SKYWORTH SEP001 Bluetooth Headset User Manual
- June 17, 2024
- SKYWORTH
Table of Contents
SKYWORTH SEP001 Bluetooth Headset User Manual
Packing List
Specifications
Product Overview
Caution
Before the first use, please tec1r off the protective film on the earbuds. Then put the earbuds into the use to fully charge.
Charge by Type-C cable
Place earphone Into charging case properly, then use the included Type-C charging cable to connect the charging case, and plug the other erred into power supply with a adapter(not included ,it will start charging. After full charge, the LED indicator of charging case will be off.
Note:
⚠ If the power of the earphones is lower them 10% voltage is lower than 3.55V).You will hear the voice prompt of ‘Battery low’ .If there is on charging and the voltage of the earphones is lower than 3.2V,it will automatically shut down.
⚠ If the earbuds don’t charge or even can’t turn on because of oxidized magnet connector, you can handle ties problem by using alcohol rag to clean tie magnet connector on earbuds and charging case.
Turn On/Off
Turn on
open t he case. the earphones will turn on a automatically. Or press and hold
the left & right earphones for 3 seconds to turn on.
Indicator Light: Red and blue lights flash alternately.
Turn off
After putting the earphones into the charging case and closing it, the
earphones will automatically turn off and start charging.
Or press and hold the earphones for 5 seconds to turn them off Indicator
Light: The red Light flashes 2 times and t hen turns off
Note: Earphones will automatically turn off after10 minutes of no connection .
Bluetooth Connection
First Time Pairing
Step 1 -Take twin earphones out from charging case, they will automatically
power on and enter pairing mode.
Indicator light: the main earphone- the red and blue light flashes
alternately, the auxiliary earphone – the light is off
Step 2 – Turn on the bluetooth function of the device, •sKYWORTH-SEP001• wc appear on the bluetooth search page, click .SKYWORTH· SEP001. to pair, and the LED light of the earphones will turn off after the pairing is successful.
Bluetooth Connection
For second Time use
If the earphones have already connected with your device, and the bluetooth
setting of this device is on. in the second time using, when you take out the
earphones from the charging case, they will connect with your device
automatically.
Pair with other Device
SEP001 earphones bluetooth has memory function, it usuaUy auto connects with
the last paired device.
Therefore, if you want to pair them with other devices, you should prevent the
•sKYWORTH-SEP001• from connecting with the last paired device.
It can be prevented by the following methods.
- Turn off the bluetooth of the last paired device,
- Turn on the bluetooth of the last paired device, and delete “SKYWORTH-SEP001. from this device.
- Quickly tap the earphones s times to clear the earphones history.
Multi Function Operations
Reset Operation
You might need to reset the earbuds if you experience ;1nyconnectivtty problems or functions Issues.
- Touch Five elide; Multi-Function Button on either earphone, talc indicator light-red light flashes 2 times and then goes old. This confirms that the ruleset was successful .1nd your Barbican be connected normally.
Maintenance
After a period of use, the charging metal contacts of the earphones may be
polluted by sweat and dirt, causing the earphones to fail to turn on or
charge; and the protective grille of both earphones may accumulate earwax and
dust, resulting in muffled volume.
If you experience issues with the earphones not charging, use a clean, soft
cloth to gently wipe the charging metal contacts to
remove sweat and dirt.
If you experience earphone sound muffled, not as loud as when you first started using it. Use a soft brush or cotton swab ta gently remove earwax and dust from the grille. Avoid using sharp objects to avoid damage.
Your earbuds are sweat and water-resistant, but the charging port and charging case are not waterproof, so don’t wash it with water.
FAQ
Q: Why these earphones can not pair with my mobile phones?
A:
-
Please make sure the earphones ,3re full charged and power on.
-
Please make sure the bluetooth of your phone is turn on.
-
Remove the protective film from the bottom of the earphones.
-
Please make sure that this is the first time the earphones is connected. If the earphones has been connected to your other
devices before connecting to the phone, please turn off the bluetooth of other devices first. -
If above 4 points have no problem, please put earphones into the cc1se again and dose the case, hold on for 1 min, then open the charging case and reconnect earphones with your phone.
Q: Why does the music cut in or cut out.
A: First, please do not let the distance between these earphone sand your
phone be more than 700 feet(without obstacle). lf the
distance is less than 1 DO feet, please take steps as follow:
- Put earphones back: into case and close it, find “SKYVIIORTH-SEP001” in the bluetooth list and click “Forget the device~ on your phone.
- After 10s later, open the case and reconnect these earphones with your phone.
FCC Statement
This device complies with pan 15 of the FCC Rules. Operation is subject to the following two conditions.(1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Changes or modification’s not expressly 11pproved by the party responsible for compliance could void The user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
doss B digital device, pursuant to pan 15 of the FCC Rules. These limits are
desi9ned to provide reasonable protection against harmful interference in a
residential installation.
This equipment9en~ates, uses and can radiate radio frequency unit and, if not
installed and used in accordance with the instructions. may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does Curse harmful interference to r11dio or television reaction, witch can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– connect the equipment into an outlet on a circuit different from that to
witch the receiver i5 connected
– Consult the dealer or an experienced radio/TV technician for help.
Important Note:
Radiation Exposure Statement
This device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.