BARSKA BE12592 Pro-200 Edition Metal Detector Instruction Manual

BARSKA BE12592 Pro-200 Edition Metal Detector

Product Information

Specifications

• Model: Pro-200 Edition Metal Detector
• Date: 2/20 BC638
• Power Source: 9V alkaline battery
• Usage: Outdoor only

Product Usage Instructions

Preparation

• Before using the metal detector, it is recommended to set the sensitivity to a median level.
• Adjust sensitivity lower in case of false signals.
• Ensure the detector is only used outdoors to avoid interference from electromagnetic waves.

Assembly

Assembling the detector requires no special tools.

Follow these steps:

1. Attach the top stem, middle stem, and lower stem.
2. Connect the search coil to the lower stem and tighten the knob.
3. Insert the lower stem into the middle stem and secure it with the lock nut.
4. Attach the control box to the top stem using the bolt.
5. Wind the cable around the stem and connect the search coil cable plug to the control box.
6. Adjust the stem length to your height and tighten the lock nut.

Installing Battery

1. Turn off the power switch on the control panel.
2. Open the battery compartment cover.
3. Connect the 9V alkaline battery, ensuring correct polarity.
4. Place the battery into the compartment and replace the cover.

FAQ

Q: Can I use the metal detector indoors?

• A: No, the detector is for outdoor use only.
• Indoor use may result in interference from electromagnetic waves emitted by electronic devices.

Q: How should I adjust the sensitivity of the detector?

• A: It is recommended to start with a median sensitivity level and adjust as needed.
• Lower sensitivity if experiencing false signals but remember that setting it too low may cause you to miss valuable targets.

Notes Before Use

• If you are new to using metal detectors, it is recommended to set the sensitivity to a median level. Lower the sensitivity slightly in the event of false signals.
• If the sensitivity is set too low, it may miss some valuable targets. After you have become familiar with the detector, you may try it at full sensitivity.
• This detector is for outdoor use only. Do not use indoors. Many home appliances can emit electromagnetic waves and will interfere with the detector.
• For indoor testing, keep the search coil away from electronics such as microwave ovens, computers, and TVs. If your detector beeps erratically, turn off the electronic appliances and lights, especially those with dimmer switches.
• Operates on one 9V alkaline battery (not supplied). Do not use heavy-duty batteries. Do not use ordinary Zinc-Carbon batteries.
• Read this manual before using it.

Treasure Hunter’s Code Of Ethics

• A few basic rules you should follow while using your detector
• Always get permission before searching any site
• Respect the rights and property of others
• Observe all national, state, and local laws when treasure hunting
• Never destroy historical or archaeological treasures. If you are not sure about an object you have found, contact a museum or historical society in your area.
• Leave the land and vegetation as is, and fill in any holes you dig.
• Use the detector only in safe areas
• Dispose of any junk you may find, only in approved areas. Do not leave it for the next treasure hunter find.

Preparation

Parts of the Metal Detector

Assembly

• Assembling the detector is easy and requires no special tools. Just follow these steps.

1. Top Stem (S Stem)
2. Middle Stem
3. Lower Stem
4. Search Coil
5. Control Box
6. Depress the spring clip in the middle stem (2) and insert it into the top stem (1) aligning the clip with the hole.
7. Unscrew the knobs on the lower stem (3) and remove the knob, washer and the connector. Insert the lower stem and align the holes on the search coil (4) bracket and the stem.

  * Push the connector through the holes and washer, then replace and tighten the knob.
3. Loosen the middle stem’s lock nut in the direction of the arrow. Then, insert the lower stem (3) into the middle stem (2). Turn the stem’s lock nut in the reverse direction of the arrow to lock it in place.
4. Unscrew the bolt of the control box (5) and hitch the control box to the top stem.
  * Then, insert the bolt into the assembly hole on the top stem and tighten it with the box.
5. Wind the cable around the stem. Insert the search coil cable plug into the five-pin jack at the bottom of the control box’s housing (5).
6. When you stand upright with the detector in your hand, the search coil is level with and about 0.5~2 inches / 1~5cm above the ground.
  * You can lengthen or shorten the stem based on your height.
  * After figuring out the suitable length, then tighten the lock nut.

Caution: The search coil cable plug fits into the connector only one way. Don’t force the plug or you could damage it.

Search Coil

Loosen the knobs at the search coil’s end; adjust the search coil to the desired angle. (The search coil should be parallel with the ground.) Tighten the knobs just enough to keep the search coil from rotating or wobbling.

INSTALLING BATTERY

You need one 9V alkaline battery to power your detector.

1. If the detector is on, turn the power switch (on the control panel) to POWER OFF.
2. Press on the battery compartment cover and slide the cover off in the direction of the arrow.
3. Connect the battery with the battery connector taking care of the polarity. Then put the battery into the compartment.
4. Replace the cover.

Cautions:

• Use only fresh batteries of the required size and recommended type.
• Always remove old or weak batteries; batteries can leak chemicals that can destroy electronic parts.
• If you do not plan to use the detector for a long time, remove the batteries.
• Dispose of old batteries promptly and properly.
• You can extend battery life by using earphones, which require less power than the built-in speakers.

Headphones

• You can connect a pair of headphones (not supplied) to the detector so you can listen privately. Using earphones also saves battery power and makes it easier to identify subtle changes in the sounds you hear, for better detection results.
• To connect the earphones to the detector, insert the earphone’s 3.5mm plug into the EAR jack on the control panel.
• Note: The detector’s internal speaker disconnects when you connect earphones.

Listening Safely

• To protect your hearing, follow these guidelines when you use earphones.
• Set the volume to the lowest setting before you begin listening.
• After you begin listening, adjust the volume to a comfortable level.
• Do not listen at extremely high volume levels. Extended high-volume listening can lead to permanent hearing loss.
• Once you set the volume, do not increase it. Over time, your ears adapt to the volume level, so a volume level that does not cause discomfort might still damage your hearing.

Traffic Safety

• DO NOT wear headphones while operating your detector near high-traffic areas.
• Even though some earphones are designed to let you hear some outside sounds when listening at normal volume levels, they still can present a traffic hazard.

Control Panel

fully counterclockwise to power off the unit.
SENS| Rotate the control clockwise to get higher sensitivity. Rotating it counterclockwise to decrease it.
DISC| Rotate the control clockwise away from ALL METAL to get DISC mode. The DISC mode comes with an auto ground balance. Rotate the control slowly and clockwise to eliminate different trash objects.
Rotate the control counterclockwise to the end to get ALL METAL mode. All METAL also comes with auto ground balance. It’s used to find not only ferrous metal but also non-ferrous one
VIEW METER| When the unit finds any metal target, the meter pointer swings to the right.
HEADPHONES| 3.5mm headphone jack for headphones.

Operation

Testing and Using the Detector

• The metal detector has two operation modes: ALL METAL & DISC. All metal is used to find all kinds of metal targets. DISC is used to discriminate the metal type.

1. To set the operation mode to ALL METAL: turn the DISC knob counterclockwise to the end and turn the SENS knob to a high position.
2. Then, hold the search coil parallel to the ground about .5-2 inches/ 1-5 cm above the surface. Sweep the search coil from side to side in an arc line of 2.75 inches/ 7 cm motion.
3. When the detector detects a buried target, it sounds a tone. Users can make a visual note of the exact spot on the ground where the detector beeps.
4. Stop the search coil directly over this point on the ground. Move the search coil straight forward away from you and straight back towards you a couple of times.
5. Meantime slowly rotate the DISC control clockwise away from ALL METAL until the unit does not sound or sound short tone. You can identify what kind of metal is REJECTED according to the setting position of DISC.

A reference for you to know what kind of metal is rejected depending on the DISC setting.

coin (1¢ 76 version)

• For example, if you set up a DISC knob to the position near midnight, it means that metal targets like Nickel coins, pull tabs, or Iron should be eliminated.
• Therefore, when you detect a buried target and the detector beeps, it may be the metal target of a Zinc coin, Copper Coin, or Silver.
• When the DISC control is set to the clockwise end most of the metal is rejected, except silver (25¢,50¢, and $1).
• Note: The above chart is for reference only.
• The actual result may be different for each metal detector.

Search Coil Sweeping Hints

• Never sweep the search coil as if it were a pendulum. Raising the search coil while sweeping or at the end of a sweep will cause false readings.
• Sweep slowly. Hurrying will cause you to miss targets.
• You should sweep the search coil from side to side in an arc line of 3 inches motion and keep the search coil parallel with the ground.

Factors That Affect The Detecting

• It’s difficult to have an accurate detecting result. It takes practice to get better detection results. Sometimes the detection may be restricted by some factors.
• If there is interference from other instruments or electrical cable, TV, or radio in your searching area, lower the sensitivity, or change the current searching area.
• When searching in highly mineralized areas, the unit will sound even if there’s no metal. In this case, you can lower the sensitivity and increase the height between the search coil and the ground until the false signal disappears.
• If necessary, reset the DISC.
• When searching in the trash area, it’s better to set the DISC to the 11:00 position, so that the unit can notch the most invaluable metals such as nails and small trashy irons.
• Move away any metal digging tool when searching.
• The sensitivity level is generally in contradiction with that of the discrimination.
• The higher the sensitivity level is, the worse the discrimination will be. But you can lower the sensitivity to have better discrimination.

Care and Maintenance

• Your metal detector is an example of superior design and craftsmanship.
• The following suggestions will help you care for your metal detector so you can enjoy it for years.
• Handle the detector gently and carefully. Dropping it can damage circuit boards and can cause the detector to work improperly.
• Use the detector only in normal temperature environments.
• Temperature extremes can shorten the life of electronic devices, causing internal damage to the detector.
• Keep the detector away from dust and dirt, which can cause premature wear and tear of parts.
• Wipe the detector with a damp cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the detector.

CAUTION:

• The search coil is waterproof, and it can be completely under freshwater or seawater.
• Please be careful to avoid the water entering into machine’s body.
• Sea water may erode the search coil. Please always use fresh water to clean the search coil after detection in seawater.
• Change or damage to the inner components will cause the detector to fault, and such a fault is not within our warranty.

Troubleshooting

Sweeping the detector’s search coil too fast or at the wrong angle.

| Sweep the search coil more slowly and hold the detector correctly. For more details, please see the section of “Testing and Using
Using 2 detectors close| Keep two detectors at least 6 meters(20’) apart
Function.| Five-pin cable not connected well| Replug it properly.
Dead battery| Replace batteries

Reassemble the Locknut For the Metal Detector

• If you encounter a problem inserting the lower stem into the upper stem, please reassemble the locknut by following the steps below

1. Turn the lock knob clockwise to lose it from the upper stem (see image 1)
2. Place the lock knob on the lower stem and make the small head toward the search coil (see image 2)
3. Insert the lower stem into the top stem. Make sure that the lower stem completely inserts into 3 sections of plastic pieces (see image 3)
4. Move the lock knob upwards and turn counter-clockwise until the locknut lock-in place (see image 4)

• ©2020 BARSKA®

• 855 Towne Center Drive

• Pomona, CA 91767

• (t) 888.666.6769
  (f) 909.445.8169

• www.barska.com

Documents / Resources

| BARSKA BE12592 Pro-200 Edition Metal Detector [pdf] Instruction Manual
BE12592 Pro-200 Edition Metal Detector, BE12592, Pro-200 Edition Metal Detector, Edition Metal Detector, Metal Detector
---|---

References

• Your Trusted Source for Security Solution and Precision Optics – Barska

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>