hp 711774-002 ProLiant Moonshot Server Installation Guide

June 17, 2024
HP

hp 711774-002 ProLiant Moonshot Server

Specifications

  • Product: HP ProLiant Moonshot Server
  • Part Number: 711774-002
  • Edition: 2
  • Date: May 2013

Registering the Server
To experience quicker service and more efficient support, register the product at the HP Product Registration website (http://register.hp.com).

Overview

Installation of a cartridge requires the following steps:

  1. Install the drive on the new cartridge, if needed.
  2. Install the cartridge in the chassis.
  3. Power up the chassis, if needed.

For definitions of the acronyms used in this document, see the “Acronyms and abbreviations” in the cartridge user and maintenance guide.

INSTALLATION

Installing the drive

  1. Extend the chassis from the rack.
  2. Remove the access panel.
  3. Remove the cartridge.
  4. Remove any drive installed on the cartridge.
  5. Install the drive as indicated.
  6. Install the cartridge.
  7. Install the access panel.
    For cartridge-specific information, see the cartridge user and maintenance guide on the HP Moonshot Information Library (http://www.hp.com/go/moonshot/docs).

Installing the cartridge

CAUTION: For proper cooling, be sure that a cartridge or a cartridge blank is always installed in each cartridge slot in the chassis. When replacing a cartridge, leave the cartridge slot empty for no more than 30 seconds. Failure to do so can disrupt airflow in the chassis.
IMPORTANT : After performing a procedure inside the chassis, always install the access panel on the chassis when complete. Do not operate the chassis for long periods with the access panel removed.

To install the component:

  1. Extend the chassis from the rack.
  2. Remove the access panel.
  3. Remove the cartridge blank or cartridge installed in the chassis.
  4. Prepare the cartridge.
  5. Align and install the cartridge into the chassis.
  6. Install the access panel.
  7. Slide the chassis into the rack.

Powering up the chassis
If the chassis was powered off while installing the cartridge, then power up the chassis. The cartridges are hot-pluggable and do not require that you power down the chassis for installation.

  1. Connect the power cables to the power supplies.
  2. Connect the power cables to the power source (UPS or wall outlet) or to an installed PDU.
  3. Wait while the chassis powers on. Verify the status of the chassis power LED located on the front panel display on the chassis. For more information on the chassis power LED status, see the HP Moonshot 1500 Chassis Setup and Installation Guide in the HP Moonshot Information Library (http://www.hp.com/go/moonshot/docs).

Configuring the cartridge

For more information on setting up and configuring the cartridges, see the HP Moonshot 1500 Chassis Setup and Installation Guide and the cartridge user and maintenance guide on the HP Moonshot Information Library (http://www.hp.com/go/moonshot/docs).

Installing the system software
To install the system software, see the HP Moonshot 1500 Chassis Setup and Installation Guide on the HP Moonshot Information Library (http://www.hp.com/go/moonshot/docs). For information about operating systems supported by the Moonshot System, see the operating system support matrices (http://www.hp.com/go/supportos).

Registering the server
To experience quicker service and more efficient support, register the product at the HP Product Registration website (http://register.hp.com).

For more information
For more detailed setup and configuration information, see the HP Moonshot 1500 Chassis Setup and Installation Guide on the HP Moonshot Information Library (http://www.hp.com/go/moonshot/docs).

Safety and regulatory compliance
For safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products, available at the HP website
(http://www.hp.com/support/Safety-Compliance-EnterpriseProducts) .

Documentation feedback
HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback
( mailto:docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback.

FAQ

  • Q: Where can I find the cartridge user and maintenance guide?
  • Q: Can I install a cartridge without powering down the chassis?
    • A: Yes, the cartridges are hot-pluggable and do not require you to power down the chassis for installation.
  • Q: How can I check the status of the chassis power LED?
    • A: You can check the status of the chassis power LED located on the front panel display on the chassis. For more information, refer to the HP Moonshot 1500 Chassis Setup and Installation Guide in the HP Moonshot Information Library (http://www.hp.com/go/moonshot/docs).

Copyright 2013 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are outlined in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals