MOUNTUP MU0008 UL Listed TV Wall Mount Instruction Manual
- June 14, 2024
- MOUNTUP
Table of Contents
MU0008 UL Listed TV Wall Mount
Instruction Manual
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
Safety Caution
Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.
-
This product is designed for use in wood stud or solid concrete wall.
– DO NOT install into drywall alone. -
The wall must be capable of supporting five times the weight of the TV and mount combined.
-
Incorrect installation may result in product damage / property damage or body injury.
We shall bear no responsibility for any damage or injury resulted from
incorrect installation, incorrect assembly or misuse.
WARNING : This product contains small items that could be a choking
hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any
parts are missing or damaged, do not return the damaged item to your dealer;
please contact our customer service team. Never use damaged parts!
Must Check Before Getting Started
Minimum VESA Pattern (W × H): 150mm × 100mm / 6 in × 4 in
Maximum VESA Pattern (W × H): 600mm × 400mm / 24 in × 16 in
WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended
for use only within the maximum weights indicated. Use with products heavier
than the maximum weights indicated may result in failure of the mount and its
accessories, causing possible damage or injury.
Verify Your Wall Construction
CAUTION:
Avoid potential personal injuries and property damage!
Drywall covering the wall must not exceed 5/8 in. (16 mm).
Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in.
(38 x 89 mm). CAUTION:
Avoid potential personal injuries and property damage!
Mount the wall plate assembly directly onto the concrete surface (no surface
covering).
CAUTION : DO NOT install into drywall alone.
Product Dimensions
Supplied Parts and Hardware
Wall / Product
TV
NOTE: Not all parts and hardware included will be used.
Extra Tools You Need (Not Supplied)
Attach Brackets to TV
1-1 Select TV Screws
1-2 Need Spacer
- Yes, choose the appropriate screws, washers,and spacers for your TV
- No, just choose the screws, washers.
1-3
Do not tighten the screws excessively or tighten them by using the Electrodrill, or your TV might be damaged.
Tilting Adjustment
Option : To keep TV in vertical position, please use two M4 screws (MA) to insert the holes on two brackets respectively.
Assemble Wall Plate
3-1 ssemble two wall plates (H) with bolts (C), washers (D) and nuts (E).
Keep the upside of the two wall plates (H) horizontal, and then use wrench (B)
to fasten the nuts (E).
3.2 Buckle the Wall Plate Cover (K) on the Wall Plate (H).
4-2 Attach Wall Plate to Wall
OPTION A: Wood Stud Installation
Locate your studs. Verify and mark the center of the stud by finding the stud
edges using awl and stud finder.
Line up the holes with your stud center line. Level the wall plate and mark
the pilot hole locations.
Drill pilot holes using a Ф7/32 in (Ф5.5mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located. Be
sure to drill into the center of the stud.
Install wall plate using lag bolts with Socket Wrench, NO Electrodrill.
A No anchors when installed onto the wood studs.
CAUTION :
To avoid potential personal injury or property damage:
All 4 lag bolts MUST BE firmly tightened to prevent unwanted movement of the
wall plate assembly. Ensure the wall plate assembly is securely fastened to
the wall before continuing on to the next step.
4-BAttach Wall Plate to Wall
OPTION B: Solid Concrete Wall Installation
Drill pilot holes using a Ф3/8 in (Ф10mm) diameter drill bit.
IMPORTANT : Do not drill holes into where water pipes or electrical wires
are located, or mortar between blocks.
Use the hammer to knock anchors (not included) into the concrete wall. Be sure
the anchors are seated flush with the concrete surface.”
Install wall plate using lag bolts and anchors (not included) with Socket A
Wrench, NO Electrodrill.
CAUTION:
To avoid potential personal injury or property damage:
All 4 lag bolts MUST BE firmly tightened to prevent unwanted movement of the
wall plate assembly. Ensure the wall plate assembly is securely fastened to
the wall before continuing on to the next step.
Hang and Secure TV to Wall Plate
5-1 Before hanging TV, please conduct “wall plate installation integrity test” first.
5-2 Hang and secure TV assembly onto the wall plate
CAUTION:
Avoid potential personal injury or property damage! Always make sure your TV
brackets are in the locked position so the TV is securely attached to the wall
plate assembly.
If necessary
Take down the TV from the Mount
Pull down the straps to release the locking latch.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>