TAC-CDS9-007 Sniper Running Boards Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC-CDS9-007 Sniper Running Boards
Specifications:
- Installation Time: 60-120 minutes
- Cutting: Not Required
- Drilling: Not Required
- Part List:
- SNIPER RUNNING BOARD
- PART #: TAC-CDS9-007
- FITS:
- 2019-Up Chevy Silverado 1500 Regular Cab
- 2020-Up Chevy Silverado 2500-3500 Regular Cab
- 2019-Up GMC Sierra 1500 Regular Cab
- 2020-Up GMC Sierra 2500-3500 Regular Cab
- Torque & Tools:
- Fastener Size: 6mm, 8mm, 10mm, 12mm
- Tightening Torque (ft-lbs): 7-8.5, 18-20, 35-40, 60-70
- Wrench Required: 10mm, 13mm, 16mm, 18mm
- Allen Wrench Required: 4mm, 5mm, 6mm, 8mm
Product Usage Instructions
Before Installation:
- Remove contents from the box and verify all parts are present.
- Read instructions carefully before starting installation.
Assistance is recommended.
Installation Steps:
Step 1:
Start the installation under the Passenger/Right side of the vehicle. Remove
the plastic plugs to uncover threaded holes in the floor.
Step 2:
Attach Mounting Brackets to the threaded mounting holes. Thread an 8mm Hex
Bolt into the threaded holes to clear paint as required.
Step 3:
Attach the Passenger/Right Mounting Bracket to the factory threaded holes
using the provided hardware. Do not tighten hardware yet.
Step 4:
Move along the body to the next mounting location and repeat Steps 1 – 3 for
the remaining Passenger/Right Mounting Bracket.
Step 5:
Attach the Passenger/Right Running Board to the Mounting Brackets using the
provided Combo Bolts. Do not slide the Running Board front to back.
Step 6:
Level and adjust the Running Board and fully tighten all hardware.
After Installation:
Do periodic inspections to ensure all hardware is secure and tight. Avoid
using polish or wax with abrasives that could damage the finish. Mild soap may
be used for cleaning.
FAQ:
Q: What should I do if I encounter missing parts during installation?
A: If you find any missing parts, please contact customer support at tac-
office@tacautoparts.com for assistance.
SNIPER RUNNING BOARD
PART #: TAC-CDS9-007
FITS:
2019-Up Chevy Silverado 1500 Regular Cab 2020-Up Chevy Silverado 2500-3500
Regular Cab 2019-Up GMC Sierra 1500 Regular Cab
2020-Up GMC Sierra 2500-3500 Regular Cab
Torque & Tools
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
Part List
TOOLS
PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE PASSENGER-SIDE INSTALLATION
INSTRUCTION
STEP 1
Start the installation under the Passenger/Right side of the vehicle.
Locate the 4 plugs along the bottom edge of the body. Remove the plastic plugs
from each mounting location, (Fig 1).
STEP 2
Mounting Brackets will attach to all threaded mounting holes, (Fig 2).
Directly above each threaded hole is a top mounting location on the side of
the body panel. Hold a Bracket up in place to help determine the mounting
holes to use along the body. NOTE: Thread an 8mm Hex Bolt into the threaded
holes to clear paint as required.
STEP 3
Select (1) Passenger/Right Mounting Bracket. Attach the Mounting Bracket to
the factory threaded holes with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and
(2) 8mm Flat Washers, (Fig 3). Do not tighten hardware.
STEP 4
Move along the body to the next mounting location. Repeat Steps 1 – 3 to
attach the remaining (1) Passenger/Right Mounting Bracket to the remaining
rear locations.
STEP 5
Select the Passenger/Right Running Board.
NOTE: The Passenger/Right Running Board will have a “07-R” on the front. Place the Running Board onto the Mounting Brackets.
IMPORTANT: Do not slide the Running Board front to back or damage to the finish may result. Attach the Running Board to the Mounting Brackets with (8) 8mm Combo Bolts, (Fig 4).
STEP 6
Level and adjust the Running Board and fully tighten all hardware.
STEP 7
Repeat Steps 1—6 to attach the Driver/Left Running Board.
STEP 8
Do periodic inspections to the installation to make sure that all hardware
is secure and tight.
Attention
To protect your investment, do not use any type of polish or wax that may
contain abrasives that could damage the finish.
Mild soap may be used also to clean the Running Boards.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>