ARRMA ARA5210B 1/5 OUTCAST 4WD EXtreme Bash Roller Stunt Truck, Black User Manual
- June 4, 2024
- ARRMA
Table of Contents
- Safety Precautions and Warnings
- WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
- Support
- Kit Overview
- Required
- Recommended Tools
- How To…
- Remove Body
- Install AA Batteries In the Controller
- Install Charged Batteries In Car
- Steering Neutral
- How to Drive
- Connect ESC and Power On
- Install Car Body
- Power off
- Storage
- Maintenance Schedule
- Maintenance
- LIMITED WARRANTY
- Warranty and Service Contact Information
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ARA5210B 1/5 OUTCAST 4WD Extreme Bash Roller Stunt Truck, Black
User Manual
NOTICE All instructions, warranties, and other collateral documents are
subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date
product literature, visit horizonhobby.com or towerhobbies.com and click on
the support or resources tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate
various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the
probability of property damage, collateral damage, and serious injury OR
create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the
probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility
of physical property damage AND a little or no possibility of injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product
correctly can result in damage to the product, and personal property and cause
serious injury.
This is a sophisticated hobby product. It must be operated with caution and
common sense and requires some basic mechanical ability. Failure to operate
this Product in a safe and responsible manner could result in injury or damage
to the product or other property. This product is not intended for use by
children without direct adult supervision. Do not use incompatible components
or alter this product in any way outside of the instructions provided by
Horizon Hobby, LLC. This manual contains instructions for safety, operation,
and maintenance. It is essential to read and follow all the instructions and
warnings in the manual, prior to assembly, setup, or use, in order to operate
correctly and avoid damage or serious injury.
WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum products. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.
Age Recommendation: Not for children under 14 years. This is not a toy.
Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a
manner that does not endanger yourself and others or result in damage to the
product or property of
others.
This model is controlled by a radio signal subject to interference from many
sources outside your control. This interference can cause momentary loss of
control, so it is advisable to always keep a safe distance in all directions
around your model as this margin will help avoid collisions or injury.
- Never operate your model with low transmitter batteries.
- Always operate your model in open spaces away from full-size vehicles, traffic, and people.
- Never operate the model in the street or in populated areas for any reason.
- Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.) you use.
- Keep all chemicals, small parts, and anything electrical out of the reach of children.
- Never lick or place any portion of the model in your mouth as it could cause serious injury or even death.
- Exercise caution when using tools and sharp instruments.
- Take care during maintenance as some parts may have sharp edges.
- Immediately after using your model, do NOT touch equipment such as the motor, electronic speed control, and battery, because they generate high temperatures. You may burn yourself seriously touching them.
- Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury.
- Always turn on your transmitter before you turn on the receiver in the car. Always turn off the receiver before turning your transmitter off.
- Keep the wheels of the model off the ground when checking the operation of the radio equipment.
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
Your new Horizon Hobby vehicle has been designed and built with a combination
of waterproof and water-resistant components to allow you to operate the
product in many “wet conditions” including puddles, creeks, wet grass, snow,
and even rain.
While the entire vehicle is highly water-resistant, it is not completely
waterproof and your vehicle should NOT be treated like a submarine. The
various electronic components used in the vehicle, such as the Electronic
Speed Control (ESC), servo(s), and receiver are waterproof, however, most of
the mechanical components are water resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws, and nuts, as well as
the contacts in the electrical cables, will be susceptible to corrosion if
additional maintenance is not performed after running in wet conditions.
To maximize the long-term performance of your vehicle and to keep the warranty
intact, the procedures described in the “Wet Conditions Maintenance” section
below must be performed regularly if you choose to run in wet conditions. If
you are not willing to perform the additional care and maintenance required,
then you should not operate the vehicle in those conditions.
CAUTION: Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.
General Precautions
- Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle.
- Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Caution should be taken when using Li-Po batteries in wet conditions.
- Most transmitters are not water-resistant. Consult your transmitter’s manual or the manufacturer before operation.
- Never operate your transmitter or vehicle where lightning may be present.
- Do not operate your vehicle where it could come in contact with salt water (ocean water or water on salt-covered roads), or contaminated or polluted water. Saltwater is very conductive and highly corrosive, so use caution.
- Even minimal water contact can reduce the life of your motor if it has not been certified as water-resistant or waterproof. If the motor becomes excessively wet, apply a very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor.
- Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time.
Wet Conditions Maintenance
-
Drain any water that has been collected in the tires by spinning them at high speed. With the body removed, place the vehicle upside down and pull the full throttle for a few short bursts until the water has been removed. See page 31.
CAUTION: Always keep hands, fingers, tools, and any loose or hanging objects away from rotating parts when performing the above drying technique. -
Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing. Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle. -
Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners.
-
Spray the bearings, drive train, fasteners, and other metal parts with a water-displacing light oil. Do not spray the motor.
-
Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.
-
Increase the frequency of disassembly, inspection, and lubrication of the following:
– Front and rear axle hub assembly bearings.
– All transmission cases, gears, and differentials.
– Motor—clean with an aerosol motor cleaner and re-oil the bearings with lightweight motor oil.
Support
At ARRMA we want you to love running your kit and make owning a high- performance RC car as simple as possible. If you have any questions about running, maintaining, tuning, or repairing your ARRMA product there are two options for you to use to get help and advice. Visit ARRMA-RC.com for support, parts, and upgrades for your kit. If you can’t find what you’re looking for then you can always email us at supportUSA@ARRMA-RC.com (USA) or support@ARRMA-RC.com (ROVV) 24hrs a day and we will do our best to help you with your query.
Kit Overview
SPECIFICATIONS
ARRMA OUTCAST™ 8S (ARA5210)
Length | 714mm / 28.11 in |
---|---|
Width | 596mm / 23.46 in |
Height | 305mm / 12.01 in |
Wheelbase | 430mm / 16.93 in |
Battery Tray MAX dims | L:170mm / 6.69 in x W:55mm / 2.16 in x H:53mm / 2.08 in |
Weight | 10.5kg / 23.10Ibs |
Required
Battery Tray MAX dims| L:170mm / 6.69 in x W:55mm
/ 2.16 in x H:53mm / 2.08 in
---|---
Recommended Tools
Tools required will appear in this box
Online Videos are Available when you see this icon
How To…
Install Servo in Receiver box
The below steps will help you to choose and select the correct servo for the vehicle and install it in the correct mount.
Fitting your servo to the correct mount
Install the Receiver in the Receiver box
Max.
A | Length | 55.5mm / 2.18 in |
---|---|---|
B | Width | 31mm / 1.22 in |
C | Height | 25.5mm / 1.00 in |
Install ESC on Receiver box lid
The below steps will help you to install your chosen 8S Electronic Speed Control to the Receiver Box lid.
Install the servo saver
The below steps will help you to install the servo saver and radio box module into the car.
Change the Spur Gear
The below steps will help you select the correct spur gear for the vehicle and install it. Follow gearing advice from your chosen motor manufacturer.
2 spur gears are included in the kit.
ARA31 0920 S PURGEAR 47T (1pc)
ARA31 1051 S PUR GEAR 39T (1pc)
Gear Ratio Chart
Pinion Gear (Mod 1)|
---|---
49 Series Motor| | | 15| 16| 17| 18| 19| 20| 21| 22| 23| 24| 25| 26| 27| 28|
29| 30| 31| 32| 33| 34| 35| 36| 37| 38 39
Spur Gear| 47|
28.4
|
26.6
|
25.0
|
23.7
|
22.4
|
21.3
|
20.3
|
19.4
|
18.5
|
17.7
|
17.0
|
16.4
|
15.8
|
15.2
|
14.7
|
14.2
|
39| |
18.6
|
17.7
|
16.8
|
16.1
|
15.4
|
14.7
|
14.1
|
13.6
|
13.1
|
12.6
|
12.2
|
11.8
|
11.4
|
11.0
|
10.7
|
10.4
|
10.1
|
9.8
|
9.5
|
9.3
|
9.1
Pinion Gear (Mod 1)|
---|---
56 Series Motor| | | 15| 16| 17| 18| 19| 20| 21| 22| 23| 24| 25| 26| 27| 28|
29| 30| 31| 32| 33| 34| 35| 36| 37| 38 39
Spur Gear| 47|
28.4
|
26.6
|
25.0
|
23.7
|
22.4
|
21.3
|
20.3
|
19.4
|
18.5
|
17.7
|
17.0
|
16.4
|
15.8
|
15.2
|
14.7
|
14.2
|
13.7
|
39| | |
18.6
|
17.7
|
16.8
|
16.1
|
15.4
|
14.7
|
14.1
|
13.6
|
13.1
|
12.6
|
12.2
|
11.8
|
11.4
|
11.0
|
10.7
|
10.4
|
10.1
|
9.8
|
9.5
|
9.3
|
9.1
Once you have chosen your motor (Kv) follow the motor manufacturer’s
recommendations on gear ratio. Use the gear ratio table to select the spur
gear that will allow you to achieve the motor manufacturers’ recommended gear
ratio.
CAUTION: Monitor your motor temps to keep within the motor manufacturer’s
guidelines
Install the motor
The below steps will help you to install the motor into the vehicle. Choose your motor plate based on your motor dimensions.
2 motor plates included in the kit.
Max.
A | Length | 113mm / 4.44 in |
---|---|---|
B | Diameter | 49mm / 1.92 in |
A | Length | 113mm / 4.44 in |
---|---|---|
B | Diameter | 56mm / 2.20 in |
Remove Body
Install AA Batteries In the Controller
CAUTION: If using rechargeable batteries, only charge rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property. Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.
Install Charged Batteries In Car
Steering Neutral
How to Drive
Connect ESC and Power On
Install Car Body
Power off
Storage
Maintenance Schedule
We recommend a Service Schedule to keep your vehicle in the best working condition possible. Our recommended schedule appears as the below icon:
Maintenance
Wheel and Tire Maintenance
Check the areas highlighted in the image to the left after the duration of usage above. Replace parts where necessary to ensure maximum durability and enjoyment from your vehicle.
Pivot Ball Maintenance
Check the areas highlighted in the image to the left after the duration of usage above. Replace parts where necessary to ensure maximum durability and enjoyment from your vehicle.
Shock Maintenance
Check the areas highlighted in the image to the left after the duration of usage above. Replace parts where necessary to ensure maximum durability and enjoyment from your vehicle.
Center Different Maintenance
Check the areas highlighted in the image to the left after the duration of usage above. Replace parts where necessary to ensure maximum durability and enjoyment from your vehicle.
F/R Different Maintenance
Check the areas highlighted in the image to the left after the duration of usage above. Replace parts where necessary to ensure maximum durability and enjoyment from your vehicle.
Driveshaft Maintenance
Check the areas highlighted in the image to the left after the duration of usage above. Replace parts where necessary to ensure maximum durability and enjoyment from your vehicle.
How To…
Change the Pinion/Motor
The below steps will help you to change the pinion which will alter the speed of the vehicle. Removing the motor can also be done at the same time.
Adjust Ride Height
The below steps will help you to adjust the vehicle’s ground clearance to suit the terrain you choose to drive on.
Vent your tires
The below steps will show you how to vent your tires when driving in wet or sandy conditions.
The wheels on your pre-glued tires have air holes drilled as standard. This allows the tires to breathe and provides the best performance for general bashing. If you want to drive your vehicle in wet or dusty/sandy environments then we suggest making the following modifications.
LIMITED WARRANTY
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product’) will be free from defects in materials and workmanship for a period of 2 years from the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation, or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, (vi) Product not compliant with applicable technical regulations, or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event, shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup, or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, the purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law principles). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup, or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www. horizonhobby.com, submit a Product Support Inquiry, or call the toll-free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/service-center render- service-center. If you do not have Internet access, please contact Horizon Product Support to obtain an RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address, and phone number where you can be
reached during business hours. When sending the product to Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issues with a LiPo battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
Non – Warranty Service
Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of/, hour of labor. In addition, you will be billed for return freight Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/content/ service-center render-service-center.
ATTENTION: Horizon service is limited to Product compliance In the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging the return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Products for a period of 60 days from notification, after which they will be discarded. 10/2015
Warranty and Service Contact Information
Country of Purchase| Horizon Hobby| Contact Information|
Address
---|---|---|---
United States of America| Horizon Service Center (Repairs and Repair
Requests)|
servicecenter.horizonhobby.com/RequestForm/|
2904 Research Road Champaign, Illinois 61822 USA
Horizon Product Support (Product Technical Assistance)|
productsupport@horizonhobby.com
877-504-0233
Sales| websales@horizonhobby.com
800-338-4639
Horizon Technischer Service|
service@horizonhobby.eu
+49 (0) 4121 2655 100| Hanskampring 9
D 22885 Barsbilttel, Germany
Sales: Horizon Hobby GmbH
ARB100028825
ARRMA-RC.COM
©2021 Horizon Hobby, LLC. ARRMA RC is a trading name of Horizon Hobby Ltd.
Horizon Hobby Ltd is a subsidiary of Horizon Hobby, LLC. ARRMA, the ARRMA
logo, OUTCAST, DSMR, DMS2, EC5, IC5, AVC, Active Vehicle Control, dBoots, and
the Horizon Hobby logo are trademarks or registered trademarks of Horizon
Hobby, LLC. The Spektrum trademark is used with permission of Bachmann
Industries, Inc. Twitter® logos are trademarks of Twitter, Inc. Facebook®, and
its logo are trademarks or registered trademarks of Facebook, Inc. The
YouTube® logo is a trademark of Google Inc. All other trademarks or registered
trademarks are the property of their respective owners.
References
- ARRMA RC Cars and RC Trucks - Designed Fast, Designed Tough | ARRMA
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
- Ferngesteuerte Flugmodelle, Autos, Trucks, Hubschrauber, Boote und Fernsteuerungen | Horizon Hobby
- Horizon Hobby Service Center
- RC Cars, RC Trucks, RC Airplanes, Model Trains, and Slot Cars at Tower Hobbies
- ARRMA RC Cars and RC Trucks - Designed Fast, Designed Tough | ARRMA
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>