ETI 504091120 9 Inch Rectangular Marine Bulkhead with Color Preference and Lumen Boost User Guide

June 4, 2024
eti

ETI 504091120 9 Inch Rectangular Marine Bulkhead with Color Preference and Lumen Boost

ETI 504091120 9 Inch Rectangular Marine Bulkhead with Color Preference and
Lumen Boost

PACKAGE CONTENTS

Part Description Quantity
A Lens 1
B Fixture Base 1
AA Drywall Anchors 4
BB Wire Nut 2
CC Fix Screw (for mounting) 4
DD Fix Screw (for J-box) 2
EE Gasket 1

504091120 9 Inch Rectangular Marine Bulkhead with Color Preference Package
Content

NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent tubes.
NOTE: Stick the replacement label on the inner wall of the recessed housing before installation.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.

INSTALLATION 1

**1** Open the lens (A) from the fixture base (B) by screwdriver, and disconnect
the connector between PCB and the driver,
504091120 9 Inch Rectangular Marine Bulkhead with Color Preference
Installation illustration
**2a** Mark 4 holes position and drill holes using Φ0.26in.(6.5mm), insert the
drywall anchors (AA) into the holes.
NOTE: Do not need drill holes on wooden surfaces.
504091120 9 Inch Rectangular Marine Bulkhead with Color Preference
Installation illustration
**3a** Put the Gasket (EE) on the back of fixture base (B). Drill 4 holes through the 4 markpoints of fixture base (B), connect the AC wires and the driver wires by wire nut (BB).
NOTE: AC wires should go through one of the 5 conduit entry holes on the fixture base (B).
504091120 9 Inch Rectangular Marine Bulkhead with Color Preference
Installation illustration
**4a** Align the holes on the fixture base (B) with the holes in the wall, and drill fix screws (CC) into the holes, lastly, silicone sealant (not included) around the 4 holes. Assemble the lens (A) with the fixture base (B) after connecting the connector of PCB and driver. Then tighten with lens screws. Apply silicone sealant (not included) between the fixture and the wall.
504091120 9 Inch Rectangular Marine Bulkhead with Color Preference
Installation illustration

INSTALLATION 2

**2b** Drill out the mark points in the fixture base (B) according with the
mounted J-box holes.
504091120 9 Inch Rectangular Marine Bulkhead with Color Preference
Installation illustration
**3b** Put the Gasket (EE) on the back of fixture base (B). Connect the AC wires and the driver wires by wire nut (BB). Mount the fixture base (B) into the j-box with fix screw (DD).
NOTE: AC wires should go through one of the 5 conduit entry holes on the fixture base (B).
504091120 9 Inch Rectangular Marine Bulkhead with Color Preference
Installation illustration
**4b** Assemble the lens (A) with the fixture base (B) after connecting the connector of PCB and driver. Then tighten with lens screws. Apply silicone sealant (not included) between the fixture and the wall.
504091120 9 Inch Rectangular Marine Bulkhead with Color Preference
Installation illustration

ADJUSTING THE COLOR TEMPERATURE AND LUMEN

This LED light fixture allows you to customize the color temperature and lumen.
Move the toggle switch on the fixture base (B) to make your selection before attaching the lens (A) to the fixture plate (B).
Choose the color temperature (CCT) from three options: 3000k Soft White, 4000k Cool White, or 5000k Daylight.
Choose the lumen from two options: high/ low lumen option (High for 100% brightness and low for 50% brightness).
NOTE: The factory setting for the correlated color temperature (CCT) is 3000K, and the lumen is 100% brightness
504091120 9 Inch Rectangular Marine Bulkhead with Color Preference
Installation illustration

WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.

  • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
  • This product must be installed in accordance with the applicable installation codes by a person familiar with the construction and operation of the product and the hazards involved.
  • Risk of electrical shock. To reduce the possibility of serious injury, always take the proper precautions and unplug the fixture before moving or cleaning.

NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV.
NOTICE: Suitable for operation in ambient temperatures not exceeding 113°F/45°C.

  • Suitable for wet locations.
  • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
    See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.

Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. – 5 p.m., CST, Monday – Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals