ETI 564121120 Lighting 32-in Orbit Flush Mount, Color Preference Installation Guide
- June 4, 2024
- eti
Table of Contents
ETI 564121120 Lighting 32-in Orbit Flush Mount, Color Preference
Installation Guide
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: Shut off the power at the circuit breaker or fuse panel before
removing the old fixture, ballast, or fluorescent tubes.
If you are unfamiliar with electrical installations, we recommend you contact
a qualified electrician to do the installation.
PACKAGE CONTENTS
| Parts | Description | Quantity |
|---|---|---|
| A | Fixture | 1 |
| B | Wire Connector | 4 |
| C | Drywall Anchor | 4 |
| D | Mounting Screw | 2 |
INSTALLATION
Select a suitable location that can support the weight of the fixture. Determine the method of mounting before drilling.
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker before removing the existing light fixture or installing the new one.
With power disconnected to your electrical box, remove the existing fixture.
Make a sketch of how the current fixture is wired (by wire color) or mark the
wires with masking tape and a pencil so you will know how to properly
reconnect the wires to the new LED light fixture.
-
Rotate counterclockwise to remove the screw nut on the diffuser shade, then remove the external frame and diffuser shade and put them in a safe place.
-
With help from another person, temporarily hold the fixture base up to the ceiling to determine the best mounting position, mark four keyhole locations for mounting.
-
Drill a 1/8-in. pilot hole into the screw locations marked on the ceiling. You can also use an awl or nail to dimple the screw holes.
-
Install a drywall anchor (C) and a mounting screw (D) in each drilled mounting hole, but do not tighten fully.
NOTE: Do not drill hole on wooden surface.
-
Connect the hot and neutral (black and white) wires from the J-box to the same color wires from the fixture base.Connect the grounding wire from the J-box to the green wire from fixture base. Cover the wire connections using the wire connectors. Make sure to fasten them well.
-
Make the mounting screw (D) head cross the large ends of the keyholes on the fixture base, slide the base towards the narrow hole, and fasten these screws well.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. • SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 45°C. SUITABLE FOR DAMP LOCATIONS. MINIMUM 90°C SUPPLY CONDUCTORS. CAUTION-RISK OF SHOCK. DISCONNECT POWER BEFORE SERVICING.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver,
- connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
Support
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. – 5
p.m., CST, Monday – Friday
1-855-ETI-SSLI (1-855-384-7754)
www.ETiSSL.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>