DEMA 910N 10 Gallon Air Operated Portable Foam Equipment User Manual

June 17, 2024
DEMA

USER MANUAL

MODEL NUMBER:
910N/910NK/910NV
AND RELATED UNITS
10 Gallon Air Operated Portable Foam Equipment
(Original Instructions )

910N 10 Gallon Air Operated Portable Foam Equipment

READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT

WARNING

DEMA 910N 10 Gallon Air Operated Portable Foam Equipment - Symvbol
1

Read this manual completely and understand the machine before operating or servicing it.

  • Always wear protective clothing, gloves, and eyewear while operating or servicing unit.
  • Avoid contact of cleaning agent with skin and eyes. If contact occurs, see MSDS sheet for further first aid measures.
  • Follow safety instructions of chemical manufacturer (MSDS).
  • Never point the discharge wand at anyone.
  •  Incoming air pressure cannot exceed 100 psi (7 bar).
  • After each use, relieve all remaining pressure in the system by unplugging the air line from the unit and opening the discharge ball valve to prevent accidental discharge.
  • After relieving the pressure from the unit, store the unit with the ball valve in the closed position.
  • Be sure to flush the unit with fresh water for 5 minutes when switching from an alkaline to an acid or an acid to an alkaline.
  • Do not exceed a fluid temperature of 100˚F (37˚C).
  • Only use clean and dry air. Air must be filtered and free of moisture or pump life will be diminished. If needed, install an air dryer before unit.
  • Do not use air lubricator before the unit.

PROTECT THE ENVIRONMENT
Please dispose of packaging materials, old machine components, and hazardous fluids in an environmentally safe way according to local waste disposal regulations.
*** Always remember to recycle.
Specifications and parts are subject to change without notice.

Specifications:

Hose ………. 20 feet reinforced hose, 1/2 inch inside diameter (6 meters reinforced hose, 12.7 mm inside diameter)
Foam Output……………………………. 15 to 30 gallons/minute (57 to 144 liters/minute)
Foam Distances ……………………….. 15 to 20 feet (4.6 to 6 meters)
Liquid Temperature ………………….. 40˚F to 100˚F (4.4˚C to 37˚C)
Noise Level………………………………. Average 79 dB(A)
Discharge Wand Vibration Level ….. Maximum 2.5 m/s²

Dimensions:
Length ………………………………… 19 in (483 mm) approximately
Width …………………………………. 16 in (406 mm) approximately
Height ………………………………… 41 in (1041 mm) approximately
Weight, including discharge hose and wand:
(Empty) ………………………….. 39 lbs (18 kg) approximately
(Full) ……………………………….. 138 lbs (63 kg) approximately

Requirements:
Compressed Air Pressure Requirements: Air regulator (R25)
factory set at 50 psi (3.4 bar). Operating range is 40 to 80 psi (3 to 5 bar) with 5 to 8 CFM (141.64 to 226.62 l/min)
Chemical requirements: follow all instructions from chemical manufacturer.
Air Operated Double Diaphragm Pump Models Offered:
P56: Polypropylene body with Santoprene diaphragm
P56V: Polypropylene body with Viton diaphragm
P56K: Polypropylene body with Kalrez diaphragm
Acceptable Products:
Alkaline cleaners, Caustic cleaners, Sanitizers, and Acids

  • D-Limonene may only be used with Kalrez pump
  • Chlorine may only be used with Viton or Kalrez pump
    DO NOT USE: All hydrocarbons

Operation Instructions:

  1. Follow all instructions from chemical manufacturer.
    Fill the tank with water and the advised percentage of chemical concentrate.

  2. With ball valve (HV60) in the closed position, plug an air line into the air fitting (AP25).

  3. Slowly open the ball valve (HV60) completely.

  4. Adjust the needle valve (NV14Y) to desired wetness or dryness of foam following the steps below:
    a. Close needle valve completely in clockwise direction.
    b. Open needle valve in counter-clockwise direction 3 complete turns.
    c. Continue to open valve in ¼ turn increments allowing 30 seconds between adjustments until proper consistency of foam is achieved.

After Use Instructions:

  1. Flush the unit with fresh water for 5 minutes.
  2. Disconnect the air line from the air fitting (AP25) and relieve any remaining pressure in the system by opening the discharge ball valve (HV60).
  3. Close the ball valve (HV60) after all pressure has been relieved from the system.

Maintenance Instructions:

To keep your portable tank foamer operating properly, periodically perform the following maintenance procedures:

  • Check the air pump (P56/P56K/P56V) for wear and leaks.
  • Inspect hoses for leaks or excessive wear. Make sure all hose clamps are in good condition and properly secured.
  • Replace filter (AFR25) in regulator (R25) as needed.
  • Check the suction tube and screen for debris and clean as needed.
  • Drain compressor tank on a regular basis to ensure proper operation of pump.

Troubleshooting Instructions:

  • Check to ensure the discharge hose is uncoiled properly, and that there are no kinks that could obstruct fluid flow.

  • Check air regulator bowl (ABR25) for debris such as water, oil, or rust particles. Clean by unthreading the air regulator bowl from the air regulator (R25).

  • If needle valve (NV14Y) valve is open too far, the pump (P56/P56K/P56V) will cycle improperly due to lack of air pressure. If this occurs, reset needle valve as described in Operation Instruction #4.

  • Make sure proper foaming chemical and concentration is being used.

  • If air passes through the pump (P56/P56K/P56V) without cycling, the pump needs to be replaced.

  • If foam solution backs up into air regulator bowl (ABR25), the check valve (CV38) needs to be replaced.

  • If foam comes out wet, no matter where the needle valve (NV14Y) is positioned, the check valve (CV38) may need to be replaced.

  • Check for proper air pressure on air gauge (AG100). Air regulator (R25) is factory set at 50 psi (3.4 bar). Operating range is 40 to 80 psi (3 to 5 bar) with 5 to 10 CFM (141.64 to 283.30 l/min)

  • If the unit foams at a reduced pressure:
    o Check the air compressor supplying the unit. If the pressure is less than 40 psi, turn the foam unit off until the compressor can catch up.
    o If the air supply is 50 psi (4.14 bar) or above, check the AG100, which should read near 50 psi (4.14 bar).
    If the AG100 is more or less than 50 psi (4.14 bar), adjust the pressure by turning the knob on the top of the air regulator (R25).
    o If both of the above are okay, the stainless steel mixing mesh (SS-MESH) could be plugged. Remove and clean it by following the instructions below:
    1. Be sure the foam unit is not plugged into an air supply and be sure to relieve all stored pressure in the unit by having the ball valve (HV60) in the open position.
    2. Remove the stainless adaptor (SSA12) from the tee fitting (SST12HB38).
    3. Remove the screen and the mixing mesh from inside the tee fitting (SST12HB38).
    4. Clean any particles from the mixing mesh and the screen.
    5. Replace the mixing mesh and then the screen into the back of the tee and screw the stainless adaptor back into the tee. It is recommended to use a pipe thread sealant when reinstalling the stainless adaptor back into the tee fitting (SST12HB38). If the mixing mesh has a lot of foreign particles in it, make sure the strainer (STR38-IL) is still in place.

  • Check for plugged strainer (STR38-IL). Replace strainer if necessary. Strainer must be used.

TANK ASSEMBLY

ITEM NUMBER: TANK-10N-A

DEMA 910N 10 Gallon Air Operated Portable Foam Equipment - Fig
1

DEMA 910N 10 Gallon Air Operated Portable Foam Equipment - Fig
2

DEMA 910N 10 Gallon Air Operated Portable Foam Equipment - Fig
3

ITEM NUMBER DESCRIPTION
AG100 1.5 INCH DRY MODEL 20 DUAL SCALE GAUGE
AP25 PLUG 1/4 NPTM AIR FITTING – BRASS
AS 1-VS 1/4-20 X 1/2 PHIL TRUSS MACH SCREW 19-8 W/516 ORANGE V1BRASEAL PATCH
B8X58 8.15 X 5/8 inch PHIL FLAT TI-A 316 S.S.
BPS-5850 Back Panel Screw – 5/8 inch with Stand Off
BPS-SSR 1/4 INCH PUSHNUT BOLT RETAINER STAINLESS STEEL
COT 1/8 X 1 COTTER PIN 18-8 S/S
CV38 PVC CHECK VALVE 3/8 BARBS • SS SPRING
DFP7 7 INCH HINDGED CAP INCLUDES LID FLANGE AND HINGE PIN
OFP7-C 7 INCH DRAIN CAP POLYPRO BLACK
OFP7-F 7 INCH TANK LID FLANGE POLYPRO
DFP7-PIN HINGE PIN FOR DFP7-C& DFP7-C
DFP7-C-BL 7 INCH FILL CAP POLYPRO BLUE PANTONE
DFP7-C-GN 7 INCH FILL CAP POLYPRO GREEN PANTONE
DFP7-C-RD 7 INCH FILL CAP POLYPRO RED PANTONE
DFP7-C-YL 7 INCH FILL CAP POLYPRO YELLOW PANTONE
DP-A 7 INCH HINDGED CAP INCLUDES LID FLANGE AND HINGE PIN
OP FRONT DRAIN PLUG FOR PORTABLE UNIT POLYPRO
OP-G F KM SQUARE CUT DRAIN PLUG GASKET
DP-INSERT 304 STAINLESS DRAIN PLUG INSERT
ECl2 OETIK ER CLAMP 21.0-706R
K14-2 OETIKER CLAMP 13.8
F12SS STAINLESS .875 ID FERRULE FOR 1/2 INCH HOSE
F38SS STAINLESS 3/8 INCH FERRULE
FACI14 FEMALE COUPLER – 1/4in NPTF
FWAX15 FLAT AXLE WASHER
FWP12 7/81D X 1.5 OD X 0.05 THK SSFW
FWP14 C-816 1/2in SS WASHER
H12B-H 1/2 INCH BLUE GOODYEAR HORIZON HOSE -Available per ft.
H14B-H 1/4 INCH BWE HOSE- GOODYEAR HORIZON – Available per ft.
H38B-H 3/8 INCH BWE GOODYEAR HORIZON HOSE – Available per ft.
HBBF1438 BRASS 1/4in F PT X 3/8in HOSE BARB
HBSSI212 STAINLESS HOSE BARB 1/2 X 1/2
HBSS1438 STAINLESS HOSE BARB 1/4 MPT X 3/8 BARB
HBSSEL1238 304 S.S. 1/21n MPT BY 3/8In H.B. ELBOW
HBSSEL1438 STAINLESS HOSE BARB ELBOW 1/4 INCH NPT X 3/8 HOSE BARB
HBSSEL1814 304 STAINLESS ELBOW 1/8 INCH NPT X 1/4 INCH HOSE BARB
HHPB3412 HEX HEAD POLY REDUCER BUSHING 3/4 X 1/2
HHSB1214 HEX HEAD S.S. REDUCER BUSHING 1/2 X 1/4
FN60 1/21n STAINLESS BALL VALVE – w/ WELDED NUT
NV14Y FLOW CONTROL VALVE – INCLUDES BLACK KNOB
NV14Y•tiNDL KNOB FOR 2839.1/4 NEEDLE VALVE
P56 5700 PUMP WITH SANTOPRENE SEALS – INCLUDES HOSE BARBS
P56K 5700 PUMP WITH KALREZ SEALS – INCLUDES HOSE BARBS
P56V 5700 PUMP WITH VITON SEALS – INCLUDES HOSE BARBS
207561038 Polypro 657 Air Port x HB Straight, w/ Viton o-ring
H814P 1/4in BRASS FIB AIR FITTING /G57/P56
1485638 HOSE BARB FOR P56 PUMP
H8563814 HOSE BARB FOR P56K PUMP
148563W HOSE BARB FOR P56V PUMP
P56•13RICT PUMP BRACKET- STAINLESS STEEL
P56-BRKT-SCREW HI LO SCREW FOR RETAINING P56-BRKT
PLPF PORTABLE FOAM ER BACK PLATE W/ HINGE AND HOLES
PLPF-PIN 302 STAINLESS PORTABLE PLATE HINGE PIN
PVCV34FM PVC VALVE 3/41n FPT X 3/41n MPT
PW10 3/4in BLACK POLY PRO X 10in- FPTBE – SCH.80
R25 AIR REGULATOR INCLUDES AIR FILTER AND BOWL
AFR25 AIR FILTER for R25
A8R25 METAL AIR BOWL for R25
S142058-VS 1/4-20 X 5/8 PHIL TRUSS MACHINE SCREW 18-8 W/#516 V1BRASEAL ORANGE

PATCH
5N1212| 1/2in HEX STAINLESS STEEL NIPPLE
5SAI4| SS304 MALE/FEMALE ADAPTOR 1/4 NPT X 1/4 NPT
SSAXLEI4| 14 %” long with the 5/8″ diameter bar & 2 through holes with countersinks beveled ends
SSC12| WORM GEAR CLAMP, S/S (.31-.91)
SSC38| WORM GEAR CLAMP, 5/S (.25-.63)
SS-MESH| STAINLESS STEEL MESH WITH SSST FOR REPLACEMENT
55P12| STAINLESS STEEL AXLE PLATE – 2.5 inch X 1 inch- 2 HOLE
SSST| SCREEN DISC .687 DIA. 10 X 10 MESH @ .020 DIA. 300 SERIES S.S.
SST12HB38| STAINLESS TEE COMBO 1/2in F PT X 3/8 in BARB WITH SSST AND S.S. MESH
5T80100| VEEIET NOZZLE, BRASS 80100
STR38-IL| IN UNE STRAINER 3/8 BARB 20 MESH 304 STAINLESS EDPM GSKT
TANK-10N| 10 GALLON NATURAL TANK
1W 916| 1/2 INT TOOTH L/W 410SS
W15| NONMARKING WHEEL FOR PORTABLE UNITS
W8| 1/4in S.S. WAND 71N SS TOE

Model No.: 910N, 910NK, 910NV

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals