Cylinda FK250C Recirculating Hood Popular User Manual
- June 5, 2024
- Cylinda
Table of Contents
USER MANUAL
RECIRCULATING HOOD POPULAR
FK250C, FK260C, FK270C
SAFETY INSTRUCTIONS
Please read this installation and user guide carefully before instal- ling and
using the product, paying special attention to the safety instructions.
Keep the instructions for reference or for the next owner. Disconnect the
product from the power supply prior to cleaning or maintenance.
- The diversion of exhaust air must be carried out in accordance with instructions issued by the appropriate authority.
- Exhaust air must not be directed into flues that are used for fumes from items such as gas, wood or oil-burning stoves or fireplaces.
- The distance between the sto- ve and the product must be at least 42 cm. For gas hob, the distance should be increased to 65 cm. Adjust accordingly if the stove manufacturer recommends a higher mounting height.
- For safety reasons, the installation and replacement of cab- les or other types of connectors should only be carried out by a qualified professional.
- You must not flambé food un- derneath the product.
- If the product is to be used at the same time as products that use energy sources other than electricity, i.e., gas hobs, gas, wood or oil-burning stoves or fireplaces, etc, the room must have an adequate supply of air.
- The product may be used by children from 8 years of age and persons with mental, sensory or physical impairment, or a lack of experience and knowledge, provided they are given information about how the product is to be used.
- Children should not be allowed to play with the product. Children must not undertake cleaning or maintenance of the product unsupervised.
- Accessible parts of the product may become hot when food is being prepared.
- A fire is more likely to spread if the product is not cleaned as frequently as indicated.
Attention!
The developer or proprietor is responsible for ensuring installation is
carried out correctly and complies with the applicable building regulations.
INSTRUCTIONS FOR USE
GENERAL INFORMATION
The product features LED lighting (6.5 W), aluminium filters, an AC motor and
the Easy Clean system.
FUNCTIONS
A. Fan speeds.
B. Lighting.
It is a good idea to turn on the fan before starting to cook, as this prevents
cooking smells spreading into the room. Adjust the speed of the fan depending
on the type of food you are preparing. If possible, allow the fan to run at a
low speed for a few minutes after you’ve finished cooking. You may also wish
to run the fan on the low setting when the oven is in use or after using the
dishwasher.
CARE AND MAINTENANCE
Cleaning the filter
The cooker hood should be cleaned with a damp cloth and washing-up liquid.
With normal usage, the filters must be cleaned at least every other month.
Clean more often after intensive use.
Remove the grease filter by opening the snap retainer, Fig. 2.
Handle the filter carefully, taking care not to bend it.
Soak the filter in a solution of warm water and washing-up liquid. The filter
can also be washed in a dishwasher.
Refit the grease filter after cleaning, making sure it snaps firmly into
place.
Cleaning other parts
The interior of the cooker hood and removable parts should be cleaned at least
twice a year.
Remove the bottom plate by pushing the snap retainers in the direction of the arrows.Fig. 3
Release the blower by bending the snap retainer outwards in the direction of the arrow (1) and pushing the blower away from you and down (2),Fig. 4.
Release the impeller by pulling in the direction of the arrow, Fig. 5
Clean the bottom plate, blower and impeller using warm water and washing-up
liquid. The blower and impeller can also be washed in a dishwasher. After
washing and drying, assemble the parts in reverse order.
Refit the impeller. Make sure that it is level in the groove
on the motor.
Refit the blower by inserting the supports in the rear of the hood (1). Bend up the blower (2).Fig. 7
Make sure all the snap retainers fit onto the cooker hood lugs. Twist the blower (1) into the lugs (2). Press the blower’s snap retainer back into the lug (3).Fig. 8
Attention!
Check that the parts snap firmly into place.
CHANGING THE CARBON FILTER
The carbon filter lasts for one to two years, depending on the household’s
cooking habits.
Push in the snap retainers on both sides of the hood (1) and
lift off the front (2). Then pull out and lift off the filter retainer (3),
Fig. 9.
Undo the filter locks and replace the carbon filter mat,
Fig. 10.
Refit filter locks, Fig. 11, filter retainer and front in
reverse order.
Attention!
Check that the filter retainer is positioned so that it covers the ventilation
opening on the cooker hood (1). Slide in the front so that it snaps into place
on both sides (2) and then gently press the top of the front so it also snaps
into place in the correct position (3), Fig. 12
SERVICE AND WARRANTY
TROUBLESHOOTING
Check that the fuse is intact. Go through all the functions to check what is
not working. Start by disconnecting the product from the power supply and
switching it on again.
Check that the connector is not bent or twisted at the connection point.
SERVICING
Before contacting servicing, check the pro- duct label and note down the FUN
number, S/N number and manufacturing date of the product.
The product label is located on the left side, underneath the filter/bottom
plate.
Contakt Cylinda Service
tel. +46 0771-25 25 00 or visit:
www.cylinda.se/service
They can help you fix the problem or refer you to the nearest service agent
for fast and effective service.
The product is covered by the relevant APPLiA provisions.
ENVIRONMENTAL INFORMATION
The main raw materials used in the product are:
- Metals: stainless sheet metal, galvanised sheet metal, zinc, aluminium
- Plastics: polypropylene, polyamide, polycarbonate, polybutylene terephthalate (PBT)
- Glass
All components comply with the RoHS Directive.
PACKAGING AND PRODUCT RECYCLING
The packaging should be deposited at your nearest recycling point.
The symbol means that the product must not be treated as household waste. It should instead be taken to a collection point for the recycling of elec- trical and electronic components. By ensuring that the product is dealt with in the correct manner, you are helping to prevent the adverse environmental and health effects that could arise if the product was disposed of as regular waste. For further information on recycling, contact your local authority or waste disposal service, or the store where you purchased your product.
ECO–DESIGN DIRECTIVE
The product has been tested in accordance with and meets the ecodesign
requirements of European Regulation 66/2014.
ELECTRICAL INSTALLATION
Electrical connection for 230 V~ earthed.
The product is supplied with a cable and earthed plug for connection to an
earthed socket. The socket should be accessible after installation is
complete. The junction box or wall socket must be accessible after
installation is complete. If the connector is damaged, it must be replaced
with an equivalent special cable from the manufacturer or their service agent.
INSTALLATION
Service
Nationwide service in Sweden
Visit www.cylinda.se
Call 0771-25 25 00
Declare
Model code
Serial number
Purchase date
Problem description
Name and address
Phone number
Contact us
www.cylinda.se
Elektroskandia Sverige A8, Cylinda, 191 83 Sollentua
991.0643.856/D000000007556/180433/2021-03-08 (38294)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>