GE AJES09DCA Room Air Conditioner Owner’s Manual

GE AJES09DCA Room Air Conditioner

Product Information

Specifications

• Model: AJCH 08, 10; AJCH 10, 12; AJCS 06; AJCS 08, 10; AJCS 09, 10, 12; AJES 09, 10, 12; AJEH 12; AJHS 08, 10
• Type: Chassis Only

Safety Information
Before using the product, please read and follow the safety precautions listed below:

• Use the air conditioner only for its intended purpose as described in the Owner’s Manual.
• Properly install the air conditioner according to the Installation Instructions.
• When unplugging the air conditioner, grip the plug firmly and pull straight out from the receptacle.
• Immediately repair or replace electric service cords that are frayed or damaged.
• Turn the mode control to OFF and unplug the air conditioner before making any repairs or cleaning.
• Do not store or use combustible materials, gasoline, or other flammable vapors or liquids near the appliance.

Operating Instructions

Air Direction
The air direction of the air conditioner can be adjusted. Refer to the controls section for more information.

Controls
The controls on the air conditioner allow you to adjust various settings. Follow the instructions below:

1. Turn the air conditioner on by pressing the power button.
2. Adjust the temperature using the temperature control buttons.
3. Select the desired fan speed using the fan switch.
4. Use the vent control to adjust the airflow direction.

Fan Switch
The fan switch on the air conditioner allows you to select the desired fan speed. Choose from low, medium, or high settings.

Temperature Limiting
The air conditioner has a temperature-limiting feature that allows you to set a maximum temperature. This feature can be useful to prevent the room from getting too cold.

Vent Control
The vent control on the air conditioner allows you to adjust the direction of the airflow. You can choose to direct the air upwards, downwards, or straight ahead.

Care and Cleaning

Air Filter
The air filter of the air conditioner should be cleaned regularly to ensure optimal performance. Follow these steps to clean the air filter:

1. Turn off the air conditioner and unplug it from the power source.
2. Locate the air filter behind the front grille.
3. Remove the air filter and gently wash it with warm water and mild detergent.
4. Allow the air filter to dry completely before reinstalling it.

Front Grille
The front grille of the air conditioner can be removed for cleaning. Follow these steps:

1. Turn off the air conditioner and unplug it from the power source.
2. Gently pull the front grille forward to remove it from the unit.
3. Clean the front grille with a soft cloth and mild detergent.
4. Once clean, reattach the front grille to the unit.

Grille and Case
The grille and case of the air conditioner can be cleaned using a soft cloth and mild detergent. Avoid using abrasive cleaners that may damage the surface.

Outdoor Coils
The outdoor coils of the air conditioner should be inspected and cleaned regularly. Follow these steps:

1. Turn off the air conditioner and unplug it from the power source.
2. Remove any debris or obstructions from the outdoor coils.
3. Clean the coils using a soft brush or vacuum cleaner.
4. Ensure that the coils are dry before turning on the air conditioner.

Installation
Please refer to the Installation Instructions provided with the product for detailed instructions on how to properly install the air conditioner.

Troubleshooting Tips
If you experience any issues with the air conditioner, please refer to the Troubleshooting Tips section in the Owner’s Manual for possible solutions. If the problem persists, contact our Consumer Support for further assistance.

FAQ

• Q: Where can I find the model and serial numbers of my air conditioner?
  A: The model and serial numbers can be found on a label located on the front of the base pan behind the front grille.

• Q: Can I use an extension cord with the air conditioner?
  A: It is not recommended to use an extension cord with the air conditioner. It is best to plug it directly into a wall outlet to ensure proper power supply.

• Q: How often should I clean the air filter?
  A: The air filter should be cleaned at least once every month or as needed, depending on the usage and air quality.

• Q: Can I adjust the direction of the airflow?
  A: Yes, the air conditioner has a vent control that allows you to adjust the direction of the airflow. You can choose to direct it upwards, downwards, or straight ahead.

• Q: What should I do if the air conditioner is not cooling properly?
  A: If the air conditioner is not cooling properly, first check if the air filter is clean and the vents are not blocked. Ensure that the temperature and fan settings are appropriate for your comfort. If the issue persists, refer to the Troubleshooting Tips section in the Owner’s Manual or contact our Consumer Support.

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.

WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

SAFETY PRECAUTIONS

• Use this appliance only for its intended purpose as described in this Owner’s Manual.

• This air conditioner must be properly installed in accordance with the Installation Instructions before it is used.

• Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the receptacle.

• Repair or replace immediately all electric service cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.

• Turn the mode control to OFF and unplug your air conditioner before making any repairs or cleaning.
  NOTE : We strongly recommend that any servicing be performed by a qualified individual.

• For your safety…do not store or use combustible materials, gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

• The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.
• Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
• Where a 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
• The air conditioner should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.
• This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.
• See the Installation Instructions, Electrical Requirements section for specific electrical connection requirements.

WARNING!
USE OF EXTENSION CORDS–115-Volt models only

• Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.
• However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed, 14 gauge, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 125 volts.

CAUTION:
DO NOT use an extension cord with any of the 230/208 volt models.

USE OF ADAPTER PLUGS –115-Volt models only

• Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.
• However, if you must use an adapter, where local codes permit, a temporary connection may be made to a properly grounded 2-prong wall outlet by use of a UL-listed adapter available at most local hardware stores.
• The larger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper polarity in the connection of the power cord.
• When disconnecting the power cord from the adapter, always hold the adapter in place with one hand while pulling the power cord plug with the other hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.
• If the adapter ground terminal breaks, DO NOT USE the air conditioner until a proper ground has been established.
• Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the cover screw is metal, and not insulated, and the wall outlet is grounded through the house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS

About the controls on the air conditioner.

Controls

1. Mode Control

   • HIGH COOL and LOW COOL provide cooling with different fan speeds.

   • HIGH HEAT and LOW HEAT provide heating with different fan speeds.

   • LOW FAN or HIGH FAN provides air circulation and filtering without cooling or heating.
     NOTE : If you move the switch from a cool or heat setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a cool or heat setting. A 3-minute delay is automatically provided on the Heat/Cool and Heat Pump models.

   • Cooling/Heating Descriptions

   • For Normal Cooling or Heating—Select

   • HIGH COOL or HIGH HEAT with the thermostat at mid point.

   • For Maximum Cooling—Select HIGH COOL with the thermostat at maximum cool.

   • For Maximum Heating—Select HIGH HEAT with the thermostat at maximum heat.

   • For Quieter & Nighttime Cooling—Select

   • LOW COOL with the thermostat at mid point.

2. Temp Control

   • The temp control is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same level of comfort. When you turn the knob to
   • COOLER (blue) the indoor air will become cooler. Turn the knob to  WARMER (red) and the indoor air will become warmer.
   • Heat Pump Models
   • When the outdoor temperature is lower than 25°F., heat is provided by the electric heater in the air conditioner instead of by the heat pump.
     NOTE : The electric resistance heater in the 115-volt heat pump model operates during defrost when the outdoor coil temperature is below 36°F. It is not
     intended to provide full heat capability.

Fan Switch
On Heat/Cool models, the fan switch lever is located in a hole through the control panel. To reach it, you need to remove the front grille. Use a small screwdriver to change the setting. Cool only models have a rocker switch on the front of the control box.
When set at CYCLE (down) the fan cycles on and off when cooling or heating. When set at CONT (continuous, up) the fan runs all the time. The unit is shipped in the CONT setting.

Temperature Limiting
Limiting the maximum and minimum settings prevents users from turning the control to the extreme heat or cool positions.
The normal range of the temp control is approximately 60°F to 85°F. The control range may be narrowed by the use of the temperature limiting screws located behind the control panel.

Vent Control
The vent control is located behind the front grille on the right side of the air discharge area. When set at CLOSE, only the air inside the room will be circulated and conditioned. When set at OPEN, some inside air is exhausted outside.

To open or close the vent:

1. Remove the front grille.
2. Remove and replace the vent card to the OPEN (mesh end toward the back) or to the CLOSE (mesh end toward the front) position.

Air Direction

Grille and Case

• Turn the air conditioner off and remove the plug from the wall outlet before cleaning.
• To clean, use water and a mild detergent. Do not use bleach or abrasives.

Outdoor Coils
The coils on the outdoor side of the air conditioner should be checked regularly.
If they are clogged with dirt or soot they may be professionally steam cleaned, a service available through your GE service outlet.

Front Grille
The front grille can be removed for more thorough cleaning or to make the model and serial numbers accessible.

To remove:

1. Pull the filter out.
2. Remove the two grille screws.
3. Pull the grille out from the bottom and lift up from the tabs on the top of the case.

To replace:
Hook the tabs on the front grille even with the tabs on the case and snap into place.
Replace the screws and filter.

To maintain optimum performance, clean the filter at least every 30 days.

Turn the air conditioner off before cleaning.
The most important thing you can do to maintain the air conditioner is to clean the filter at least every 30 days. A clogged filter reduces cooling, heating and air flow.

Keeping the air filter clean will

• Decrease cost of operation.
• Save energy.
• Prevent clogged heat exchanger coils.
• Reduce the risk of premature component failure.

To clean the air filters:

• Vacuum off the heavy soil.
• Run water through the filters.
• Dry thoroughly before replacing.
• To remove the air filter, on some models: Carefully pull the tab forward, up and out.

To remove the air filter, on other models:
Pull it down.

To replace the air filter:
Replace the clean filter by pushing it back into place.

CAUTION:

• Do not operate the air conditioner without the filter in place. If a filter becomes torn or damaged it should be replaced immediately.
• Operating without the filter in place or with a damaged filter will allow dirt and dust to reach the indoor coil and reduce the cooling, heating, airflow and efficiency of the unit.
• Replacement filters are available from your salesperson, GE dealer, GE Service and Parts Center or authorized Customer Care® servicers.

Read these instructions completely and carefully.

Before You Begin

• NOTE TO INSTALLER: Leave these instructions with the air conditioner after installation is completed.

• NOTE TO CONSUMER: Keep this Owner’s
  Manual and Installation Instructions for future use.

• IMPORTANT NOTES:

  • For personal safety, this air conditioner must be properly grounded.
  • It is important to have the wall outlet and circuit checked by a qualified electrician if there is any doubt as to whether a proper ground exists.
  • Follow National Electric Codes (NEC) and/or local codes and ordinances.

CAUTION:

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
• Do not change the plug on the power cord of this air conditioner.
• Aluminum house wiring may present special problems—consult a qualified electrician.

Electrical Requirements

Some models require 115/120-volt a.c., 60 Hz grounded outlet protected with a 15-amp time delay fuse or circuit breaker.
The 3-prong grounding plug minimizes the possibility of electric shock hazard. If the wall outlet you plan to use is only a 2-prong outlet, it is your responsibility to have it replaced with a properly grounded 3-prong wall outlet.
Some models require 230/208-volt a.c., protected with a time delay fuse or circuit breaker. These models should be installed on their own single branch circuit for best performance and to prevent overloading house
or apartment wiring circuits, which could cause a possible fire hazard from overheating wires.

Installing a J-Model in an existing wall case.

Read these instructions completely and carefully.

IMPORTANT!
GE strongly recommends the removal of the old wall case and the installation of a new GE Wall Case. If you decide to keep the existing wall case, you may need a kit to ensure proper
performance. If you DO NOT use a kit, you run the risk of poor performance or product failure. This is not covered under the terms of the GE warranty.

J-Model Qualifying Questions
J-model air conditioners may fit in existing wall cases. However, they often need a kit to properly adapt the case to the GE air conditioner. Answer these questions and see the chart below for the proper kit.

• What brand air conditioner will you be replacing?

• What are the dimensions of the wall case currently in use?

• What is the model number of the chassis currently in use?  What is the model (or Type) number of the wall case currently in use?
  Frequently, the J-model adapter kit will apply to another brand model “series” or specific vintage. In these cases, you need the chassis model number and/or the wall case or “type” number to confirm the use of the correct adapter kit.

• What type of outdoor grille is used with the current wall case?
  There may be an architectural grille attached to a wall case to enhance the exterior appearance of the building. Custom grilles may be used with J-model wall cases provided a J-model adapter kit is also used to ensure proper airflow.

GE Kit Numbers

Use GE
Kit Number:

RAK56A100

| For:

GE RAB13, 14 & 15 (ACLB & RCL Chassis)

| Description:

Fits all GE wall cases 26²W x 18²H x 24²D

---|---|---
RAK107| Hotpoint ACXB10 & 11 (ACTB Chassis)| Adapts an older Hotpoint wall case to a “J” model chassis. Fits Hotpoint wall cases 253⁄4²W x 167⁄8²H x 185⁄8²D
RAK108| Whirlpool Type 23W Wall Case| Adapts Whirlpool wall case to a “J” model chassis. Fits Whirlpool wall cases 257⁄8²W x 161⁄2²H x 231⁄8²D
RAK110| GE RAB30

(“F” models)

| Adapts GE wall case to a “J” model chassis. Fits the RAB 30 wall case 26²W x 18²H x 24²D
RAK123| Fedders Wall Case “A”| Adapts Fedders wall case to a “J” model chassis. Fits Fedders wall cases 27²W x 163⁄4²H x 163⁄4²D
RAK126| Westinghouse Wall Case (Type 2626D73H01)| Adapts Westinghouse wall case to a “J” model chassis. Fits Westinghouse wall cases 257⁄8²W x 157⁄16²H x 16²D
RAB46, 47 & 48| Use these kits for all other brands not listed.| Standard wall case for “J” model chassis. RAG13 stamped aluminum exterior grille included. Remove the existing case and replace.
RAK690| RAB36, 37, 38, 46, 47 or 48 (J-Chassis)| If you attach a custom architectural outdoor grille, use this kit to ensure proper airflow.
RAG14E| RAB36, 37, 38, 46, 47 or 48 (J-Chassis)| Architectural louvered exterior grille

Read these instructions completely and carefully.

Install the Air Conditioner in the Case.

• Remove the locking plate on the front left side.
• Remove the shipping pad inside the air conditioner next to the compressor.
• Carefully slide the air conditioner back into the case. Make sure that the tubing on the unit does not touch the wall case and that the case installation is secure.
• Reinstall the locking plate with the tab behind the wall case flange. Tighten the screw.
• Attach the power cord to the base pan with the clamp.
• When the wall outlet is to the left, extend the cord under the unit and hold it in place with the clamp.
• Attach the front grille. An opening for the power cord is on the bottom of the front grille.

Before You Call For Service…

Troubleshooting Tips
Save time and money! Review the chart on this page first and you may not need to call for service.

Normal Operating Sounds

• You may hear a pinging noise caused by water being picked up and thrown against the condenser on rainy days or when the humidity is high. This design feature helps remove moisture and improve efficiency.
• You may hear the thermostat click when the compressor cycles on and off.
• Water will collect in the base pan during high humidity or on rainy days. The water may overflow and drip from the outdoor side of the unit.
• The fan may run even when the compressor is not.

Air Conditioner Warranty.

All warranty service provided by our Factory Service Centers, or an authorized Customer Care® technician. To schedule service, on-line, 24 hours a day, contact us at www.GEAppliances.com, or call 800 -GE-CARES.

What GE Will Not Cover:

• Service trips to your home to teach you how to use the product.
• Improper installation. If you have an installation problem, or if the air conditioner is of improper cooling capacity for the intended use, contact your dealer or installer. You are responsible for providing adequate electrical connecting facilities.
• Failure of the product resulting from modifications to the product or due to unreasonable use including failure to provide reasonable and necessary maintenance.
• In commercial locations labor necessary to move the unit to a location where it is accessible for service by an individual technician.
• Replacement of house fuses or resetting of circuit breakers.
• Failure due to corrosion on models not corrosion-protected.
• Damage to the product caused by improper power supply voltage, accident, fire, floods or acts of God.
• Incidental or consequential damage caused by possible defects with this air conditioner.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

Consumer Support.

• GE Appliances Website
  Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals, order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™” your questions, and so much more…

• Schedule Service
  Expert GE repair service is only one step away from your door. Get on-line and schedule your service at your convenience 24 hours any day of the year! Or call 800-GE-CARES (800-432-2737) during normal business hours.

• Real Life Design Studio
  GE supports the Universal Design concept—products, services and environments that can be used by people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call 800-TDD-GEAC (800-833-4322).

• Extended Warranties
  Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still in effect. You can purchase it on-line anytime, or call 800-626-2224 during normal business hours. GE Consumer Home Services will still be there after your warranty expires.

• Parts and Accessories
  Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at 800-626-2002 during normal business hours.
  Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
  should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.

• Contact Us
  If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone number, or write to: General Manager, Customer

• Relations
  GE Appliances, Appliance Park Louisville, KY 40225

• Register Your Appliance
  Register your new appliance on-line—at your convenience! Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty, should the need arise. You may also mail in the pre-printed registration card included in the packing material, or detach and use the form in this Owner’s Manual.

www.GEAppliances.com
Printed in China

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>