Eastar EVA-1 Full Size Violin Set Owner’s Manual
- June 17, 2024
- Eastar
Table of Contents
EVA-1 Full Size Violin Set
Owner’s Manual
EVA-1 Full Size Violin Set
Eastar Violin
Owner’s Manual
Thank you for choosing Eastar violin!
Now, please follow the guide and set up your instrument.
Violin’s Construction
Product List
Model | EVA-1 | EVA-2 | EVA-3 | EVA-330 |
---|---|---|---|---|
Name | Quantity | Quantity | Quantity | Quantity |
Violin | 1 pc | 1 pc | 1 pc | 1 pc |
Bow | 1 pc | 1 pc | 1 pc | 2 pcs |
Strings | 2 sets (1 set already installed) | 2 sets (1 set already installed) | 2 | |
sets (1 set already installed) | 2 sets (1 set already installed) | |||
Shoulder rest | 1 pc | 1 pc | 1 pc | 1 pc |
Rosin | 1 pc | 1 pc | 1 pc | 1 pc |
Bridge | 1 pc | 2 pcs | 2 pcs | 1 pc |
Case | 1 pc | 1 pc | 1 pc | 1 pc |
Manual | 1 pc | 1 pc | 1 pc | 1 pc |
Tuner | 1 pc | / | 1 pc | 1 pc |
Violin Specifications
Model | EVA-1 | EVA-2 | EVA-3 | EVA-330 |
---|---|---|---|---|
Size available | 1/4.1/2.3/4.4/4 | 1/4.1/2.3/4.4/4 | 1/4.1/2.3/4.4/4 | 4/4. |
Fingerboard | Ebony | Pear wood with learning point | Pear wood with learning | |
point | Pear wood | |||
Body | Spruce/Maple | Spruce/Maple | Spruce/Maple | Spruce/Maple |
Pegs | Maple | Jujube wood | Jujube wood | Jujube wood |
Tailpiece | Aluminum alloy with fine tuners | Aluminum alloy with fine tuners | ||
Aluminum alloy with fine tuners | Aluminum alloy with fine tuners | |||
Chinrest | Maple | Jujube wood | Jujube wood | Jujube wood |
Strings | Steel | Steel | Steel | Steel |
Finish | Natural varnish | Natural varnish | Matte antique finish | Matte antique |
finish
Bow| Brasilia wood| Brasilia wood| Brasilia wood| Brasilia wood
Shoulder rest| ABS| ABS| ABS| Natural: Wood Black: ABS
Set the Bridge
A violin bridge is a small piece of wood. The bottom of the bridge is usually a straight line, while the top is arched slightly. When examining your bridge, you’ll notice that one side of the arch is slightly higher than the other. The lower side is the E-string side, and the taller side is the G-string side. When you put the bridge in place, make sure the E-string comes over the E-string side, and the G-string comes over the G-string side. If you don’t know which strings are which, the G-string will be the string farthest to the left when the violin’s head is facing your body, and the E-string will be the string farthest to the right.
Place the bridge between the F-holes.
The F-holes are two f-shaped holes found near the end of the violin’s head.
When you slide the bridge under the strings, make sure it’s between the two
F-holes. The bridge should be placed at roughly the midway point of the
f-holes.
Put the violin strings in the knobs of the bridge.
The violin bridge has four small knobs running across the top. The four violin
strings fit into these knobs, keeping the bridge and the strings in place.
Gently feed one violin string at a time into the knobs on the bridge.
Tighten the strings.
Now you can retighten your strings to keep the peg in place. Gently turn each
peg on the head of the violin. It’s a good idea to use one hand to hold the
bridge in place while tightening the strings, to prevent it from falling over.
Tighten the strings until they are secure enough to keep the bridge in place
while still having a very slight amount of slack.
- Check to the bridge is in the center of the violin and make sure the bridge is standing at a 90-degree angle and falls roughly in the middle of the f-holes.
- Bridges often fall out of place during first tuning. To prevent this from happening, make sure you hold your bridge in place with one hand when tuning.
Tune the Strings
Check the peg, and make sure the peg is not too loose or too tight.
Take the peg and push it back into its proper place on the pegbox. Rotate the
peg in a circle to spread the peg compound around the edges of the hole, which
will make it easier to spin and adjust your tuning peg.
Pluck a note on the “A” string.
Use your fingers to pick at the string, striking a note. The tuner dial will
move up and down to show you where the note is. Make sure the note says “A” in
the corner when you pluck the string. If it doesn’t, you’ll need to make a lot
of adjustments.
Turn the pegs to make larger adjustments.
Find the corresponding peg for the string. For the “A” string, it’s the one
that’s at the top right if you’re holding the violin facing you with the pegs
at the top. Move clockwise to make it higher or counterclockwise to make the
note lower. Make small moves, less than 0.25 inches (0.64 cm) at a time to
adjust the pitch.
- The strings are typically tuned to G-D-A-E from left to right, pushing the peg in securely while turning the peg firmly.
Attach the Shoulder Rest
Hold the violin between your legs.
Take your violin with both hands and place it between your legs. With the back
facing you and the scroll pointing to the floor. The body of the violin will
be pointing toward the ceiling. Your legs should fit nicely in the rib area of
the violin. Squeeze your legs ever so slightly to hold the violin in place.
Attach the feet of the shoulder rest to the violin.
Take the shoulder rest. Place the wider part onto the same side of the
chinrest. Make sure that the rim of the violin fits nicely into the c shape of
the feet on the rest. Slide the feet of this wider side to a 9’o clock
position. Slide the other feet onto the outside of the violin stopping at
sound the 3’o clock position.
Adjust the placement of the feet of the shoulder rest.
Adjust it by sliding the feet to an angle that fits your shoulder. Make sure
it is secure. If your shoulders are narrow, move the feet closer to the end
pin. If you have wider shoulders, place the shoulder rest further away from
the end pin, in the middle of the lower body of the violin.
Rosin Your Bow
Grab your rosin block and scratch it to bring rosin powder to the top.
Scratch the rosin by using the screw of the bow or a nail file on the surface
of the rosin.
Tighten your bow and start putting rosin on the bow hair.
Tighten the bow until you see the middle part of the bow is slightly curved,
like a smile. Otherwise, you will determine that the violin bow is over-
tightened when the wood has lost its curve in the middle part of the bow and
gone completely straight.
“Play” the rosin back and forth.
Run the bow along the rosin from the tip down to the frog (the part you hold
with your hand), and then stroke it back again. Grasp the bow gently and press
down just hard enough that the bow hairs produce some dust and feel the bow
gripping and no longer slipping.
Care and Maintenance
Store a violin
As a rule, the safest place to keep a violin is in its violin case. The
temperature of the room should be constant and the humidity moderate. During
the heating season it may be advisable to use a humidifier to prevent damage
to the gluing or, even worse, cracks in the wood.
A violin should be kept in a place free of drafts and away from direct
sunlight. Make sure that the violin case is neither “in the way” where it can
get knocked over in passing, nor kept on a shelf or in a closet where it can
fall down when other items are retrieved. When placing the violin in its
violin case, make sure that no sharp or pointed objects can damage the
varnish.
Caution: the violin should never be put under pressure or forced into its
case!
Clean a violin
Rosin dust can damage the instrument varnish if it is not wiped away after
each playing session. And should always be wiped off the strings and
fingerboard as well. For this purpose, it is best to use a soft cloth. Avoid
using the same cloth to clean the rest of the body, as any rough flakes of
rosin that may be sticking to the cloth could scratch the varnish, and a fine
layer of rosin dust from the cloth would be distributed all over the
instrument, eventually dulling the varnish.
About the peg
Temperature changes will cause the wood of the pegs to contract or expand. if
the peg easily to slipping, please plug inside energetically while tuning and
rotation. If too tight, Peg lubricant helps stiff pegs turn more smoothly and
can be purchased from a violin maker or music shop. Peg chalk solves the
opposite problem and prevents slippage. Pegs can be prevented from sliding out
when new violin strings are put on: guide the string so that it lies very
close to the edge of the peg box as you wind it.
About the bridge
This carved, wooden support holds the strings at the correct height and
distance from each other and transmits the sound energy from the strings to
the body of the instrument. Since the bridge is fragile and not glued or fixed
to the table in any way, it is necessary to prevent impact to this sensitive
area and to ensure the bridge remains straight and be upright. Even with
normal use and regular tuning, a bridge will gradually lean forward or back in
the direction of the pegs or fine-tuners. If the bridge is left in this
position it will eventually warp under string tension. A bridge that is
slightly warped can be straightened at your violin shop but a severely warped
bridge will need replacement. To extend the life of a bridge, regularly
inspect its position and straighten it when necessary. To do this, one must
grip the bridge firmly with both hands and carefully ease it back into an
upright position.
About the string
Replace your strings regularly to ensure your instrument always plays and
sounds to its full potential. Strings gradually lose their warmth and
brilliance even if an instrument is not played frequently. When changing
strings, always replace them one at a time and make sure your bridge does not
begin to lean forward or backwards. To wind on a new string, maintain some
tension on the string at all times. Overlap the string once before you
continue to wrap it around the peg. Always take care to wind the string close
to the pegbox on the same side as the peg you are adjusting. A gentle fit
against the wall of the pegbox will prevent most pegs from slipping and
strings from unwinding.
Care the bow
The violin bow on a daily basis is to tighten the bow hair and then run the
rosin up and down the hair. Never tighten the bow hair too much and always
loosen the bow hair after playing is very important to keep the bow in a good
playing condition. The bow stick should also be wiped clean with a soft cloth
after each use to remove rosin dust. A soft cloth of microfiber or another
material reliably removes the freshly formed dust whilst also polishing the
surface of the stick somewhat. Do not pull such hairs out of the tip or frog;
instead, just use a sharp knife or very sharp pair of scissors to cut the hair
as short as possible and get the broken hair off the bow. The violin bow hairs
are secured at either end, and the mounting becomes loose if individual
strands of hair are ripped out.
Other Instructions
- While using new strings, as the tensile changes, the sound may be unstable, such as the tone decreases, and sounds decentralized, keeping the string tension and playing, which will trend to normal and stable after being adapted for one week.
- Please play more your own violin, that will be helpful for the vibration of the violin plate, and it will make sound quality turn better with the increase of playing times.
- The violin sunspots could fall during great fluctuations of humidity, the top and back swell when it is warm and humid, and the sunspots simply becomes too loose and falls, and please take the instrument to the repair store.
- If there is any other question or difficulty during the use, please contact Eastar, and we are pleased to answer your questions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>