REGISDESK Standing Desk-63RC Electric Height Adjustable Desk Instruction Manual

REGISDESK Standing Desk-63RC Electric Height Adjustable Desk

Specifications

• Model No#: [insert model number]
• Indoor Use: For indoor use only.

Instructions:

Attention:

• Assembly Safety: Wear protective gloves when assembling.
• Bolt Tightening: Do not fully tighten bolts until assembly is complete.
• Floor Surface: Highly recommend assembling on carpeted floor to prevent scratches.
• Lifting Precaution: Before lifting, ensure clear surroundings and free desk power cord movement during height adjustments.
• Cleaning and Maintenance: Avoid spraying cleaning solutions on the desk; use a dry or slightly damp cloth. Keep electrical components dry, don’t open them, and don’t modify the provided plug. Turn off power before removing the adapter, and perform monthly checks to ensure proper desk function.

Part List:

• Lift Column (with motor)
• Lift Column (without motor)
• Cross-Bar (left)
• Cross-Bar (right)
• F-Side Bracket (right)
• Extendable Bar (left)
• Sync Rod (long)
• AC Adapter
• Controller
• Power Cord
• Keyboard Tray Slider Bracket Set
• Slider Bracket Connectplate (right)
• Slider Bracket Connectplate (left)
• Keyboard Tray Anti-Slip Plate
• Drawer A
• Drawer B
• Drawer Base A
• Drawer Base B
• Board-6
• Board-7
• Board-8
• Keyboard Tray Board
• Drawer Anti-Slip Board
• Storage Shelf Board
• Long Screws
• Wood Pin

Installation Steps:

Step 1 – Step 4:

1. Insert the extendable bar to the cross-bar.
2. Do not fix them by screws before finishing the whole frame assembly.
3. Install lift column to cross bar (finished in step 1) with 12 pcs of M6 x 12mm screws. (5mm Allen Key)
4. Connect the side brackets (left & right) and hooks to the lift column with 4 pcs M6x12 screws (5mm Allen Key)

Step 5 – Step 8:

5. Fasten desktop to the frame with 8 pcs M6x12 screws.(5mm Allen Key)
6. Holding sync rod with one hand, insert the shaft to the motorized lift column making sure the rod contacts the bumper on the motor shaft.
7. Loose and extend hex shaft and make it through sync rod transformer then insert it into the lift column fully. (without motor)
8. Tighten both knobs.
9. Adjust the extendable to the right position.
10. Fasten the cross-bar and extendable bar fully with 8 pcs M6x12 screws. (5mm Allen Key)

Step 9 – Step 12

9. Fasten the desktop to the frame fully by 4 pcs M6x12 screws. (5mm Allen Key)
10. Insert 8 pcs 3-in-1 screws into the desktop.
11. Connect each 2 pcs boards-3&4 to boards-2.
12. Fasten them by 8 pcs 3-in-1 nuts.(Screw Driver)
13. Install 2 pcs board-5 to each board-3&4.
14. Fasten them by 8 pcs long screws.(Screw Driver)
15. Install 2 pcs board-6 to each board-3&4.

FAQ

Can I use this desk outdoors?

No, this desk is designed for indoor use only.

Do I need to wear protective gloves during assembly?

Yes, it is recommended to wear protective gloves when assembling the desk.

Should I fully tighten the bolts during assembly?

No, do not fully tighten bolts until assembly is complete.

Can I assemble the desk on a non-carpeted floor?

It is highly recommended to assemble the desk on a carpeted floor to prevent scratches.

What precautions should I take when lifting the desk?

Before lifting, ensure clear surroundings and free desk power cord movement during height adjustments.

How should I clean and maintain the desk?

Avoid spraying cleaning solutions on the desk; use a dry or slightly damp cloth. Keep electrical components dry, don’t open them, and don’t modify the provided plug. Turn off power before removing the adapter, and perform monthly checks to ensure proper desk function.

PLEASE READ THIS MANUAL CAREFULLY BRFORE ASSEMBLY

INSTRUCTIONS

ATTENTION

• Indoor Use: For indoor use only.
• Assembly Safety: Wear protective gloves when assembling.
• Bolt Tightening: Do not fully tighten bolts until assembly is complete.
• Floor Surface: Highly recommend assembling on carpeted floor to prevent scratches.
• Lifting Precaution: Before lifting, ensure clear surroundings and free desk power cord movement during height adjustments.
• Cleaning and Maintenance: Avoid spraying cleaning solutions on the desk; use a dry or slightly damp cloth. Keep electrical components dry, don’t open them, and don’t modify the provided plug. Turn off power before removing the adapter, and perform monthly checks to ensure proper desk function.

PART LIST

INSTALLNATION STEPS

1. Insert the extendable bar to cross-bar.
   Do not fix them by screws before finished the whole frame assembly.

2. Install lift column to cross bar (finished in step 1) with 12 pcs of M6 x 12mm screws. (5mm Allen Key)

3. Connect the side brackets (left & right) and hooks to the lift column with 4 pcs M6x12 screws (5mm Allen Key)
4. 1. Install and fix 2 bases to lift columns with 8 pcs M6x16 screws.(5mm Allen Key)

5. Connect and fix the desk top board with 4 pcs wood pins.
   Fasten them by plastic plate and 12pcs M6×12 screws.(5mm Allen Key)

6. Fasten desktop to the frame with 8 pcs M6x12 screws.(5mm Allen Key)

7.  Holding sync rod with one hand, insert the shaft to the motorized lift column making sure the rod contacts the bumper on the motor shaft.
8. Loose and extend hex shaft and make it through sync rod transformer then insert it into the lift column fully. (without motor）
9. Tighten both knobs.
10. Adjust the extendable to the right position.
    Fasten the cross-bar and extendable bar fully with 8 pcs M6x12 screws. (5mm Allen Key)

9. Fasten the desktop to frame fully by 4 pcs M6x12 screws. (5mm Allen Key)
10. Insert 8 pcs 3-in-1 screws into the desktop.
11. Connect each 2 pcs boards-3&4 to boards-2.
12. Fasten them by 8 pcs 3-in-1 nuts.(Screw Driver)

11. Install 2 pcs board-5 to each board-3&4.
    Fasten them by 8 pcs long screws.(Screw Driver)

12. Install 2 pcs board-6 to each board-3&4.
    Fasten them by 8 pcs long screws.(Screw Driver)

13. Assembly right and left slider bracket plate to the slider bracket and fasten them with 10 pcs M5x5 screws.(Screw Driver)
14. Assembly anti-slip plate and 2 slinder bracket set to the keyboard tray board and fasten them with 8 pcs M4x12 screws.(5mm Allen Key)

15. Assembly keyboard tray set to the desktop and fasten them with 4 pcs M6x12 screws.(5mm Allen Key)
16. Overturn the desk and insert 8 pcs 3-in-1 screws to the board-2

17. Assembly each 2 pcs board-7&8 to the board -2 and fasten them with 8 pcs 3-in-1 nuts. (Screw Driver)
18. Insert 8 pcs 3-in-1 screws to stroage shelf board.
    Assembly stroage shelf board to board-7&8 and fasten them with 8 pcs 3-in-1 nuts. (Screw Driver)

19. Assembly drawer anti-slip board of the drawer
    Fasten them with 8 pcs long screws.

20. Install 4 set drawes.

21. Install the controller to the desktop with 2 pcs 4×12 screws.
    Install the AC adapter to the desktop with 2 pcs 4×12 screws.

22. Plug the cable from the motor to the controller
    Plug the cable from AC adapter to controller
    Plug the power cord to the AC adapter

23. Complete the installnation.

AFTER SERVICE

• Thank you for choosing to purchase our product! We are honored to provide you with outstanding products and services. We deeply appreciate your trust and support, which means a great deal to us.

• If you encounter any issues, have questions, or require further assistance while using our product, our dedicated customer support team is available to assist you. Please don’t hesitate to contact us via the following email address:
  Email Address: rjyyamazoncs@163.com

• Whether your inquiries are related to product usage, maintenance, or any other aspect, we are committed to providing you with the best solutions.

• Once again, thank you for your support. We look forward to serving you and ensuring a pleasant and seamless shopping experience.

• Wishing you a joyful life and enjoyable use of our product!

CONTROLLER INSTRUCTIONS

LIFT UP OR DROP DOWN

1.  When button is long pressed, the desk will move up and down until it is released or reaches the lowest/ highest point.
2. When short press the key, the desk will move a short distance accordingly.

POSITION MEMORY SETTINGS & OPERATION

3 POSITIONS MEMORY CAN BE STORED.

1. When moving to a specific position, press “S” until the digital “S-” flashes then press “1/ 2/ 3” button and current height is stored to the corresponding label successfully
2. Short press the”1 /2/ 3″ button the indicator display will show the height of the position memory
3. Long press or double press the”1 /2/ 3″ button and the desk will automatically move to the height accordingly During operation, any button can stop the operation.

ZERO POSITION RESET.
Long press “S” for 3 seconds and wait for the indicator display to show “—” then the desk will automatically move downwards and upwards. After the end, the desk will automatically move to a fixed position and the zero-position successfully reset.

FACTORY RESET
Press and hold “S” + “2” for 5 seconds. when the indicator display shows “CLr” it means that the setting is successfully.

LOCK & UNLOCK SETTING

• Lock: Press and hold “S” + “1” for 5 seconds. when the indicator display shows “L” it means that the setting is locked and cannot be lifted or lowered.
• Unlock: Press and hold “S” + “1” for 5 seconds. when the indicator display shows from “L ” to normal digital display, it means the setting has been unlocked.
  

TROUBLESHOOTING

please recon- nect the motor
E02| Motor overcurrent| Press the up or down button again, if it still exists, please replace the motor or reduce the load.

E03

|

Motor Hall failure

| Press the up or down button again, but if it still exists, please check the connection or replace the motor.
E04| Abnormal main power| It cannot be fixed after power failure, replace the power supply.
E05| Abnormal motor current|

It cannot be fixed after power failure, replace the power supply.

E06

| Motor power device is broken|

Please contact customer service department for advice

E08| Temperature warning| Wait for the temperature to cool down.
E09| Motor stall| Press the up or down button again, if it still exists, please replace the motor or reduce the load.
RST| Unexpected power down| Reduce the load or check if the power cable is loose.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>