Indesit Washing Machine Manual: Install & Level Your IWC 5125

The Indesit Washing Machine Instruction Manual provides detailed information on how to install and operate the IWC 5125 washing machine. The manual emphasizes the importance of keeping it in a safe place for future reference, especially if the machine is sold or moved. The manual provides step-by-step instructions on how to unpack and level the machine, connect the electricity and water supplies, and run the first wash cycle. The manual also includes technical data, care and maintenance instructions, precautions, and tips to ensure safe and efficient use of the machine. The manual warns against using second-hand hoses, leaving the machine exposed to weather conditions, and attempting to repair the machine’s internal mechanisms. The manual also provides guidance on the correct disposal of old household electrical appliances in compliance with European regulations. Overall, the Indesit Washing Machine Instruction Manual is a valuable resource for anyone who wants to install and use the IWC 5125 washing machine safely and effectively.

Indesit Washing Machine Instruction Manual

Indesit Washing Machine Instruction Manual

Installation

! This instruction manual should be kept in a safe place for future reference. If the washing machine is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/herself with its operation and features. ! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging. 2. Make sure that the washing machine has not been damaged during the transportation process. If it has been damaged, contact the retailer and do not proceed any further with the installation process. 3. Remove the 3 protective screws (used during transportation) and the rubber washer with the corresponding spacer, located on the rear part of the appliance (see figure). 4. Close off the holes using the plastic plugs provided. 5. Keep all the parts in a safe place: you will need them again if the washing machine needs to be moved to another location. ! Packaging materials should not be used as toys for children.

Levelling

1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or anything else. 2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured in relation to the worktop, must not exceed 2°. Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting while it is operating. If it is placed on carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the washing machine.

Connecting the electricity and water supplies

Connecting the water inlet hose

 1. Connect the supply pipe by screwing it to a cold water tab using a ¾ gas threaded connection (see figure). Before performing the connection, allow the water to run freely until it is perfectly clear. 2. Connect the inlet hose to the washing machine by screwing it onto the corresponding water inlet of the appliance, which is situated on the top righthand side of the rear part of the appliance (see figure). 3. Make sure that the hose is not folded over or bent. ! The water pressure at the tap must fall within the values indicated in the Technical details table (see next page). ! If the inlet hose is not long enough, contact a specialised shop or an authorised technician. ! Never use second-hand hoses. ! Use the ones supplied with the machine.

Connecting the drain hose

Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor;   alternatively, rest it on the side of a washbasin or bathtub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater. ! We advise against the use of hose extensions; if it is absolutely necessary, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity socket, make sure that:

• the socket is earthed and complies with all applicable laws;
• the socket is able to withstand the maximum power load of the appliance as indicated in the Technical data table (see opposite);
• the power supply voltage falls within the values indicated in the Technical data table (see opposite);
• the socket is compatible with the plug of the washing machine. If this is not the case, replace the socket or the plug.

! The washing machine must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to rain, storms and other weather conditions. ! When the washing machine has been installed, the electricity socket must be within easy reach. ! Do not use extension cords or multiple sockets. ! The cable should not be bent or compressed. ! The power supply cable must only be replaced by authorised technicians. Warning! The company shall not be held responsible in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, using the wash cycle 2.

Technical data

Model| IWC 5125
Dimensions| width 59.5 cm height 85 cm depth 52.5 cm
Capacity| from 1 to 5 kg
Electrical connections| please refer to the technical data plate fixed to the machine
Water connection| maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capacity 46 litres
Spin speed| up to 1200 rotations per minute
Test wash cycles in accordance with directives 1061/2010 and 1015/2010.| Programme 3: Cotton standard 60°C; Programme 4: Cotton standard 40°C.
| This appliance conforms to the following EC Directives: – 2004/108/CE (Electromagnetic Compatibility) – 2002/96/EC – 2006/95/EC (Low Voltage)

3

Care and maintenance

Cutting off the water and electricity supplies

• Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washing machine and help to prevent leaks.
• Unplug the washing machine when cleaning it and during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

Remove the dispenser by raising it and pulling it out (see figure). Wash it under running water; this operation should be repeated frequently.

Caring for the door and drum of your appliance

• Always leave the porthole door ajar in order to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump which does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber which protects the pump, situated in its bottom part. ! Make sure the wash cycle has finished and unplug the appliance. To access the pre-chamber:  1. using a screwdriver, remove the cover panel on the lower front part of the washing machine (see figure);   2. unscrew the lid by rotating it anti-clockwise (see figure): a little water may trickle out. This is perfectly normal;   3. clean the inside thoroughly; 4. screw the lid back on; 5. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any cracks, it should be replaced immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open. ! Never use second-hand hoses.

4

Precautions and tips

! This washing machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully.

General safety

• This appliance was designed for domestic use only.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Do not touch the machine when barefoot or with wet or damp hands or feet.
• Do not pull on the power supply cable when unplugging the appliance from the electricity socket. Hold the plug and pull.
• Do not open the detergent dispenser drawer while the machine is in operation.
• Do not touch the drained water as it may reach extremely high temperatures.
• Never force the porthole door. This could damage the safety lock mechanism designed to prevent accidental opening.
• If the appliance breaks down, do not under any circumstances access the internal mechanisms in an attempt to repair it yourself.
• Always keep children well away from the appliance while it is operating.
• The door can become quite hot during the wash cycle.
• If the appliance has to be moved, work in a group of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy.
• Before loading laundry into the washing machine, make sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local regulations so that the packaging may be re-used.
• The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment, requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected.

Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

Description of the washing machine and starting a wash cycle

Control panel

Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”). ON/OFF button: switches the washing machine on and off. WASH CYCLE knob: programmes the wash cycles. During the wash cycle, the knob does not move. FUNCTION buttons with indicator light: used to select the available functions. The indicator light corresponding to the selected function will remain lit. TEMPERATURE knob: sets the temperature or the cold wash cycle (see “Personalisation”). SPIN SPEED knob: sets the spin speed or exclude the spin cycle completely (see “Personalisation”). WASH CYCLE PROGRESS/DELAY TIMER indicator lights: used to monitor the progress of the wash cycle. The illuminated indicator light shows which phase is in progress. If the Delay Timer function has been set, the time remaining until the wash cycle starts will be indicated (see next page). DOOR LOCKED indicator light: indicates whether the door may be opened or not (see next page). START/PAUSE button with indicator light: starts or temporarily interrupts the wash cycles. N.B. To pause the wash cycle in progress, press this button; the corresponding indicator light will flash orange, while the indicator light for the current wash cycle phase will remain lit in a fixed manner. If the DOOR LOCKED **indicator light is switched off, the door may be opened. To start the wash cycle from the point at which it was interrupted, press this button again. Standby mode** This washing machine, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled after a few minutes if no activity is detected. Press the ON-OFF button briefly and wait for the machine to start up again. Consumption in off- mode: 0,5 W Consumption in Left-on: 0,5

Indicator lights

The indicator lights provide important information. This is what they can tell you: Delayed start If the DELAY TIMER function has been activated (see “Personalisation”), after the wash cycle has been started the indicator light corresponding to the selected delay period will begin to flash: 3h 6h            9h           12h           As time passes, the remaining delay will be displayed and the corresponding indicator light will flash: 3h          6h            9h           12h The set programme will start once the selected time delay has expired. Wash cycle phase indicator lights Once the desired wash cycle has been selected and has be-gun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress. Wash            Rinse Spin                      Drain                    End of wash cycle END Function buttons and corresponding indicator lights When a function is selected, the corresponding indicator light will illuminate. If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and the function will not be activated. If the selected function is not compatible with another function which has been selected previously, the indicator light corresponding to the first function selected will flash and only the second function will be activated; the indicator light corresponding to the enabled option will remain lit. Door locked indicator light When the indicator light is on, the porthole door is locked to prevent it from being opened; make sure the indicator light is off before opening the door (wait approximately 3 minutes). To open the door during a running wash cycle, press the START/PAUSE button; the door may be opened once the DOOR LOCKED indicator light turns off.

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then they will switch off and the START/PAUSE indicator light will pulse. 2. Load the laundry and close the door. 3. Set the WASH CYCLE knob to the desired programme. 4. Set the washing temperature (see “Personalisation”). 5. Set the spin speed (see “Personalisation”). 6. Measure out the detergent and washing additives (see “Detergents and laundry”). 7. Select the desired functions. 8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed manner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle. 9. At the end of the wash cycle the END indicator light will switch on. The door can be opened once the DOOR LOCKED **** indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch the washing machine off by pressing the ON/OFF button.

Wash cycles

Table of wash cycles

Wash cycles| Description of the wash cycle| Max. temp. (°C)| Max. speed (rpm)|

Detergents

| Max. load (kg)| Residual dampness %| Energy consumption kWh| Total water lt| Cycle duration
---|---|---|---|---|---|---|---|---|---
Prewash| Wash| Fabric softener| Bleach
Daily
1| Cotton with prewash: extremely soiled whites.| 90°| 1200|

•

| •| •|

–

| 5| 53| 1,76| 61| 145’
2| Cotton: extremely soiled whites.| 90°| 1200|

–

| •| •|

•

| 5| 53| 1,70| 55| 130’
3| Cotton Standard 60° (1): heavily soiled whites and resistant colours.| 60°| 1200|

–

| •| •|

•

| 5| 53| 0,87| 47| 165’
4| Cotton Standard 40° (2): lightly soiled whites and delicate colours.| 40°| 1200|

–

| •| •|

•

| 5| 53| 1,09| 92| 155’
5| Coloured Cottons: lightly soiled whites and delicate colours.| 40°| 1200|

–

| •| •|

•

| 5| 53| 0,75| 50| 85’
6| Synthetics: heavily soiled resistant colours.| 60°| 800|

–

| •| •|

•

| 3| 44| 0,78| 33| 105’
6| Synthetics (3): lightly soiled resistant colours.| 40°| 800|

–

| •| •|

•

| 3| 44| 0,49| 32| 95’
7| Cotton Standard 20°: lightly soiled whites and delicate colours.| 20°| 1200|

–

| •| •|

•

| 5|

–

|

–

|

–

| 170’
Special
8| Wool: for wool, cashmere, etc.| 40°| 800|

–

| •| •|

–

| 1,5|

–

|

–

|

–

| 70’
9| Silk/Curtains: for garments in silk and viscose, lingerie.| 30°| 0|

–

| •| •|

–

| 1|

–

|

–

|

–

| 55’
10| Jeans| 40°| 800|

–

| •| •|

–

| 3|

–

|

–

|

–

| 60’
11| Express: to refresh lightly soiled garments quickly (not suitable for wool, silk and clothes which require washing by hand).| 30°| 800|

–

| •| •|

–

| 1,5| 71| 0,12| 27| 15’
Sport
12| Sport Intensive| 30°| 600|

–

| •| •|

–

| 3|

–

|

–

|

–

| 85’
13| Sport Light| 30°| 600|

–

| •| •|

–

| 3|

–

|

–

|

–

| 60’
14| Special Shoes| 30°| 600|

–

| •| •|

–

| Max. 2 pairs|

–

|

–

|

–

| 55’
Partial wash cycles
| Rinse|

–

| 1200|

–

| –| •|

•

| 5|

–

|

–

|

–

| 36’

| Spin + Drain|

–

| 1200|

–

| –| –|

–

| 5|

–

|

–

|

–

| 16’

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected. 1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 60°C. This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value. 2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 4 with a temperature of 40°C. This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value. For all Test Institutes: 2) Long wash cycle for cottons: set wash cycle 4 with a temperature of 40°C. 3) Long wash cycle for synthetics: set wash cycle 6; with a temperature of 40°C. Cotton Standard 20° (wash cycle 7 ) ideal for heavily soiled cotton loads. The effective performance levels achieved at cold temperatures, which are comparable to washing at 40°, are guaranteed by a mechanical action which operates at varying speed, with repeated and frequent peaks. Express (wash cycle 11 ) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and therefore saves both energy and time. By selecting this wash cycle ( 11 at 30°C), it is possible to wash different fabrics together (except for wool and silk items), with a maximum load of 1,5 kg. Sport Intensive (wash cycle 12 ) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. Sport Light (wash cycle 13 ) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a liquid detergent and dosage suitable for a half- load. Special Shoes (wash cycle 14 ) is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.

Personalization

Setting the temperature Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles). The temperature may be lowered, or even set to a cold wash . The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value set for each wash cycle. Setting the spin speed Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle. The maximum spin speeds available for each wash cycle are as follows: Wash cycles        Maximum spin speed Cottons                1200 rpm Synthetics             800 rpm Wool 800 rpm Silk                      drain only The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol . The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed set for each wash cycle. Functions The various wash functions available with this washing machine will help to achieve the desired results, every time. To activate the functions: 1. Press the button corresponding to the desired function; 2. the function is enabled when the corresponding indicator light is illuminated. Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the selected wash cycle. Ec Time Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled cotton and synthetic fabrics (refer to the “Table of wash cycles”). “ Ec Time ” enables you to wash in less time thereby saving water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity. ! This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, 14,  , . Stain removal Bleaching cycle designed to remove the toughest stains. Please remember to pour the bleach into extra compartment 4 (see “Bleach cycle”). ! This function may not be used in conjunction with wash cycles 1, 8, 9, 10, 11, 12, 13, 14, .   Extra rinse By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly useful for sensitive skin. ! This function may not be used in conjunction with wash cycles 11, .   Delay timer This timer delays the start time of the wash cycle by up to 12 hours. Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button is pressed, the function will be disabled. N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching the set programme. ! This option is enabled with all programmes.

Detergents and laundry

Detergent dispenser drawer Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause build up on the inside of your appliance and contribute to environmental pollution. ! Do not use hand washing detergents because these create too much foam. ! Use powder detergent for white cotton garments, for pre-washing, and for washing at temperatures over 60°C. ! Follow the instructions given on the detergent packaging. Open the detergent dispenser drawer and pour in the detergent or washing additive, as follows.   compartment 1: Pre-wash detergent (powder) Before pouring in the detergent, make sure that extra compartment 4 has been removed. compartment 2: Detergent for the wash cycle (powder or liquid) Liquid detergent should only be poured in immediately prior to the start of the wash cycle. compartment 3: Additives (fabric softeners, etc.) The fabric softener should not overflow the grid. extra compartment 4: Bleach Bleach cycle ! Traditional bleach should be used on sturdy white fabrics, and delicate bleach for coloured fabrics, synthetics and for wool. This option is particularly useful for the removal of stubborn stains. Place extra compartment 4 (supplied) into compartment 1. When pouring in the bleach, be careful not to exceed the “ max ” level marked on the central pivot (see figure). To run the bleach cycle on its own, pour the bleach into extra compartment 4 , set the “Rinse” programme and activate the “Stain removal” option. To bleach during a wash cycle, pour in the detergent and any fabric softener you wish to use, set the desired wash cycle and enable the “Stain removal” option. The use of extra compartment 4 excludes the “Pre-wash” option.

Preparing the laundry

• Divide the laundry according to: – the type of fabric/the symbol on the label – the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the listed values, which refer to the weight of the laundry when dry: see “Table of wash cycles”.

How much does your laundry weigh?

1 sheet 400-500 g 1 pillow case 150-200 g 1 tablecloth 400-500 g 1 bathrobe 900-1200 g 1 towel 150-250 g

Garments requiring special care Wool: all wool garments can be washed using programme 8 , even those carrying the “hand-wash only” label. For best results, use special detergents and do not exceed 1,5 kg of laundry. Silk: use special wash cycle 9 to wash all silk garments. We recommend the use of special detergent which has been designed to wash delicate clothes. Curtains: fold curtains and place them in a pillow case or mesh bag. Use wash cycle 9. Jeans: Turn garments inside-out before washing and use a liquid detergent. Use programme 10. Load balancing system Before every spin cycle, to avoid excessive vibrations and to distribute the load in a uniform manner, the drum rotates continuously at a speed which is slightly greater than the washing rotation speed. If, after several attempts, the load is not balanced correctly, the machine spins at a reduced spin speed. If the load is excessively unbalanced, the washing machine performs the distribution process instead of spinning. To encourage improved load distribution and balance, we recommend small and large garments are mixed in the load.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be not solved easily using the following list.

into the socket fully, or is not making contact. • There is no power in the house.
The wash cycle does not start.| • The washing machine door is not closed properly. • The ON/OFF button has not been pressed. • The START/PAUSE button has not been pressed. • The water tap has not been opened. • A delayed start has been set (see “Personalisation”).
The washing machine does not take in water (the indicator light for the first wash cycle stage flashes rapidly).| • The water inlet hose is not connected to the tap. • The hose is bent. • The water tap has not been opened. • There is no water supply in the house. • The pressure is too low. • The START/PAUSE button has not been pressed.
The washing machine continuously takes in and drains water.| • The drain hose is not fitted at a height between 65 and 100 cm from the floor (see “Installation”). • The free end of the hose is under water (see “Installation”). • The wall drainage system is not fitted with a breather pipe. If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the Assistance Service. If the dwelling is on one of the upper floors of a building, there may be problems relating to water drainage, causing the washing machine to fill with water and drain continuously. Special anti-draining valves are available in shops and help to avoid this inconvenience.
The washing machine does not drain or spin.| • The wash cycle does not include draining: some wash cycles require the drain phase to be started manually. • The drain hose is bent (see “Installation”). • The drainage duct is clogged.
The washing machine vibrates a lot during the spin cycle.| • The drum was not unlocked correctly during installation (see “Installation”). • The washing machine is not level (see “Installation”). • The washing machine is trapped between cabinets and walls (see “Installation”).
The washing machine leaks.| • The water inlet hose is not screwed on properly (see “Installation”). • The detergent dispenser drawer is blocked (for cleaning instructions, see “Care and maintenance”). • The drain hose is not fixed properly (see “Installation”).
The “option” indicator lights and the “start/pause” indicator light flash, while one of the “phase in progress” indicator lights and the “door locked” indicator light will remain lit in a fixed manner. **| • Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again. If the problem persists, contact the Technical Assistance Service.
There is too much foam.**| • The detergent is not suitable for machine washing (it should display the text “for washing machines” or “hand and machine wash”, or the like). • Too much detergent was used.

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);
• Restart the programme to check whether the problem has been solved;
• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N). This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the front of the appliance by opening the door.

SPECIFICATION

Model

|

IWC 5125

---|---

Dimensions

|

width 59.5 cm, height 85 cm, depth 52.5 cm

Capacity

|

from 1 to 5 kg

Electrical connections

|

please refer to the technical data plate fixed to the machine

Water connection

|

maximum pressure 1 MPa (10 bar), minimum pressure 0.05 MPa (0.5 bar), drum capacity 46 litres

Spin speed

|

up to 1200 rotations per minute

Test wash cycles

|

Programme 3: Cotton standard 60°C; Programme 4: Cotton standard 40°C

EC Directives Conformance

|

2004/108/CE (Electromagnetic Compatibility), 2002/96/EC, 2006/95/EC (Low Voltage)

INDESIT WASHING MACHINE

FAQS

What is the difference between a washing machine and a dishwasher?

A washing machine is used for washing clothes, while a dishwasher is used for washing dishes.

What is the difference between a washing machine and an iron?

A washing machine is used for washing clothes, while an iron is used to remove creases from clothes.

What is the difference between a washing machine and a tumble dryer?

A washing machine is used for washing clothes, while a tumble dryer is used for drying clothes.

How long should a Indesit washing machine last?

Washing manufacturer Indesit say that they expect their products to last 7-8 years. As Indesit also owns the Hotpoint brand, it is fair to say that this standard likely applies to these machines too.

What is the quickest wash on a Indesit washing machine?

As well as the three full-load programs, the new MyTime washing machine offers five further FastCycles:  Cotton 30°, Synthetics, Silk & Delicates, Wool, 15-minute Express. So there’s always an ideal solution for quickly cleaning a wide range of garments, even wool and delicates.

How long should a 40 wash take?

A 40°C wash usually takes  between 1 hour and 30 minutes and 2 hours and 30 minutes , depending on the size of the load. This wash is considered a warm wash and uses a low spin speed but higher temperatures than a cold wash.

Why does my washing machine take 2 hours?

A washer that continuously takes too long to wash  may have a malfunctioning load sense system, or greater problems with its control panel. There may also be issues with your water inlet valve, which pulls water into the appliance for each cycle.

Is quick wash good enough?

A quick wash naturally won’t clean as thoroughly as a full cycle. However, it would still be a good alternative if you just want to refresh your clothes or don’t deal with heavy stains.

Can you wash bedding at 60 if it says 40?

It is recommended that you wash your bedsheets in a hot wash, at least 60 degrees. The hotter that you wash your sheets, the more germs are removed meaning that your bedding will be properly clean and free of germs.

Why do eco washes take so long?

This is because  the bulk of energy used by the machine comes from heating the water  – the electricity needed to turn the drum or power the sprayers is comparatively much less. If the wash cycle is longer, the water doesn’t need to be heated up as much as shorter programmes.

What is the cheapest time to use a washing machine?

So, an alternative is to avoid peak laundry times:  4pm to 7pm. You could potentially save a few pennies per laundry load if you wash them in the morning, during the day (if you work from home), or later than 7pm in the evening.

Is 30 degrees a cold wash?

Is 30 degrees a cold wash?  No, a 30ºC wash is generally considered a warm wash. A cold wash is below 20°C and is usually reserved for clothes that are very delicate.

Does a 30 degree wash clean clothes?

In tests,  30-degree programs cleaned better than 20-degree programs , but they still didn’t wash out some stains such as olive-oil-based stains as well as a 40-degree wash. Greasy stains lifted even better if put on a 60-degree cycle.

How long is eco time on Indesit washing machine?

Calculates exactly the right amount of water to use whatever the size of the load. The Synthetics 40 programme effectively removes stains from your synthetic items, using a low-temperature 40°cycle in just  59 minutes.

Is it cheaper to wash clothes after 7pm?

The most expensive time for you to wash or dry your clothes is between 4pm and 7pm , so try to avoid using your machines between these hours.

What better eco wash or quick wash?

The eco setting on mine heats to 40 then switches the heater off, a standard 40 cycle keeps the heater on to maintain the temperature using more electric. It also does less agitation, as said above.  Quick wash tends to be for smaller loads so it’s not the wash I would use for a large load.

What uses the most electricity?

The Top 5 Biggest Users of Electricity in Your Home
Air Conditioning & Heating. Your HVAC system uses the most energy of any single appliance or system at 46 percent of the average U.S. home’s energy consumption.
Water Heating.
Appliances.
Lighting.
Television and Media Equipment.

What temp should you wash bedding?

When washing bedding you want to wash at  60 degrees  on a long wash ie 2 hours plus to make sure that any sweat, dander, dust or other nasties are killed and then removed. Wash all bedding on a full cycle 60-degree wash. Colder temperatures may not kill all the bacteria or remove sweat as effectively

Do washing machines use electricity when not in use?

Phantom energy: Do appliances use electricity when plugged in but turned off? The short answer is yes!  A variety of different electronic devices and appliances, including televisions, toasters, lamps, and more, when plugged in, can consume electricity even when they’re turned off.

Which wash cycle uses least electricity?

This is the easiest way to reduce electricity use, regardless of kind of washing machine you have. Washing with a cold cycle can save you more than 80% of your energy consumption and cost. This is because most of the energy is used just to heat up the water in warm washes.

What should I do if my Indesit washing machine has been damaged during transportation?****

If your washing machine has been damaged during transportation, contact the retailer and do not proceed any further with

How do I level my Indesit washing machine?****

To level your washing machine, install it on a flat sturdy floor, without resting it up against walls, furniture cabinets or anything else. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet. The angle of inclination, measured in relation to the worktop, must not exceed 2°.

How do I connect the water inlet hose to my Indesit washing machine?****

To connect the water inlet hose, screw it onto a cold water tap using a ¾ gas threaded connection. Before performing the connection, allow the water to run freely until it is perfectly clear. Connect the inlet hose to the washing machine by screwing it onto the corresponding water inlet of the appliance, which is situated on the top righthand side of the rear part of the appliance.

Can I use second-hand hoses for my Indesit washing machine?****

No, you should never use second-hand hoses for your washing machine. Use only the ones supplied with the machine.

How do I connect the drain hose to my Indesit washing machine?****

Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor; alternatively, rest it on the side of a washbasin or bathtub, fastening the duct supplied to the tap. The free end of the hose should not be underwater.

Can I use hose extensions for my Indesit washing machine?****

We advise against the use of hose extensions; if it is absolutely necessary, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

How do I clean my Indesit washing machine?****

The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives. Remove the dispenser by raising it and pulling it out. Wash it under running water; this operation should be repeated frequently.

Can children use the Indesit washing machine?****

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Can I repair the internal mechanisms of my Indesit washing machine myself?****

No, if the appliance breaks down, do not under any circumstances access the internal mechanisms in an attempt to repair it yourself.

How do I care for the door and drum of my Indesit washing machine?****

Always leave the porthole door ajar in order to prevent unpleasant odours from forming.

www.indesit.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>