CRUX SWRHK-65E Radio Replacement with Steering Wheel Instruction Manual

: June 17, 2024
: CRUX

Table of Contents

CRUX SWRHK-65E Radio Replacement with Steering Wheel
Specifications
Product Usage Instructions
FAQ
PRODUCT FEATURES
PARTS INCLUDED
INSTALLATION DIAGRAM
DIP SWITCH SETTINGS
VEHICLE APPLICATIONS
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CRUX SWRHK-65E Radio Replacement with Steering Wheel

Specifications

Product Name: SWRHK-65E
Compatibility: Hyundai and Kia vehicles with 24 & 18 Pin Connectors
Features:
- Retains factory features in select Hyundai and Kia vehicles
  while functioning with an aftermarket radio.
- Retains factory 3.5mm Aux Input Jack (if equipped).
- Pre-programmed to retain factory Steering Wheel Controls.
- EIA colour-coded wiring for easy installation.

Product Usage Instructions

MM SWC Cable Connection

Plug in the 3.5MM SWC cable to the 4-pin port on the module. See the DIP SWITCH SETTINGS section for the correct settings based on the aftermarket radio you are using.

Note: Insulate the Blue/Yellow wire or 3.5mm plug if not being used.

For aftermarket radios that have wires for SWC connections cut off the 3.5mm plug on the Crux SWC Cable and connect the SWC wires as follows:

RED to SWC Key 1
WHITE to SWC Key 2
SHIELD to SWC Ground

Vehicle Applications

Elantra
Genesis Coupe* (without NAV)
Santa Fe* (without NAV)
Santa Fe Sport* (without NAV)
Sonata* (without NAV)
Sonata Hybrid* (without NAV)
Tucson
Veloster

Not compatible with amplified systems.

FAQ

Q: What is the compatibility of SWRHK-65E?
A: SWRHK-65E is compatible with Hyundai and Kia vehicles with 24 & 18 18-pin connectors.
Q: What factory features does SWRHK-65E retain?
A: SWRHK-65E retains factory features in select Hyundai and Kia vehicles while functioning with an aftermarket radio. It also retains the factory 3.5mm Aux Input Jack (if equipped) and is pre-programmed to retain factory Steering Wheel Controls.
Q: How is the SWC cable connected?
A: The 3.5MM SWC cable should be plugged into the 4-pin port on the module. Refer to the DIP SWITCH SETTINGS section for the correct settings based on the aftermarket radio being used. If the aftermarket radio has wires for SWC connections, cut off the 3.5mm plug on the Crux SWC Cable and connect the SWC wires as described in the instructions.

PRODUCT FEATURES

Retains factory features in select Hyundai and Kia vehicles while functioning with an aftermarket radio.
Retains factory 3.5mm Aux Input Jack (if equipped).
Pre-programmed to retain factory Steering Wheel Controls.
EIA colour-coded wiring for easy installation.

PARTS INCLUDED

INSTALLATION DIAGRAM

Note
The output signal(s) stated above may not cover all Year/Model.

DIP SWITCH SETTINGS

AFTERMARKET RADIO DIP SWITCH SETTINGS

RADIO BRAND: DIP: 1 2 3 4

Atoto, Dual, Farenheit, Jensen, Pioneer	OFF	OFF	ON	ON
Power Acoustik, Soundstream	OFF	OFF	ON	ON
Blaupunkt, Most off-brand Radios	OFF	OFF	ON	ON
Alpine	OFF	OFF	OFF	OFF
Clarion	OFF	ON	ON	OFF
Kenwood	OFF	ON	ON	ON
JVC	OFF	ON	OFF	ON
Boss, Old Sony	OFF	ON	OFF	OFF
New Sony	OFF	OFF	ON	OFF

NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most off-brand radios, check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.

HYUNDAI / KIA STEERING WHEEL CONTROL DIP SWITCH SETTING

3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable and set the DIP switches to the aftermarket radio you are using. Use the Blue/Yellow wire for Kenwood and JVC radios and the 3.5mm plug for other radios.
NOTE: Insulate the Blue/Yellow wire or 3.5mm plug if not being used.