SKYWORTH T8811C1 Wireless Wi-Fi USB Module Instruction Manual

: June 1, 2024
: SKYWORTH

Table of Contents

SKYWORTH T8811C1 Wireless Wi-Fi USB Module Instruction Manual
Operation Instruction
List of applicable FCC Rules:
Summarize the specific operational use conditions
Limited module procedures
Trace antenna designs
RF Exposure compliance statement
Antenna Change Notice to Host manufacturer
Labelling Instruction for Host Product Integrator
Information on test modes and additional testing requirements
FCC other Parts, Part 15B Compliance Requirements for Host product
ISED compliance statement
ISED Radiation Exposure statement
End Device Labelling
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SKYWORTH T8811C1 Wireless Wi-Fi USB Module Instruction Manual

Operation Instruction

peripheral products.

users browse and download data flow, security and stability.

Android.

Used in TV production operation is as follows:

Turn on the TV, switch to the “home page” interface;
Select “Settings” “OK” to enter;
Select “network setup” “OK” to enter;
Choose the “wireless network”, “OK” to enter;
According to the needs, select “auto search”, “manual connection”, etc. Press the “OK” to enter;
Choose their own after the AP name “OK” to enter, Enter the password;

Television system has the memory function, for the first time to use should be according to the above steps, later need not operation, boot automatically connected. If need to change the AP or change the mode of connection, need according to the above steps again;

FCC regulatory compliance statement

15.19 Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

15.21 Information to user

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

List of applicable FCC Rules:

47 CFR Part 15, Subpart C 15.247
47 CFR Part 15, Subpart E 15.407
47 CFR Part 2.1091

Summarize the specific operational use conditions

This module can be used in IOT devices, the input voltage to the module is nominally 3.3V.

Limited module procedures

This module is not a limited module.

Trace antenna designs

The antenna is not a trace antenna.

RF Exposure compliance statement

This Module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Antenna Change Notice to Host manufacturer

If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application.

15.19 Labelling requirements shall be complied on end user device.

Labelling rules for special device, please refer to §2.925, § 15.19 (a)(5) and relevant KDB publications. For E-label, pleasrefer to §2.935

Labelling Instruction for Host Product Integrator

Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: 2ANM3T8811C1” any similar wording that expresses the same meaning may be used.

Information on test modes and additional testing requirements

The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module.
The module is limited to installation in mobile application, a separate approval is required for all other operating configurations, including portable configurations with respect to §2.1093 and difference antenna configurations.
Test software access to different test modes: Bluetooth test 3 (V2.6)
Testing item, Frequencies, Transmit Power, Modulation Type can be selected on the test script instructions.

FCC other Parts, Part 15B Compliance Requirements for Host product

manufacturer
This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements.
Please note that For a Class B or Class A digital device or peripheral, the instructions furnished the user manual of the end-user product shall include statement set out in §15.105 Information to the user or such similar statement and place it in a prominent location in the text of host product manual. Original texts as following:
For Class B
For Class A

ISED compliance statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause
This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

ISED Radiation Exposure statement

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux radiations IC CNR-102 établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.

End Device Labelling

Please notice that if the IC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 23165-T8811C1” any similar wording that expresses the same meaning may be used.

L’étiquette d’homologation d’un module d’Innovation, Sciences et Développement économique Canada devra être posée sur le produit hôte à un endroit bien en vue, en tout temps. En l’absence d’étiquette, le produit hôte doit porter une étiquette sur laquelle figure le numéro d’homologation du module d’Innovation, Sciences et Développement économique Canada, précédé du mot « contient », ou d’une formulation similaire allant dans le même sens et qui va comme suit :Contient IC :

23165-T8811C1” est le numéro d’homologation du module5G Wi-Fi Use Notice

The user manual for LE-LAN devices shall contain instructions related to the restrictions mentioned in the above sections, namely that:

the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour uneutilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
pour les dispositifs à antenne (s) détachable (s), le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5470-5725 MHz doit se conformer à la limite de p.i.r.e.;
pour les dispositifs à antenne (s) détachable (s), le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissancesont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

This radio transmitter [IC: 23165-T8811C1] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.a list of all antenna types

Le présent émetteur radio [IC: 23165-T8811C1] a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d’antenne énumérés ci‑dessous et ayant un gain admissible maximal. Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l’exploitation de l’émetteur.