myQ-G0303-SP Home Bridge User Guide: Installation & Safety Instructions
- June 5, 2024
- CHAMBERLAIN
Table of Contents
The myQ-G0303-SP Home Bridge User Guide provides installation and safety instructions for the myQ Home Bridge. The device is designed to be enabled only on a sectional door and should not be used with one-piece or swinging doors to reduce the risk of severe injury to persons. The product comes with a warning that it contains lead, which is known to cause cancer or birth defects, or other reproductive harm. The user guide emphasizes the importance of reading the instructions thoroughly before beginning installation and using the product only with door openers manufactured after 1993 that use photoelectric sensors located near the bottom of the door track. The device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs, and its operation is subject to specific conditions to avoid harmful interference. The user guide also provides tips for setting up and using the myQ Home Bridge, including keeping any existing myQ devices plugged in, not deleting existing devices from the myQ app, and checking the Wi-Fi signal strength in the garage before installation. For more information or assistance, users can visit LiftMaster’s website.
MYQ-G0303-SP myQ Home
Bridge User Guide
To reduce the risk of SEVERE INJURY to persons:
• DO NOT enable the myQ® Home Bridge if operating either one-piece or swinging
doors. To be enabled ONLY on a sectional door.
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer or birth defects, or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Read instructions thoroughly BEFORE beginning.
If using this product with residential door openers, the product must be used
only with door openers manufactured after 1993 that use photoelectric sensors
located near the bottom of the door track that does not change the state of
those photoelectric sensors to a low power mode.
NOTICE: This device complies with Part 15 of the FCC rules and Industry
Canada’s license-exempt RSSs.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Any
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device must be installed to ensure a minimum 20 cm (8 in.) distance is
maintained between users/ bystanders and the device.
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules and Industry Canada ICES
standard. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WHAT’S IN THE BOX
BEFORE YOU START, YOU MUST HAVE A…
Compatible device:
-
LiftMaster®, Chamberlain®, and Raynor® garage door openers with myQ® technology
-
Craftsman® garage door openers with Smart Control or AssureLink™ Connectivity
-
LiftMaster® and Chamberlain® versions of myQ Garage®, Smart Garage™ Hub, and Smart Garage™ Control|
TIPS -
Keep any existing myQ devices plugged in
-
Do not delete existing devices from the myQ app
-
To control this HomeKit-enabled accessory, iOS 10.0 or later is recommended
-
Watch set up videos at www.LiftMaster.com/myQSupport
myQ® APP
- Power the myQ Home Bridge by plugging it in. The blue LED will start blinking.
- Download the myQ app or open the app if it is already installed.
- Create an account or sign in.
- Press the “+” or “ ” icon and select myQ-nnn under Discovered Accessories/Devices.
INSTALL
-
Check the Wi-Fi signal in the garage, where the myQ Home Bridge will be mounted.
-
Make sure you have two or more Wi-Fi bars.
NOTE : If there are signal strength issues, please visit
https://www.LiftMaster.com/wifisupportvideos. -
Install the myQ Home Bridge on the ceiling near the garage door opener, or in a convenient location in the garage within the Wi-Fi range.
TIP: Wrap excess power adapter cable around the mounting bracket. -
Plug it in and make sure the green LED turns on solid.
-
Attach the warning label to the wall next to the door control.
Need Help?
Go to:
www.LiftMaster.com/myQSupport
Communication between iPhone, iPad, or iPod touch and the HomeKit-enabled myQ®
device is secured by HomeKit technology and Security+ 2.0®.
Controlling this HomeKit-enabled accessory automatically and away from home
requires an Apple TV with tvOS 10.0 or later or an iPad with iOS 10.0 or later
set up as a home hub.
© 2022, LiftMaster
All Rights Reserved
SPECIFICATION
Product Name
|
myQ-G0303-SP Home Bridge
---|---
Product Type
|
Garage door opener accessory
Compatibility
|
- LiftMaster, Chamberlain, and Raynor garage door openers with myQ technology
- Craftsman garage door openers with Smart Control or AssureLink Connectivity
- LiftMaster and Chamberlain versions of myQ Garage, Smart Garage Hub, and Smart Garage Control
Installation Requirements
|
- Sectional door only
- Door openers manufactured after 1993 that use photoelectric sensors located near the bottom of the door track
- Minimum 20 cm (8 in.) distance between users/bystanders and the device
- Wi-Fi signal strength in the garage
Warnings
|
- Contains lead, which is known to cause cancer or birth defects, or other reproductive harm
- Do not enable with one-piece or swinging doors
Compliance
|
- Part 15 of the FCC rules
- Industry Canada’s license-exempt RSSs
Operation Requirements
|
- Avoid harmful interference
- Accept any interference received
Additional Information
|
- Keep any existing myQ devices plugged in
- Do not delete existing devices from the myQ app
- iOS 10.0 or later recommended for HomeKit-enabled accessory control
- Visit LiftMaster’s website for more information or assistance
FAQS
What should users do if they need help with the myQ Home Bridge?
Users can visit LiftMaster’s website for more information or assistance.
What is the recommended iOS version for controlling the HomeKit-enabled
accessory?
To control this HomeKit-enabled accessory, iOS 10.0 or later is recommended.
What are the tips for setting up and using the myQ Home Bridge?
The tips include keeping any existing myQ devices plugged in, not deleting existing devices from the myQ app, and checking the Wi-Fi signal strength in the garage before installation.
What type of door openers is the myQ Home Bridge compatible with?
If using this product with residential door openers, the product must be used only with door openers manufactured after 1993 that use photoelectric sensors located near the bottom of the door track that does not change the state of those photoelectric sensors to a low power mode.
What is the warning regarding the myQ Home Bridge product?
The product comes with a warning that it contains lead, which is known to cause cancer or birth defects, or other reproductive harm.
What type of doors is the myQ Home Bridge designed to be enabled on?
The myQ Home Bridge is designed to be enabled only on a sectional door and should not be used with one-piece or swinging doors to reduce the risk of severe injury to persons.