TELLUR TLL331111 WiFi Smart Solar Camera User Guide

TELLUR TLL331111 WiFi Smart Solar Camera

Product Description

• Solar Panels
  When the sun is strong, that can charge the device battery.

• Infrared Light
  When the ambient light is not enough, enable the infrared light to increase the brightness of the environment.

• Light Sensor
  Used to collect ambient brightness values, when the illumination is lower than 2Lux, enable the infrared light.

• Pickup Device
  Collect ambient sounds and implement voice intercom.

• PIR Detection
  When the human body moves in front of the device, it can generate a trigger signal to the mobile phone.

• Lens
  Capture image video.
  Red light flashes slowly: the system waits in the WiFi configuration.
  The blue light is slow: the system is in normal working condition.
  Red and blue flashing alternately: system WiFi connection failed

• Reset Key
  The device in the working status, then press and hold for 5 seconds to restore the factory settings.

• Micro SD slot
  Install Micro SD card to support local recording

• Battery Switch
  Turn off and turn on the device battery by turning on the key

• USB Interface
  Charge the device battery through the USB interface

• Bracket mounting
  Mounting on the wall using the accessory bracket

• Speaker
  Issue system prompts and implement voice intercom

Note: You need to detach the bottom silicone to see the function interface as shown.

Installation

Operate as shown, using mounting screwsInstall the bracket and adjust the angle to make the PIR Enough to detect people.

Installation Notes

Installation:

1. The human body induction effective distance is 3-5 meters, so please adjust the monitoring angle according to the actual situation.
2. Please avoid the installation position where the temperature changes too much, such as heat source, airoutlet, etc. it will cause false alarm of equipment.

Alarm Adjustment:
The device default setting triggers the alarm immediately. If you need to adjust the sensitivity, please go to the device settings page.

Solar Panels:
Please ensure that the sun is fully exposed.

Connect

Download the Tellur Smart App for both iOS and Android OS. Scan the QR code to download Tellur Smart App

Adding a New Device

• Turn on power of device being paired and make sure light is flashing quickly.
• Open App and Click “+” to add appropriatedevice.
• Select WiFi network and input password of WiFi then.
• Once connected the App will prompt the connection, then you can rename the device or just click “done”.

•  Once App is installed on your device and you have added your smart device to your app you will be able to control it.

QR Code Configuration Getting Started

1. Please follow the instructions and make sure the passwords are inputed correctly.
2. One device can only be added with one App account, if the device has been added with another account already, then it can’t be added to any another account again.
3. The device will be unbind from previous account after been deleted from App. Further ,the device will be resetted automattically once from blue light to red light

Process

Step 1: Open the Tellur Smart App, click “+” or “Add Device”.
Step 2: Select “Smart Camera”.
Power the device on and make sure the indicator is flashing quickly or a prompt tone is heard.

Step 3: Input WiFi passwords and click “Confirm”, scan the QR Code with a device. (You can change the network connection)

Technical Specification

• Sensor type: 1/4” CMOS
• Sensor resolution: 1.3 Megapixels
• Lens: F:1.4 f:2.8mm
• View angle 143°
• Inflared sensor: Yes, up to 10 meters
• Image resolution: HD 960P 1280*960
• Video compresion: H.264
• Bit rate: 32Kbps~2Mbps
• Frame rate: 1~25/second
• Internal storage: MicroSD card (up to 32GB)
• Night vision: Yes
• Motion detection: Yes
• Audio comunication: Two-way audio
• Waterproof: IP65
• WiFi standard: IEEE 802.11b/g/n
• Supported WiFi network: 2.4GHz
• Battery: 3.7V, 6400mAh Li-ion Rechargable
• Dimensions: 2107589MM
• Weight: 480g

Declaration of Conformity

We, ABN SYSTEMS INTERNATIONAL S.R.L., Bucharest, Sector 1, Marinarilor street, nr. 31, we declare on own responsibility that the product below:
Product description: WiFi Smart Outdoor Solar Camera Brand: Tellur
Product code: TLL331111
It does not endanger life, health, work safety, does not have a negative impact on the environment and corresponds to the standards stated in the manufacturer’s declaration of conformity. The product is in compliance with the following standards and / or other normative documents:

RED – 2014/53/EU
Applied standards:
EMC: ETSI EN 301 489-1 V2.2.0
ETSI EN 301 489-17 V3.2.0
Radio: ETSI EN 300 328 V2.1.1 (2016-11)
ETSI EN 300 220-1 v2.4.1
ETSI EN 300 220-2 v2.4.1
Health: EN 62479:2010
Safety: EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
RoHS – 2011/65/EU

The product bears CE mark, applied in 2019
Name: George Barbu
Function: Director General
Place and date: Bucuresti, 20-06-2019

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>