Sprite Group E10 True Wireless Earbuds User Manual

Sprite Group E10 True Wireless Earbuds User Manual

SAFETY CAUTION

• Do not use earphones & speaker while driving, please observe the national and regional regulations.
• Ensure all equipment and accessories are safely stored from children or pets.
• Do not use the product in extreme temperatures either below 14 degrees Fahrenheit or above 113 degrees Fahrenheit this may cause deformations, reduce the charging capacity of the device, and shorten the service life of the product.
• Do not use wet equipment, liquid can cause severe damage to the equipment.
• Please do not use wet hands while operating the equipment, as it may cause damage and is not covered under the scope of the warranty.
• If the earphones & speaker play at a high volume for a long period of time, your hearing may become impaired and we suggest using the lowest volume of the phone.

TRUE WIRELESS EARBUDS OPERATION INSTRUCTIONS

Initial Earbuds Set Up/Pairing
Step 1 : Once both earbuds are removed from the case they will automatically power on and enter pairing mode.
Step 2 : Go to the Bluetooth connection list on your smart phone/tablet/laptop search for Bluetooth name on your device. Click to connect.

TRUE WIRELESS EARBUDS OPERATION INSTRUCTIONS

Power On: Once both earbuds are removed from the case they will automatically power on. Or long touch earbuds about 3 seconds to manually power on.

• Power Off: Once both earbuds are put in the case they will automatically power off.
• Music Play/Pause: Short press button to play or pause music.
• Music Next/Previous: Double press the main button of © earbuds to go to the previous song. Double press the main button of ®earbuds to go to the next song.
• Answer Call: During incoming call, press the main button of earbuds to answer a call.
• End Call: During a call, press the main button of earbuds to end a call.
• Reject Call: During an incoming call, press the main button of earbuds 1 second to reject a call.
• Cancel Call: During the dialing state, press the main button of earbuds to cancel a call.
• Siri/Google Assistant: Under stand by status or music pause status, press for 1.5 seconds on the main button of or earbuds to activate voice assistance.
• Low Battery Alarm: When the earbuds power is less than 20%, the red light will flash every 5 second and one prompt will be sounded every 60 seconds to charge.
• Low Battery Shutdown: When the earbuds run out of battery power, they will automatically shut off.
• Automatic Connection: After the initial set-up and connection the earbuds will automatically connect to your device the next time you turn them on. (Please ensure the Bluetooth is active on your device for automatic connection.)
• Restore Original Settings : If two earbuds are not in connection state, power on earbuds and with red and blue light, dick both button for 5 times continuously, earphones enter restore setting and will turn off after finish. If 2 earbuds are in connection, click the flashing light earphone button for 5 times continuously, can make restore original setting for both earbuds.

Charging for Earbuds

Put and earbuds into the Charging Cases and close the lid to start the charging process. The charging earbuds will be red lights until fully charged. Once fully charged the red light will turn off. At the same time the charging case will be blue light when the earbuds is charging, and will be off once earbuds charging full.

Charging for charging case

When the type-C interface is used to charge the charging chamber, the red light will flash, and the red light will be constant on when it is full.
(Note: The normal Charging Case holds 320 mAh of battery power which can charge the earbuds up to 4 times from no battery power before the case has to be charged.)

                    True Wireless     Earbuds Specifications

Bluetooth Version| V5.1
Bluetooth Distance| 10M
Battery Voltage| 3.7V
Earbuds Battery Capacity| 30mAh
Charing Case Battery Capacity| 320mAh
Charging Time| About 1 hour
Playing Time| About 5 hours
Charging Interface| Type-C
Water Resistance| IPX8

Address: 4th Floor,A3 Building, Shelliang Industry Zone, NO.299  Guanping Road, Longhua District, Shenzhen, China.

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Pad 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Conned the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>