Maxspect LS-090 Lagoon Series Smart Aquarium User Guide

Maxspect LS-090 Lagoon Series Smart Aquarium

Aquarium Installation

1. Cabinet
   

2. Door Panel
   

3. Display Tank
   

4. Sump
   

5. Plumbing
   

6. Integrated Control Center
   

7. Gyre Flow Pump and Skimmerhttps://get-qr.com/UpgkR1
   

Equipment Connection

Control Panel
Power Supply (Backup)
Return Pump (Backup)
Return Pump
Power Supply 1**
Temp. Sensor 1
Temp. Sensor 2
Overflow Sensor
Skimmer Overflow Sensor
V Protein Skimmer
Gyre Flow Pump B
Gyre Flow Pump A
Refugium Light
Power Supply 2***

• Tips: When the main control system is failed, please first connect the Return Pump and Power Supply 1 to the Return Pump (Backup) and Power Supply (Backup) sockets respectively, now the Power Supply 1 only powers the return pump, the other equipment stops working. Then please contact local retailer or manufacturer for after-sale service.
  ** Power Supply 1 only powers the Return Pump and the main control system.
  *** Power Supply 2 powers the rest equipment.

Scan QR Code to download Syna-G Cloud AP

Operation

Equipment Control

• Press button can switch between the two main interfaces.
• When in the main interface 1, press and hold button for about 2s to enter setting interface，press again button to switch among the equipment，press － or ＋ button to set the value，then press and hold button again for about 2s，or leave it for 30s to save the setting and.
• Protein Skimmer & Return Pump: you can set the working speed of the equipment on both the control panel and the APP.
• Refugium Light & Gyre Flow Pump：you can only turn on and off the light through the control panel, please use the APP to get full access to the equipment.

Wi-Fi Connection

1. On either of the main interface，press and hold all three buttons for about 3s to enter setting interface;
2. Press － or ＋ button to switch to setting page 1(WiFi)；
3. Press and hold button for about 2s until the WiFi indicator starts to flash, now the system is ready to be connected;
4. Open Syna-G Cloud APP to connect the system by following the hints; *
5. Create an account and log in; **
6. For Android platform, choose the WiFi connection to which your mobile device has already connected and input password;
7. When a fixture with the ID “AT1-A1xxxxxx” is shown on the list, it means that the fixture is connected to your mobile device successfully.

• Make sure your mobile device is connected to a 2.4GHz or 2.4GHz & 5GHz combined network, and turn on the Bluetooth signal and GPS positioning function at the same time.
  **Select a proper territory on the right up side of the login page while register new account。

Turn On/Off the System

1. On either of the main interface, press and hold all three buttons for about 3s to enter setting interface;
2. Press － or ＋ button to switch to setting page 2(OFF)；
3. Press and hold button for about 2s until the display flashes for three times, the system turns off and all the equipment stop working, however the WiFi connection is still activated；
4. Press and hold all three buttons again for about 2s can turn on the system.

Restore Factory Setting

1. On either of the main interface, press and hold all three buttons for about 3s to enter setting interface;
2. Press － or ＋ button to switch to setting page 3(Reset)；
3. Press and hold button for about 2s，system is restored to factory setting after the display flashing for three times.

Child Safety Lock

1. On either of the main interface, press and hold – & + buttons for about 2s to lock the buttons, however you can still press button to check out equipment status.
2. Press and hold – & + buttons again for about 2s can unlock the buttons.

Water Exchange

1. Press and hold － & buttons for about 2s to enter water exchange mode, return pump, gyre flow pump and skimmer stop working;
2. The duration of water exchange can only be set through the APP, the equipment will not recover to its previous working status automatically after the time is up and the buzzer starts to beep;
3. Press and hold － & buttons again for about 2s can exit water exchange mode.

Feeding

1. Press and hold & ＋ buttons for about 2s to enter feeding mode, return pump keeps its working speed, skimmer and gyre flow pump slow down to 10% working speed；
2. The duration of feeding can only be set through the APP, the equipment will recover to its previous working status after the time is up；
3. Press and hold & ＋ buttons again for about 2s can exit feeding mode.

Customer Support

Scan QR Code to watch installation video

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>