Sercomm SLMOD0 Corporation Device Database Instructions

Sercomm SLMOD0 Corporation Device Database

Specifications

• NFC Modulation: BLE Protocol
• Frequency Band: [Frequency Band]
• Activation: [Activation]
• Max Output Power: [Max Output Power]
• Microprocessor: [Microprocessor]
• Memory: [Memory]
• Transceiver RF Sensitivity: [Transceiver RF Sensitivity]
• Sensitivity (Conducted): [Sensitivity (Conducted)]
• Operating Temperature: [Operating Temperature]
• Mechanical Dimensions: [Mechanical Dimensions]

LoRaWAN Class A Operation
The product supports LoRaWAN class A operation, which allows for simplex transmission or reception capability. Please note that the reception capability is time-limited per the LoRaWAN protocol to
save battery consumption.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• 20cm away from body as per MPE

FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The final end product must be labeled in a visible area with the following: “Contains FCC ID: P27-SLMOD0”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met. This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification.

This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

Antenna and Transmitter Usage

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Ensure that the final end product is labeled with “Contains FCC ID: P27-SLMOD0” in a visible area. The grantee’s FCC ID can only be used when all FCC compliance requirements are met. If the transmitter is used in a co-located or simultaneous transmission with other transmitters or for portable use, a separate class II permissive change re-evaluation or new certification is required.

Please note that the certification of this transmitter module does not cover the FCC Part 15 Subpart B (unintentional radiator)  rule requirement applicable to the final host. The final host will need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions mentioned above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed.

SLMOD0

The product supports LoRaWAN class A operation which is a simplex transmission or reception capability. The reception capability is time-limited per the LoRaWAN protocol, in order to save battery consumption.

Listed below are the main performance characteristics

than -131dBm SF7/250KHz:+3dBr SF12/250KHz:+3dBr SF7/500KHz:+6dBr SF12/500KHz:+6dBr

FSK /50kbps: better than -109dBm

Operating temperature| From -40°C to +60°C non-condensing,
Mechanical dimensions (in millimeters)| L 20.8 mm x W 24.4 mm x H 3.6 mm
Operating Temperature| Range : -40°C to + 60°C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>