Contours C005-R1 3 in1 Baby Carrier Instruction Manual

June 17, 2024
Contours

Contours logo

C005-R1 3 in1 Baby Carrier

Contours C005-R1 3 in1 Baby Carriercontoursbaby.com
Consumer Service: 1.888.226.4469
www.contoursbaby.com
https://manual-hub.com/

WARNING

Your child’s safety depends on you. Proper product use cannot be assured unless you follow these instructions. Read all instructions BEFORE assembly and use of the soft carrier. Keep instructions for future use.

IMPORTANT SAFETY INFORMATION:

How to Keep Your Child Safe While Using this Baby Carrier

  • PRODUCT WEAR WARNING: This product is subject to normal wear and tear over time. The user should inspect this product for signs of deterioration such as ripped or loose seams, torn straps or fabric, damaged fasteners, and hardware not locking before each use. DO NOT USE THIS CARRIER IF PROBLEMS ARE DETECTED. CALL 1-888-226-4469, or if outside the U.S.A. and Canada, call 1-312-361-6493.
  • Premature infants, infants with respiratory problems, and infants under 4 months are at greatest risk of suffocation.

FALL AND SUFFOCATION HAZARD
FALL HAZARD – Infants can fall through a wide leg opening or out of carrier.

  • Adjust leg openings to fit baby’s legs snugly.
  • Before each use, make sure all buckles, straps, and adjustments are secure.
  • Take special care when leaning or walking.
  • Never bend at waist; bend at knees.
  • Only use this carrier for children between 8 lbs. and 30 lbs.

SUFFOCATION HAZARD – Infants under 4 months can suffocate in this product if face is pressed tight against your body.

  • Do not strap infant too tight against your body.
  • Allow room for head movement.
  • Keep infant’s face free from obstructions at all times.
  • Ensure proper placement of child in product including leg placement.
  • The infant must face towards user until infant can hold its head upright unassisted.
  • Do not allow child to face forward until they can be properly positioned with legs straddling the seat.
  • ALWAYS adjust the seated position per the instructions. FOR INFANTS 8 lbs. to 5 months, the seated position gussets must be closed in the Seated Position with the side buckles buckled to the carrier body.
  • Always make sure that your infant’s nose and mouth are clear and unobstructed by the carrier or clothing. Always keep some distance between the infant’s face and the adult’s body to ensure easy breathing.
  • DO NOT put items into the carrier with the child. This may interfere with the child’s ability to breathe.

WARNING

  • This baby carrier is designed for use by adults while walking only. Never use a soft carrier when balance or mobility is impaired because of exercise, drowsiness, or medical conditions. Please be aware that while using carrier, normal activities or motions may now be dangerous to your child and caution should be used. DO NOT cook, clean, run, ski, bike, ride horses or use any type of motorized vehicles, etc. while using this carrier.

  • Never use a soft carrier while engaging in activities such as cooking and cleaning which involve a heat source or exposure to chemicals.

  • DO NOT use this carrier unless infant meets the following weight requirements:
    MINIMUM WEIGHT: 8 lbs. (3.5 kg)
    MAXIMUM WEIGHT: 30 lbs. (13.6 kg)

  • Hold on to your infant tightly until all buckles and latches are secured in place and straps are pulled tight around the user’s body.

  • NEVER Leave Child Unattended. NEVER leave child in the baby carrier unattached to user.

  • MAKE SURE child’s body parts and skin are clear when locking buckles or snaps to prevent pinching.

  • DO NOT place sharp objects into carrier pockets.

  • Let carrier cool after leaving in sun or hot car.

  • User Should Not Use This Baby Carrier:
    – If experiencing back problems
    – If carrier obstructs the wearer’s vision
    – As a backpack or hip carrier
    – As a car safety seat
    – Lying down
    – While driving or being a passenger in a motor vehicle.

PARTS LIST

FRONT VIEW Contours C005-R1 3 in1 Baby Carrier - PARTS
LISTBACK VIEW Contours C005-R1 3 in1 Baby
Carrier - PARTS LIST 1Newborn 0-5 months: Seated Position Facing You. Minimum 8 lbs. / 3.5 kgs.

  1. Wrap the Waist Strap around your waist and feed the Waist Strap Buckle through the Waist Strap Loop.
    To adjust how high or low you are carrying your baby, position the waist strap up higher around your waist or lower on your hips. You should be able to easily kiss the top of your baby’s head.Contours C005-R1 3 in1 Baby Carrier - assembly 1

  2. Buckle the Waist Strap Buckle, and tighten the Strap until it is comfortably snug.Contours C005-R1 3 in1 Baby Carrier - assembly 2

  3. If your Waist Strap has extra length, roll the extra webbing to the desired length and use the elastic loops to hold the rolled-up webbing.Contours C005-R1 3 in1 Baby Carrier - assembly 3

  4. Make sure the Seated Position Gussets are closed in the Seated Position. To close the black mesh gussets, lift the tab of the buckle up and pull on the strap until the mesh is completely cinched.Contours C005-R1 3 in1 Baby Carrier - assembly 4

  5. Lift and hold your baby up to your chest facing you, making sure to support their head and neck, and use one hand to lift the Back Strap over your head until it is behind your neck.Contours C005-R1 3 in1 Baby Carrier - assembly 5

  6. Reach around the front of the carrier to buckle the Side Buckle. Be sure to hold your child close to you. Repeat for the other Side Buckle. Tighten both Side Straps until they are comfortably snug for you and your baby. If your waist or shoulder Side Straps have extra length, you can roll the extra webbing to the desired length and use the elastic loops to hold the rolled-up webbing.
    a. For newborns, your baby should be in a fetal position with their feet together, knees spread slightly, and knees level with their belly button.
    CAUTION: Do not pull your baby’s legs to a straight position. Your baby will start to naturally straighten their legs over the first 10+ weeks. As your baby grows, their hip joints should naturally and gradually loosen, allowing their feet to spread into a seated position where the knees drop lower to be level with their hips. Contours C005-R1 3 in1 Baby Carrier - assembly
6b. For babies whose legs and hips naturally fall or spread apart to the side, their thighs should be supported by the fabric of the carrier.Contours C005-R1 3 in1 Baby Carrier - assembly
7

  7. Until your child has head and neck control (generally around 4 months), make sure the Head Support Buckles are buckled to the Shoulder Straps, with the Head Support in the Up position. The top of your child’s ears should be below the top of the Head Support. For extra support and comfort, you can adjust the tightness of the Head Support with the Head Support Zippers. (see pg. 15)  Contours C005-R1 3 in1 Baby Carrier - assembly 8

  8. Check your baby often and make sure they are centered in the carrier, their thighs are in a supported position, and their head is upright (and not resting on their chest). Proper head placement, with at least two fingerswidth clearance under your baby’s chin, will avoid airway constriction and allow your baby to breathe properly.Contours C005-R1 3 in1 Baby Carrier - assembly 9

  9. Make sure you can easily kiss the top of your baby’shead.
    To adjust how high or low you are carrying your baby, position the waist strap up higher around your waist or lower on your hips. You should be able to easily kiss the top of your baby’s head.Contours C005-R1 3 in1 Baby Carrier - assembly 10 NOTE: See pg. 16 for instructions on taking off the carrier.

From 6+ months: Seated Position Facing You. Maximum 30 lbs. / 13.6 kgs.

  1. Wrap the Waist Strap around your waist and feed the Waist Strap Buckle through the Waist Strap Loop.
    To adjust how high or low you are carrying your baby, position the waist strap up higher around your waist or lower on your hips. You should be able to easily kiss the top of your baby’s  head.Contours C005-R1 3 in1 Baby Carrier - assembly 11

  2. Buckle the Waist Strap Buckle, and tighten the Strap until it is comfortably snug.Contours C005-R1 3 in1 Baby Carrier - assembly 12

  3. If your Waist Strap has extra length, roll the extra webbing to the desired length and use the elastic loops to hold the rolled-up webbing. Contours C005-R1 3 in1 Baby Carrier - assembly 13

  4. Make sure the Seated Position Gussets are closed in the Seated Position. To close the black mesh gussets, lift the tab of the buckle up and pull on the strap until the mesh is completely cinched.Contours C005-R1 3 in1 Baby Carrier - assembly 14

  5. Lift and hold your baby up to your chest facing you, making sure to support their head and neck, and use one hand to lift the Back Strap over your head until it is behind your neck.Contours C005-R1 3 in1 Baby Carrier - assembly 15

  6. Reach around the front of the carrier to buckle the Side Buckle. Be sure to hold your child close to you. Repeat for the other Side Buckle. Tighten both Side Straps until they are comfortably snug for you and your baby. If your waist or shoulder Side Straps  ave extra length, you can roll the extra webbing to the desired length and use the elastic loops to hold the rolled-up webbing.Contours C005-R1 3 in1 Baby Carrier - assembly 16

  7. Depending on your preference, you can buckle the Head Support in either the up or down position. For extra support and comfort in the up position, you can adjust the tightness of the Head Support with the Head Support Zippers. (See pg. 15)
    WARNING: Do not unbuckle the Head Support Buckles, or buckle the Head Support in the down position, if your child does not have head and neck control. Your child must face towards you until he or she can hold their head upright.Contours C005-R1 3 in1 Baby Carrier - assembly
17

  8. Check your baby often and make sure they are centered in the carrier and that their head is upright (and not resting on their chest). Proper head placement, with at least two fingers-width clearance under your baby’s chin, will avoid airway constriction and allow your baby to breathe properly.Contours C005-R1 3 in1 Baby Carrier - assembly 18

  9. Make sure you can easily kiss the top of your baby’shead.
    To adjust how high or low you are carrying your baby, position the waist strap up higher around your waist or lower on your hips. You should be able to easily kiss the top of your baby’s head.

NOTE: See pg. 16 for instructions on taking off the carrier.
From 6+ months: Explore Position, Facing Outwards. Maximum 30 lbs. / 13.6 kgs.

  1. Wrap the Waist Strap around your waist and feed the Waist Strap Buckle through the Waist Strap Loop.
    To adjust how high or low you are carrying your baby, position the waist strap up higher around your waist or lower on your hips. You should be able to easily kiss the top of your baby’s head.Contours C005-R1 3 in1 Baby Carrier - assembly 19
  2. Buckle the Waist Strap Buckle, and tighten the Strap until it is comfortably snug.Contours C005-R1 3 in1 Baby Carrier - assembly 20
  3. If your Waist Strap has extra length, roll the extra webbing to the desired length and use the elastic loops to hold the rolled-up webbing.Contours C005-R1 3 in1 Baby Carrier - assembly 21
  4. Open the black mesh gussets by lifting the tab of the buckle up and pulling the bottom edge of the gusset until the mesh is completely open and the strap is hidden.
  5. Buckle the Head Support Buckles in the Down position.Contours C005-R1 3 in1 Baby Carrier - assembly 23
  6. Lift and hold your baby up to your chest facing away from you, and use one hand to lift the Back Strap over your head until it is behind your neck.Conactours C005-R1 3 in1 Baby Carrier - assembly 24
  7. Reach around the front of the carrier to buckle the Side Buckle. Be sure to hold your child close to you. Repeat for the other Side Buckle. Tighten both Side Straps until they are comfortably snug for you and your baby. If your Side Straps have extra length, roll the extra webbing to the desired length and use the elastic loops to hold the rolled-up webbing.Contours C005-R1 3 in1 Baby Carrier - assembly 25
  8. Check your child often and make sure they are centered in the carrier. Enjoy the great big world together.Contours C005-R1 3 in1 Baby Carrier - assembly 26

Adjusting the Head Support –

  1. Until your child has head and neck control (generally around 4 months), make sure the Head Support Buckles are buckled to the Shoulder Straps, with the Head Support in the Up position.
  2. For extra comfort, you can zip the Head Support Zippers up or down, depending upon the age and size of your child.
  3. When your child is facing forward, the Head Support should always be buckled in the Down position.

How to Take the Carrier Off

  1. While holding your child to your chest, unbuckle the Side Buckles by pressing the Buckle Lock and squeezing both Tabs.
    Contours C005-R1 3 in1 Baby Carrier - assembly 30

  2. While supporting your child, lift the Shoulder Straps over your head until the Back Strap is in front of you.

  3. Take your child out of the carrier.Contours C005-R1 3 in1 Baby Carrier - assembly 31

  4. Unbuckle the Waist Strap.

CARE & MAINTENANCE

  • Make sure all buckles are fastened before washing. Place in a laundry bag and machine wash in cold water with mild detergent on the gentle cycle. Line dry. Do not iron, use bleach or machine wash frequently.
  • Periodically check for worn parts, torn materials or stitching.
  • Call Consumer Services (888-226-4469) immediately if you notice any damaged parts.

LIMITED WARRANTY

Contours® warrants this product to be free of defects in materials and workmanship, as follows: For a period of ONE YEAR from the date of purchase, Contours will repair or replace, at its option, the defective product. If you have a problem or are not satisfied with this product, please contact the Consumer Service Department at Contours.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. CONTOURS SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, EXCEPT TO THE EXTENT REQUIRED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE DURATION OF THIS WARRANTY.
Some states do not allow the exclusion or limitation of warranties set forth above, so the above exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. We sincerely thank you for your purchase of this Contours product.
To obtain warranty service, please call Contours Consumer Service Department at 1-888-226-4469 in U.S. and Canada, 1-312-361-6493 outside U.S. and Canada or contact us via email at customerservice@contoursbaby.com If the product is returned to Contours Consumer Service Department for repair or replacement, it must be shipped prepaid and adequately insured.
For further information visit www.contoursbaby.com
Recall WEBSITE: HELP KEEP YOUR CHILD SAFE. Check www.recall.gov to see if any products you use with your child or any of your child’s toys have been recalled.

PERSONAL RECORD CARD

Once in a while, we are less than perfect and one of our products with a problem reaches a customer. In most cases, we can solve your problem with replacement parts. Please contact us before you return one of our products to the store.
If you have a question about your product, please have the following available when you call:

  • Product model number
  • Date of manufacturing

You can find the Model Number and Date of Manufacture on a label located on a strap of the baby carrier.
Having this information ready will expedite your service call.
Please direct any comments, questions or replacement part requests to:

Contours® Consumer Service Department
1100 W Monroe St
Chicago, IL 60607
1-888-226-4469 in U.S. & Canada, 1-312-361-6493 outside U.S. & Canada
Central Standard Time, 8 am-5 pm Monday – Thursday, 8 am – 3 pm Friday
e-mail:customerservice@contoursbaby.com
Model / Style Number: _____
Date of Manufacture: __
Date of Purchase: ____
Consumer Service: 1.888.226.4469
www.contoursbaby.com

Documents / Resources

| Contours C005-R1 3 in1 Baby Carrier [pdf] Instruction Manual
C005-R1 3 in1 Baby Carrier, C005-R1, 3 in1 Baby Carrier, Baby Carrier, Carrier
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals