installation Parts

Description

Part Number

1 Curved Door Arm

178B35

2 Door Bracket with Clevis Pin and Fastener

41A5047-1

3 Emergency Release Rope and Handle

41A2828

4 Header Bracket with Clevis Pin and Fastener

41A5047-2

5 Remote Control Visor Clip

29B137

6 Safety Sensor Bracket

041A5266-3

7 Safety Sensor Kit Receiving and sending sensors with wire

41A5034

8 Straight Door Arm

178B34

9 White and Red/White Wire

41B4494-1

10 3V CR2032 Lithium Battery

10A20

11 Hanging Brackets

12B776

Not Shown

Owner’s Manual

114A4763

2 3

NOTICE
11

1 4
7
6

9 5
8

10

43
o

Repair Parts
Garage Door Opener Parts
3 8
4 9
6

1
5 7 10

2
3 4

Description 1 Sprocket and Sprocket Cover with Screws 2 End Panel with light socket 3 Light Lens
WD1000WF HD950WF LW9000WF 4 Light Socket 5 Transformer 6 Cover 7 Motor with Travel Module 8 End Panel for Receiver Logic Board with light socket 9 Receiver Logic Board 10 Travel Module

Part Number 041C1751
041D7639-1
041D7570 041D7572 041D7571 041C0279 041D0277-1 041D0614-23 041D8006-1 041D8214 050DCTWF 041D8071-4

114A4763F

© 2016, The Chamberlain Group, Inc. All Rights Reserved
Wi-Fi® is a registered trademark of Wi-Fi Alliance App Store is a service mark of Apple Inc. Google Play is a trademark of Google Inc.

References

• Works With Chamberlain
• Chamberlain | Garage Door Openers, Remotes and Parts
• Manual-Hub.com - Free PDF manuals!
• setup.myqdevice.com
• Chamberlain | Garage Door Openers, Remotes and Parts
• Home
• Welcome | Chamberlain
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>