COLBOR CL220R Video Light User Manual
- June 17, 2024
- COLBOR
Table of Contents
COLBOR CL220R Video Light
Thank you for choosing the COLBOR product. Please read this manual carefully before use and follow all instructions mentioned herein.
Caring For Your COLBOR Product
- Keep corrosive chemicals, liquids and heat sources away from the product to prevent mechanical damage.
- The product is not waterproof.
- Do not leave the product unattended while in use. Keep out of reach of children.
- Do not handle it with wet hands. Do not touch the hot COB surface.
- Please do not block the ventilation and do not look at the light directly when it is on.
- Do not attempt to disassemble or modify the product. Doing so voids the warranty.
- Please have the product checked or repaired by authorized technicians if any malfunctions happen.
- Disconnect from the power supply when it is not in use.
- Do not cover, inverted COB and radiator for high temperatures, do not cover, inverted, do not touch the lamp holder and radiator vent with your hands when the product is in use.
- Do not use any power adapter of other products to avoid the lamp malfunction.
- Malfunction may be caused by dropping, the impact of external force.
- Failure to follow all the instructions may result in mechanical damage.
- Our company reserves the right of the final interpretation of the product.
- Product design and specifications are subject to change without prior notice.
Power Connection
You must use the power adapter that comes with the product rather than other adapters to avoid damaging the lamp. The positive and negative connections of the power adapter interface( DC OUT) and the lamp power interface (DCIN) are shown below:
Product Instructions
- LED Display Screen
- EFF Mode Button
- EFF Rate Option Button
- Mode Button
- Settings Menu Button
- Left Knob/Option Adjustment Knob
- Right Knob/Parameter Adjustment Knob
- DC 48V Power Port
- Power Button
- Bowens Mount Lock
- Light Source
- Lamp Angle Adjustment Locking Grip
- Lamp Holder
- Air Outlet
- NATO Rail
- Air Inlet
- Lamp Handle
- Umbrella Hole
- Umbrella Hole Screw
- Lamp Holder Screw
Light Installation
Removal of lamp cap protection cover
Hold the COB cover with the Bowens Mount tenon and rotate it in the direction
of the arrow.
Note: Be sure to remove the cob protective cover and cob protective film
before use.
Installation and removal of reflector
- Installation of reflector: Align the reflector with the groove around the lamp head and clip it in, turn the reflector in the direction of the arrow, and the reflector installation will be completed after the top rod rebounds.
- Removal of reflector: Please follow the instructions below.
Installation of light
- Rotate the lamp holder screw until the inner wall is not shielded and put the product on the top of the lamp holder to tighten the bracket screw for fixation. Adjust the lamp body irradiation angle and tighten the lamp holder angle grip.
Install the soft light umbrella
- Insert the handle of the soft light umbrella into the umbrella hole and tighten the screw to lock.
Power Supply
- Power cord adapter fixation Pass the attached wire rope through the snap ring of the power adapter and hang it on the stand.
- AC power supply Connect the power adapter, aim the pin at the DC power interface of the lamp body, and then power on after the cable is well-placed.
- Power cord storage When pulling out the power cord of the lamp body, firstly press the spring beside the connector to unlock it. Do not pull out the wire forcefully without unlocking it.
- Power with V-port battery Attach the V-mount battery to the lamp with the NATO expansion bar and VM3 (optional), then connect the D-tap to XLR power cord, and power on the lamp.
Note
For one 14.8V battery powering, the maximum brightness is 50% of full power.
Operation Instructions
- Remove the COB protective cover before powering the light.
- Power On: After confirming that the power connection is finished, press the switch to “-”, and the screen will display the brand and product module. (Default mode: CCT)
- Power Off: Press the switch to “o” to turn it off.
Status Icon Description
① APP Connection Status Icon
| After selecting wireless connection in the Settings menu, the icon will be
displayed dynamically.
****| The icon is always on to indicate a successful pairing with the mobile
APP.
The icon disappears to indicate mobile APP pairing failure, or the product is unpaired.
② Fan Status Icon
| Smart Mode. The product will adjust the fan speed according to the
internal detected temperature to ensure that it is in optimal working
condition.
| Quiet Mode. The fan keeps running at a low speed for minimum noise, and
overheating protection will be activated if the product temperature is higher
than the alarm value.
| Performance Mode. The fan runs at the highest speed to ensure heat
dissipation.
③ Group Status Icon
| No grouping status. The product defaults to the factory status, and
will not be affected by other groups.
| Stands for Group A. There are fifteen groups (A~O). T stands for Tx.
| Stands for Group A. There are fifteen groups (A~O). R stands for Rx.
****| Stands for Group A. There are fifteen groups (A~O). TR stands for TxRx.
④ Product Overheated Alarm Icon
****| If the icon flashes, it means that the internal temperature
of the product is too high, and cooling measures need to be taken. If the icon disappears, it means that the operation is normal.
CCT Mode (Short press Mode Button to switch CCT Mode and HSI Mode)
Default: CCT Mode
HSI Mode (Short press Mode Button to switch)
EFF-CCT Mode (Short press EFF Button )
Default: EFF-CCT Mode
EFF-HSI Mode (Short press EFF Button then press the left knob to switch to EFF-HSI Mode.)
Setting
- Short press the SET bottom to enter the settings menu.
- Roll the Brightness Control Wheel to choose settings.
- Press the setting bottom to adjust the corresponding setting(Short press the setting bottom to adjust the wireless connection mode).
APP Connection & Light Control
Scan the QR code， or search “COLBOR STUDIO” in the app store to download the
app for light control.
CL220R Pairing
- Press the setting button and enter the pairing mode. Short press the setting button to choose “APP”, then long press the setting button for 3 seconds for pairing.
- Open the APP and click the “ + ” on the upper right, then click the scene one and click the + on the upper right. Showing CL220R means successfully pairing.
- Click the CL220R for control.
CL220R Group Control
- After successfully pairing the CL220R, click the group then click the“ + ” on the top right. Choose the light for grouping and click the confirm button. Showing Group One means successfully grouping.
- Click the group for lighting control.
Equipped with a NATO extension bar and an NQD quick-release device, the lights can be spliced together, and up to three lights can be spliced.
Specifications
- Type: Bi-Color + RGB
- Colour Temperature Range: 2700K-6500K（±200K）
- CRI/TLCI: 96±2/97±2
- TM-30-18: Rf:94±2/Rg:102±2
- SSI: 83(D32)/73(D56)
- Illumination: See the Form 1 Below
- Beam Angle: No Reflector ≈∠ 120°
- Power: 250W（Max）
- COB Output Power: C/W:220W R/G/B: 100W *Constant Power Output
- Input: DC 48V 5.2A 3 Pin XLR
- Body Material: Aluminum Alloy+ABS
- Size (LWH): 240128219mm (9.4″5″8.6″)
- Weight: 1.6kg(3.52lbs)
- Op. Temp: -10~40℃
Package List
Power adapters may vary according to sales region.
Form 1
Illumination
CCT
|
Distance
| Light Base| BHR15
Reflector
| BHR45
Reflector
| BSR70
Reflector
| BSR70
+Softbox
---|---|---|---|---|---|---
2700K
| 1m| 6100| 47200| 26200| 7570| 3980
3m| 915| 4800| 2380| 1020| 529
5m| 424| 1890| 1040| 492| 257
3200K
| 1m| 6370| 49400| 27400| 7950| 4140
3m| 938| 5020| 2490| 1070| 552
5m| 443| 1980| 1090| 514| 269
4300K
| 1m| 6840| 53100| 29500| 8550| 4420
3m| 1090| 5390| 2670| 1150| 588
5m| 475| 2130| 1170| 551| 284
5600K
| 1m| 7100| 55300| 30600| 8920| 4570
3m| 1130| 5590| 2770| 1190| 608
5m| 493| 2210| 1220| 572| 295
6500K
| 1m| 7260| 56300| 31400| 9070| 4770
3m| 1150| 5680| 2840| 1220| 621
5m| 505| 2260| 1240| 582| 300
The data is given from testing in a laboratory.
WARRANTY
Warranty Period
Thank you for purchasing COLBOR products.
- Customers are entitled to free replacement or repair service in case of the quality defect(s) found in the product under normal use within 30 days of receipt of the product.
- Original COLBOR products are entitled to a 12-month limited warranty service.
The warranty period begins on the date of purchase of brand-new, unused products by the first end-user.
Within the warranty period, if a product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations
- Faults result from inappropriate use of a product without following its operation specification.
- Artificial damage, e.g. crash, squeeze, scratch, soaking, exposure to rain or dampness.
- Modifications to a product by its user or a third party without prior written consent of COLBOR, e.g. replacement of element or circuit, label alteration.
- The code on the product is inconsistent with that of the warranty certificate, or the code on the product or warranty certificate is altered or torn off.
- All consumable accessories attached to a product, like cable, cover
- Faults as a result of force majeure, such as fire, flood, lightning, etc.
Warranty Claim Procedure
- If failure or any problem occurs with your product after purchase, please contact a local agent for assistance, or you can always contact COLBOR’s customer service through email.
- Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided.
- If the COLBOR product is out of warranty coverage, the service and the cost of the part will be charged.
CONTACT
Guangzhou Zhiying Technology Co., Ltd
- Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue,
- Liwan District, Guangzhou, China, 510000
- support@colborlight.com.
- www.colborlight.com.