Search

Using WebBrowser (cont.)

Monitor information window

This page indicates the projector status. To access this page from other pages, click [Status] in the main menu (at the left of the window).

Projector status
On this window, click the [Projector status] tab.

Network status
On this window, click the [Network status] tab.

The monitor information is refreshed at fixed intervals, but the current exact information can be checked by clicking [View] [Refresh].
If [SELF TEST Error (Detail)] appears on the Monitor information window, click it to view the error details.

If [FAILED] appears
Item MAIN CPU BUS FAN INPUT AIR TEMPERATURE
OUTPUT AIR TEMPERATURE LAMP REMAIN TIME LAMP STATUS
INPUT AIR TEMP.SENSOR OUTPUT AIR TEMP.SENSOR BATTERY AIR FILTER

Description There is a problem with a microcontroller circuit. Contact your dealer. There is a problem with the fan or fan drive circuit. Contact your dealer. Input air temperature is high. The projector is likely being used in a high temperature environment such as near heating equipment. Temperature surrounding the lamp is high. The exhaust vent is likely blocked. The lamp has been used for longer than its rated useful life, and it is time to replace it. The lamp could not be lit. Allow the bulb of the light source to cool, and then turn on the projector. There is a problem with the air intake temperature sensor. Contact your dealer. There is a problem with the exhaust temperature sensor. Contact your dealer. The battery must be replaced. Contact your dealer. The remaining filter gets low. For further detail, see the Basic Manual.

11

Search

Using WebBrowser (cont.)

Projector control window

You can make various projector settings. If you migrate from other page, click [Projector control] in the main menu (at the left of the window).

Basic control window
On this window, click the [Basic control] tab.

Advanced control window
On this window, click the [Advanced control] tab.

Connection with the projector may not be possible immediately after the power is turned on. In this case wait a bit and then make the connection again.
Detailed set up window
Network config
You can make detailed wired LAN settings.
1 Click [Detailed set up] [Network config] in the menu.
2 Confirm the notes that appear on the screen and click [Next]. The settings window appears, showing the current settings. · To change the LAN settings, click [Change]. · To return to the previous window, click [Back].

12

Search

Using WebBrowser (cont.)
3 Complete the detailed settings and click [Next]. When [Next] is clicked, the next page appears, enabling you to complete the detailed settings as desired. After all required items have been entered, a confirmation window appears.
4 Click [Submit]. The settings will be registered.

If you have changed the LAN settings that are currently in use, the connection may break off.

Adjust clock

Click [Detailed set up] [Adjust clock] in the menu.

Time zone : Select the time zone and click [Set time zone].

Time :

Enter the current date and time in [Date] and [Time],

and then click [Set date and time].

13

Search

Using WebBrowser (cont.)

E-mail set up

You can specify two email recipients. Click [Detailed set up] [E-mail set up] in the menu.

· [MAIL SERVER]

ENABLE :

Enable or disable email transmission.

SMTP SERVER NAME : Enter the SMTP server name.

· [MAIL OPTION] MAIL FROM :
MEMO :

Enter the sender’s email address. Enter a description of the sender.

· [TEMPERATURE WARNING SET UP]

MINIMUM TIME :

Enter the interval for sending email.

INPUT AIR TEMPERATURE : Select the temperature of the intake sensor

at which to send a warning message.

· [E-MAIL ADDRESS]

E-MAIL ADDRESS : Enter the email addresses of the recipients.

MAIL CONTENTS :

Change the type of message as desired.

When sending messages to mobile phones, select “SIMPLE”.

ERROR :

Select ON to send email when errors occur.

LAMP RUNTIME :

Select ON to send email when “at REMAIN” is reached.

INPUT AIR TEMPERATURE : Select ON to send email when the temperature set in [TEMPERATURE WARNING SET UP] is

exceeded.

PERIODIC REPORT : Send a message with the projector status at the selected date and time.

When [submit] is clicked, the settings are applied.

Consult your system administrator on MAIL SERVER and E-MAIL ADDRESS settings.

Ping test
You can confirm if a network connection is established with Mail server, POP server, DNS server or the like. Click [Detailed set up] [Ping test] in the menu.
Input IP address : Enter the IP address of the server you want to test, and then click [Submit].
If succeeded in connection, the following display appears.

If failed in connection, the following display appears.

14

Search

Using WebBrowser (cont.)

Example of email message sent
If [NORMAL] is selected under [MAIL CONTENTS]

If you have completed the email settings

If an error occurs

If [SIMPLE] is selected under [MAIL CONTENTS]

If you have completed the email settings

If an error occurs

15

Search

Using WebBrowser (cont.)

Authentication set up

Click [Detailed set up] [Authentication set up] in the menu.

Auth :

Change the authentication method as desired.

SMTP Auth :

For SMTP authentication, change the authentication method to use, as desired.

Pop Server name : Enter the POP server name.

User name :

Enter the user name for the SMTP or POP server.

Password :

Enter the password for the SMTP or POP server.

SMTP server port : Enter the SMTP server port number.

POP server port : Enter the POP server port number.

When [submit] is clicked, the settings are applied.

Command port set up
Click [Detailed set up] [Command port set up] in the menu.
COMMAND PORT : Specify a port number to be used for command control and click [Set port].

Change password window
Password settings
Click [Change password] in the main menu. Set a password for accessing the web control window. Enter the previous password and the new password. Enter the new password in [Retype] and click [OK].
· You can enter a password up to 16 characters (upper case/lower case)
and symbols.
· When log in as administrator, you can reset the User name and the
Password (forced change) that logged in with administrator/user authority.

Switching Languages

Switch the language of the web control window.

Click [English] / [

] in the main menu.

16

Search

Using PJLink protocol
The projector’s network functions conform to PJLink Class 1 standards, enabling the following operations from a computer using the PJLink protocol.
· Setting the projector · Querying the projector status
To use PJLink protocol, turn [ON] the [NETWORK CONTROL] in the NETWORK menu for the projector. (See page 7)

Applicable commands
The following commands are used to control the projector with the PJLink protocol.

Command

Control details

POWR

Power control

POWR ?
INPT INPT ? AVMT AVMT ?

Power status query
Input switching Input switching query AV mute control AV mute status query

ERST ?

Error status query

LAMP ? INST ? NAME ?

Lamp status query Input switching list query Projector name query

Notes

Parameters 0 = Standby 1 = On

Parameters 0 = Standby 2 = Cooling down

1 = On 3 = Warming up

Parameters 11 = COMPUTER1 21 = VIDEO

12 = COMPUTER2 22 = S-VIDEO

Parameters 30 = AV mute off 31 = AV mute on

Parameters

1st byte : Indicates fan errors; a number from 0 to 2

2nd byte : Indicates lamp errors; a number from 0 to 2

3rd byte : Indicates temperature errors; a number from 0 to 2

4th byte : Fixed at 0

5th byte : Fixed at 0

6th byte : Indicates other errors; a number from 0 to 2

Numbers from 0 to 2 indicate the following

0 = No error detected

1 = Warning

2 = Error

Parameters 1st number (1­5 digits) : Cumulative hours of lamp use 2nd number : 0 = lamp off ; 1 = lamp lit

The following values are returned in this parameter “11 12 21 22”

Returns the name set in “HOSTNAME ” in “NETWORK” The “HOSTNAME” is the projector name set in the projector itself.

INF1 ?

Manufacturer name query

Returns “Panasonic”

INF2 ?

Model name query

Answers the name of the projector in use.

INFO ?

Query for other information Returns the version number or similar identification

CLSS ?

Class information query

Returns “1”

PJLink security authentication
The password used for PJLink is same as the one you set in the WEB control. Configure this without specifying the password for the WEB control, if you use it without authentication. For details on PJLink specifications, refer to the Japan Business Machine and Information System Industries Association website. The URL is http://pjlink.jbmia.or.jp/english/

17

Search

Glossary

LAN

Item

DHCP

IP address

Subnetmask

Default Gateway

MAC address

Descriptions
Abbreviation for Local Area Network. This is a network with a relatively narrow range such as inside a company.
Abbreviation for Dynamic Host Configuration Protocol. This function automatically assigns IP addresses to the connected equipment. If a device with the DHCP server function is present within a LAN, it automatically assigns IP addresses to the connected equipment.
Internet Protocol (IP) is a protocol for distributing data, and the address corresponding to the data distribution destination is called the IP address. The same IP address cannot be used within the same LAN.
This limits the range of the IP addresses assigned to computers in order to divide the network into a number of sections during TCP/IP connection. The value used to divide the network at this time is called the subnetmask.
The devices that are used for different network standards from yours. Default Gateway enables a connection with other network, by adjusting bilateral differences such as communication protocols. If no gateway is specified for the IP address of access destination, data will be sent to the host set as the default gateway.
Each network adapter has its own ID No. A discrete ID No. is assigned to each and every network adapter around the world. These IDs are used to exchange data between adapters. These IDs are a combination of a discrete number managed and assigned by the IEEE to each individual manufacturer and a unique number assigned to each individual adapter by the manufacturer.

Page 4 6 6 6 6
8

Trademarks
· Microsoft ® and its logo are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or
other countries.
· PJLink is a pending trademark in Japan, the United States and other countries and regions. · Other company names, product names or other names noted in this manual are trademarks or registered trademarks of the
respective companies. Note that ® and TM marks are not indicated in the text of this manual.
Notes:
· Unauthorized use or reproduction of part or all of this manual is strictly prohibited. · Panasonic cannot be held liable for any effects resulting from the use of this manual. · Panasonic reserves the right to revise this manual contents without notice.

18

Search

Web Site : http://panasonic.net/avc/projector/ © Panasonic Corporation 2011

Search

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>