CHIEF SLB-354 Interface Brackets Instruction Manual

: June 17, 2024
: Chief

Table of Contents

CHIEF SLB-354 Interface Brackets
Product Information
Product Usage Instructions
FAQ
INSTALLATION INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CHIEF SLB-354 Interface Brackets

CHIEF-SLB-354-Interface-Brackets-product

Product Information

Specifications

Interface Brackets : SSB-354, SSM-354, SLB-354, and SLM-354
Hardware included :
- 1 Interface Bracket
- 4 Screw, Phillips Flat Head, Machine, M4 x 16mm
- 4 10-24 Thumb Nuts
- 4 Spacer, Nylon, .500 x .194 x .375
- 1 All-Points Security Kit
- 1 5/32 Security Hex Key

Product Usage Instructions

Installation Instructions

WARNING: Improper installation can lead to equipment falling causing serious personal injury and damage to equipment. DO NOT substitute hardware. Use only hardware suppliedby the manufacturer.

Note: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB- styland SSM-style interface bracket installation.

Step 1: Screw thumb screws onto 10-24 x 5/8 Phillips pan head screws. DO NOT fully tighten thumb screws at this time.

Step 2: Turn the projector upside down on a flat surface.

Step 3: Place four nylon spacers over threaded inserts in the bottom of the projector.

Step 4: Place the interface bracket onto the spacers and the bottom of the projector, aligning the mounting holes in the bracket with the spacers and threaded inserts. Ensure that the triangle in the bracket points towards the front of the projector.

Step 5: Position M4 x 16mm mounting screws into the interface bracket, nylon spacers, and threaded inserts. Tighten all fasteners at this time, securing the bracket to the projector.

Note: Security screws can be substituted when mounting the interface bracket to the projector by using the parts and installation instructions in the All-Points Security Kit.

FAQ

1. Can I use my own hardware for installation?
- No, it is important to use only the hardware supplied by the manufacturer to ensure proper installation and avoid any risks of equipment falling or damage.
2. What should I do if I have an SLB/SSB interface bracket?
- If you have an SLB/SSB interface bracket, follow Step 1 in the installation instructions. If you have an SLM/SSM bracket, proceed directly to Step 2.
3. Can I substitute security screws for mounting?
- Yes, you can substitute security screws for mounting the interface bracket to the projector by using the parts and installation instructions in the All-Points Security Kit.

INSTALLATION INSTRUCTIONS

SSB-354, SSM-354, SLB-354, and SLM-354 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific installation instructions provided with the mount for additional installation information.
Unpack cartons and verify the kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.

WARNING : IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by the manufacturer!

(1) Interface Bracket
(4) 10-24 Thumb Nuts
(1) All-Points Security Kit
(4) Screw, Phillips Flat Head, Machine, M4 x 16mm
(4) Spacer, Nylon, .500 x .194 x .375″
(1) 5/32″ Security Hex Key

CHIEF-SLB-354-Interface-Brackets-fig1

Only used when installing SLB/SSB interface brackets.
NOTE : Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above.
DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.
WARNING : OVER-TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT over-tighten screws when installing interface brackets.
NOTE : Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

Screw thumb screws onto 10-24 x 5/8″ Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
Turn the projector upside down on a flat surface.
Place four nylon spacers over threaded inserts in the bottom of the projector.
Place the interface bracket onto the spacers and bottom of the projector, aligning the mounting holes in the bracket with the spacers and threaded inserts and ensuring that the triangle in the bracket points towards the front of the projector.
Position M4 x 16mm mounting screws into the interface bracket, nylon spacers, and the threaded inserts. Tighten all fasteners at this time, securing the bracket to the projector.

NOTE : Security screws can be substituted when mounting the Interface bracket to the projector by using the parts and installation instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation or warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief, a products division of Milestone AV Technologies 6436 City West Parkway, Eden Prairie, MN 55344