FELLOWES F8949401 Levado Height Adjustable Desk Base Instruction Manual

FELLOWES F8949401 Levado Height Adjustable Desk Base

SAFETY INSTRUCTIONS/WARNING

WARNING: IMPORTANT SAFETY INSTRUCTIONS – Read Before Using!

• CAUTION: Lift hazard! Two people are required to move desk. Serious injury may occur.
• DO NOT EXCEED MAXIMUM STATED WEIGHT CAPACTY. SERIOUS INJURY OR PROPERIY DAMAGE MAY OCCUR.
• Do Not operate table if any part is damaged or defective. Do Not place obstades in the desk’s path.
• Do Not place objects under the desk that are taller thon 610mm (24′) Make sure the desk has proper durance on all sides (at least 25mm (1 )) to allsurrounding walls and objects. Do Not sit or stand on the desk.
• Do Not disassemble the legs, control box or controller
• Serious injury may ocur.
• Ensure all cable lengths are long enough to accommodate all changes in height and follow cord routing instructions in this manual. Failure to tollow these instructions may result in equipment damage or personal nury.
• Keep liquids away from all electrical components. Only clean electical components with a dry cloth. For indoor use only. Keep power cable away from sources of heat.
• Unplug desk before moving or servicing. Remove all equipment and accessories from the desk before moving. Keep children away from moving parts and underneath the desk.

Maximum Weight Including Table Top

Accommodates table tops with the following dimensions:

• Width: 1187-1816mm
• Depth: 700-800mm
• Thickness: 19-31.75mm

PARTS PROVIDED

• A Base x
• B Clamp x2 A Handset x1
• C Handset x1
• D Power cable xl Cable Tray xl
• E Cable Tray x1
• F Cable Management x4
• G Smm Allen Key x1
• H M6 Phillips round head strew xl4
• M3 Phillips round head screws x2
• JClamp Covers x2

Additional Tools Required

• Phillips Screw Driver

INSTALL OPTION 1 – CLAMPS

STEP 1
Unboxing

• Open box from the fop.

• Ensure levers on base are in the upright position.
  WARNING: Pinch Point! Keep hands

• Fold out legs until they click. and objects dear when lilting leg.

• Lock legs into place by pushing down on levers.

• Optional: If legs need to be folded, ensure lever is in the upright position and power is unplugged. Pall out pin and carefully guide legs to folded position.

• Using two people, fit the bused uprights.

• The base arrives adjusted for 1600mm (63″) wide tables. If your table is not 1600mm (63″) wide you will need to adjust the base width 1187- 1816mm (47″- 715). See step 18, otherwise move on to step 2.

STEP 18-Only required if table is not 1600mm (63″) wide
Adjust the cross channels to their final lengths

• Using two people, place table face down on a soft, dean surface and place base on table.
• Use the Smm Allen key to loosen the (8) set screws on the inward side of the Cross channels.
• Expand or contract the cross channels until fuss with both ends of the desk. Free cables as necessary to allow the frame to adjust. Once properly adjusted, use the Smm Allen key to re-tighten the set strews (8 total).
• Using two people, ip the base only upright.

STEP 2

• Adjust the position of the frame before attaching it to the table
• Using two people, place the table top on the base.
• Check that the table top supports on each side are flush to both ends of the desktop and align to the predrilled holes on the desktop.
• The rear cross channel will be 240mm (9.5″) for 800mm (31.5″) Depth Tops from the rear of the table.

STEP 3

• Clamping base to table Slide clamps on each side of the table.
• On each damp, tighten the (2) thumb screws until each click.

INSTALL OPTION 2- HARDWARE

STEP 1

• Preparing for installation using two people Place table face down on a soft, dean surface.

• Ensure levers on base are in the upright position.

• Fold out legs until they click,
  WARNING: Pinch Point! Keep hands and objects dear when lifting legs.

• Lock legs into place by pushing down on lever.

• Optional: IF legs need to be folded, ensure lever is in upright position and power is unplugged. Pull out pin and carefully guide legs to folded position.

• Lilt bees out of box and place on table.

The base arrives adjusted for 1600mm (63″) wide tables. Ii your table is not 1600mm (63) wide you will need to adjust the base width 1187-1816mm (47″-715″). See step 18, otherwise move on to step 2.

STEP 1B-Only required if table is not 1600mm (63″) wide
Adjust the cross channels to their final length

• Use the Smm Allen key to loosens the (8) set screws on the inward side of the cross channels.
• Expand or contract the cross channels until flush with both ends of the desk. Free cables so necessary follow the frame to adjust.
• Ensure proper alignment to predrilled holes on the desktop.
• Once properly adjusted, use the Smm Allen key to re-lighten the set screws (8 total).

STEP 2
Adjust he position of the frame before attaching it to the table.

• Check that the top supports on each side are fuss to both ends of the desktop and align to the predrilled holes on the desktop.
• The rear cross channel will be 240mm (9.5″) for 800mm (31.5″) Depth Tops from the rear of he table.

STEP 3

• Attach base to the table Use the M6 Philips round head screws (8 total required) and a Philips screwdriver.

• The sews fi through quires in the top of the supports., Ensure proper alignment with predrilled holes on the desktop.

• Using two people, flip the Bose and Table upright.

• Attach damp covers to each side. Start by plodding the smaller piece on the inside of the clamp bracket.

• Align the larger piece and apply pressure to secure.

ACCESSORY INSTALLATION

STEP 1

• Cable Management Partially drive (4) Philips Head screws into the pre-drilled holes located towards the back of the table.
• Hook the cable fray key slots onto the strews and slide the troy to lack it in place. (Note: the open end of the cable troy should force the back of the table.)
• Tighten the (4) Philips Head sauces to secure the cable tray.
• Use the additional provided cable management as needed.
• Cables must not interfere with table operation. Cables must not interfere with the user.

STEP 2

• Attach the handset using the included adhesive strip or using two M3 Phillips round head strews
• Position the handset on the left or right side of the table, according to user preference.
• Mount the handset flush to the front edge of the table. If using M3 attachment method, ensure handset is  up to pre-drilled holes on the desktop. Plug handsel into controller on base.
• Plug power cable into controller on base and into an power outlet.
  

STEP 3
Level Feet

• IF table feels unbalanced adjust the (4) leveling pads located on bottom of fet.
• Turn clockwise to lower and counter clockwise to raise.

OPERATING INSTRUCTIONS

INITIALISE THE SYSTEM
WARNING: Only light pressure required to operate handset. When lowering the table, apply light pressure to the center of the handset (shown below). Applying too much pressure, puling or pushing on the lower part of the handset may cause damage to the unit
IMPORTANT: The initialization process below must be completed before operating the table. Throughout the initialization operation, CAL s displayed and will remain until procedure is complete.
CAUTION: Ensure proper clearance. Make sure all objects are dear of the table LHL

• Lightly touch the center of the handset and M buttons simultaneously for 10-15 seconds.
• The legs il begin to move down at hold speed of normal operation. Continue to hold the buttons.
• The legs will move down to the lowest position, then rebound 2mm to 5mm (1/16′ to 3/16) and stop. Ihis can take between 10-45 seconds depending on the hickness of the toble top.
• Release both buttons at the same time.
• This completes the initialization procedure.
• IF initialization is started and not finished, the table will not operate. You must finish the initialization process.

GENERAL OPERATION

Move the table up or down by lightly holding your finger on the top or back of the handset until the work surtace reaches the desired height. Ihe table will continue to move up or down until you release the button or unfilm the maximum or minimum height is reached.

MEMORY STOP POSITIONS

There are two groups of memory settings, each with two height settings. To toggle between the two users momentarily press the M button and display will read Ul or U2. Up to tour memory stop posiions can be used to save specific heights of the work sUurtace. To set a specific position: Raise or lower the table to the position you want for save. Light touch the M button for two seconds, the LED display will blink. This means it has stored the location. lo clear storage settings, lightly touch the M button for 8 seconds until CLR displays.

CHANGING THE HEIGHT DISPLAY UNITS

This function allows you to toggle the display units from inches to centimeters. Lightly touch and hold up and down at same time for 10 seconds.

RESET THE SYSTEM TO FACTORY SETTINGS

To reset the handset to factory settings follow the same instructions as ‘initialize the System. In case of error message or in the event of a power outage please reset the system.

FELLOWES LEVADOTM HEIGHT ADJUSTABLE DESK BASE LIMITED WARRANTY

Fees, Inc. (the “Company”) warrants the Leva do M Height Adjustable Desk Bose (“Product”) to be free from defects in material and workmanship for the time period as set forth below. The studied frame for a period fen (15) years rom the dote of original purchase of the product. lleledrial components for a period of seven ) yenrs rom the dent of original purchase of the product. This warranty poleis only to the initial purchaser and does not cover dlainms resulting from misuse, failure to follow intrusions on installation and use, neglect, use of unauthorized attachments, commercial use, Use on a current or voltage other than specified on the product, or unauthorized service during the warranty period on conditions otherwise covered by warranty. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPUIED WARANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS EXPRESSIY LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. UNLESS REQUIRED BY APPLICABLE LAW, THE CUSTOMER’S EXCLUSIVE REMEDY FOR BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY OR OF ANY OTHER OBLIGATION ARISING BY OPERATION OF LAW OR OTHERWISE SHALL BE LIMIIED AS SPECIHIED HEREIN TO REPAIR, REPLACEMERNT OR A REFUND 0F THE PURCHASE PRICE, AT THE COMPANY’S SOLE OPTION. UNDER NO CIRCUMSTANCE WILL THE COMPANY, ITS AFFILIATES, SUBSIDIARIES, RELATED ENTITIES, RESELLERS OR THEIR RESPECTIVE OFFICERS, DIRECTORS OR EMPLOYEES OR THOSE PERSONS FOR WHOM THEY ARE BY LAW RESPONSIBLE, BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUSTAINED IN CONNECTION WITH THE PRODUCI. THE COMPANY AND THESE OTHER PARIES DO NOT ASSUME OR AUTHORIZE ANY REPRESENTATNVE OR OTHER PERSON TO ASSUME FOR ANY OF THEM ANY OBLIGATION OR LIABILITY OTHER THAN AS IS EXPRESLY SET FORTH HEREIN. The durafion, terms and conditions of this warranty are valid worldwide, except where different limitations, restrictions or conditions may be required by local low. Australia Residents Unly: Our goods come with guarantees that cannot be excluded under the Australian Consumer Low. You are entitled to a replacement or refund tor a major failure and tor compensation for any other reasonably foreseeable loss or damage. You are also entered to have the goods repaired or repiloted it the goods fail for be of acceptable quality and the failure does not amount for a major failure. The benefits under mellows Warranty are in addition to other rights and remedies under a law in relation to the product.

This product is densified as Electrical and Electronic Equipment. Should the time come for you to dispose of this product please ensure that it is not mixed with general household waste. For proper fragment, recovery and recycmg, please Loke this produced for designated calichon point. Please comfort your local authority tor further details of your nearest designated collodion point.

CUSTOMER SERVICE & SUPPORT

www.fellowes.com
Europe Freephone: 00800-1810-1810
Benelux: +31-(0)-13-458-0580
Deutschland: +49 (0)511 545489-0
France: +33 (0) 1 78 64 91 00
Italia: +39-071-730041
Polska: +48 (22) 205-21-10
España/Portugal: +34-91-748-05-01
United Kingdom: +44 (0) 1302 836836
Australia: 1800 33 11 77

Declaration of Conformity

Fellowes, Inc.
Unit 2 Ontario Drive, New Rossington, Doncaster, DN11 0BF, England declares that the product model Levado™ Height Adjustable Desk Base conforms with the requirements of the Low Voltage Directive (2014/35/EU), the Electromagnetic Compatibility Directive (2014/30/EU), the Restriction of Hazardous Substances Directive (2011/65/EU) and (2015/863/EU), the WEEE directive 2012/19/EU), the Eco Design Directive (2009/125/EC), and the below harmonized European EN Standards.

Mechanical Safety:
EN 527-1: 2011
EN 527-2: 2016
EN 1730: 2012

Electrical Safety:
EN 60335-1: 2017
EN 62233: 2008
EN 61558-1: 2009
EN 61558-2-16: 2013

Electrical Safety:
EN 60335-1: 2017
EN 62233: 2008
EN 61558-1: 2009
EN 61558-2-16: 2013

ErP:
EN 50563: 2011/A1: 2013

Year Affixed: 18
Itasca, Illinois, USA
August 1, 2018

1789 Norwood Avenue, Itasca, Illinois 60143 t 1-800-955-0959 t www.fellowes.com
© 2021 Fellowes, Inc. | Part #872472 Rev F

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>