Convair CTH01 Ceramic Fan Heater Instruction Manual

June 17, 2024
Convair

PORTABLE CERAMIC FAN HEATER
OWNER’S INSTRUCTION MANUAL
MODEL CTH01

SAFETY

GENERALSAFETY
Please read these instructions before using the heater and keep for future reference. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction in using the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance. Do not poke anything through the ventilating slits. Always use the heater in an upright position. Stand it on a firm, solid, horizontal base (not on thick pile carpets).
WARNING: In order to avoid overheating, do not cover the heater.
Leave nothing hanging above or in front of the heater (e.g. clothes or fabrics). Be sure that the air inlets and outlets on the heater are uncovered otherwise it will overheat.
Clean these openings at regular intervals to prevent airflow reduction (refer Maintenance section).
Do not use this heater outdoors, or on wet surfaces.
The heater outlet is hot when in use. To avoid burns, keep bare skin away from the outlets. Leave plenty of room around the heater (at least 50 cm on top and round the sides, 120 cm at the front).
ELECTRICALSAFETY
Connect the heater to a single 230 V, 10A socket only. Do not plug into double adaptors or multi-outlet power boards.
Make sure that the heater never comes into contact with water.
Never position the heater under a power outlet.
Never turn the heater on if the lead is damaged or if the heater’s casing is obviously damaged. In order to avoid a hazard, the power cord must be replaced by a licensed electrician or service agent. Do not pull the heater along by the power cord or place the cord near the hot air outlet. Always uncoil the power cord completely.
Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool. If the heater is to be used in a bathroom, ensure that switches and other controls cannot be touched by a person in the bath or shower.
Always turn the heater off and unplug from the power socket when not in use.
SAFETYDEVICES
To avoid overheating problems the in-built safety device will interrupt electricity if the heating elements become too hot.
If this should happen:

  • Take the plug out of the mains socket.
  • Let the heater cool down for 10 minutes.
  • Check that the heater is positioned correctly.
  • See that there is no dust or other obstacles hindering the air flow.
  • Clean the inlet& outlet grilles if necessary.

The heater is also equipped with a ‘tip-over’ switch, which will turn off power to the heater elements if it should fall over.

OPERATION

COMPONENT LIST A……………………..POWER BUTTON
B…………………….CONTROL PANEL
C ……………………POWER INDICATOR
D…………………… AIR INLET (REAR)
E …………………………AIR OUTLET
F…………………… BASE OPERATION
The Convair fan heater is excellent in providing spot heating throughout your home. It should not be considered as a centralized heating unit for your whole house.
TURNING THE POWER ON

  • Insert the plug into the power outlet.
  • Turn the heater ON by pushing the “ON/OFF” button on the unit (see Fig 1). The button will be lower when depressed and the FAN will start operating.
  • Press one of the “1000W” heater buttons. The heater will operate on LOW HEAT setting.
  • Press the second “1000W” heater button. The heater will operate on HIGH HEAT setting. Press one or both of the “1000W” buttons again to revert back to LOWHEAT or FAN modes.
  • Press the “ON/OFF” button to turn the heater off. This can be done on any setting and will return to these settings when switched back on.

OSCILLATION FUNCTION
Press the “ TURN ” button on the control panel to turn oscillation on. The heater will swing from side to side in a 90° arc. Press again to stop oscillating.

MAINTENANCE

MAINTENANCE
To maximise the efficiency of the heater, clean the inlet and outlet grilles regularly.

  • Unplug the heater from the mains power supply before cleaning.
  • Use a soft, damp cloth to wipe the outside. Never use thinners or other strong chemicals on the heater surfaces.
  • Use a vacuum cleaner to remove dirt and dust from the inlet and outlet grilles.
  • Ensure the heater is dry before plugging back into the mains power supply.

Waste electrical products must not be disposed of with household waste. This product should be taken to your local recycling centre for safe treatment.
As the policy of this company is one of continuous improvement, all specifications are subject to change without notice.
It is the policy of Seeley International to introduce continual product improvement. Accordingly, specifications are subject to change without notice. Please consult with your dealer to confirm the specifications of the model selected.

Service
Australia 1-300-650-399
seeleyinternational.com
convair.net.au
https://manual-hub.com/

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals