REGISDESK 230925 Shaped Standing Desk with 4 Drawers Instruction Manual

REGISDESK 230925 Shaped Standing Desk with 4 Drawers

INSTRUCTIONS

ATTENTION

• Indoor Use: For indoor use only.
• Assembly Safety: Wear protective gloves when assembling.
• Bolt Tightening: Do not fully tighten bolts until assembly is complete.
• Floor Surface: Highly recommend assembling on carpeted floor to prevent scratches.
• Lifting Precaution: Before lifting, ensure clear surroundings and free desk power cord movement during height adjustments.
• Cleaning and Maintenance: Avoid spraying cleaning solutions on the desk; use a dry or slightly damp cloth. Keep electrical components dry, don’t open them, and don’t modify the provided plug.
  Turn off power before removing the adapter, and perform monthly checks to ensure proper desk function.

PART LIST

| | |
---|---|---|---

LIFT CILUMN (with motor)

| LIFT CILUMN (without motor)| CROSS-BAR (left)| CROSS-BAR (right)
| | |

CROSS-BAR (right)

| EXTENDABLE BAR| EXTENDABLE BAR (right side)| F- SIDE BRACKET (LONG)
| | |
F- SIDE BRACKET (short)| BASE (long)| BASE (short)|

SYNC ROD TRANSFORMER

| **| | **

CONNECT PLATE

| R- HOOK| SYNC ROD (long)| SYNC ROD (short)
**| | |
SYNC ROD CONNECTER| AC ADAPTER| POWER CORD**|

CONTROLLER

| | |

DRAWER

| DRAWER BASE| PLASTIC CONNECT| PLASTIC COVER
| | |
DESK TOP BOARD| SIDE BOARD| BOARD4|

SYNC ROD (short)

| |

BOARD6

| BOARD7| BOARD8
| | |
5MM ALLEN KEY| 4MM ALLEN KEY| 3MM ALLEN KEY|

2.5MM ALLEN KEY

| | |

4.2×13 screws

| M5×30 screws| M6×12 screws| M6×16 screws
| | |
M6 3in1 screws| 3in1 nut| Long screws|

wood pin

**| |
M6×12 screws| 4×12 screws**|

SCREWDEIVER

INSTALLATION STEPS

STEP 1—STEP 4

1. Insert the extendable bar to cross-bar.
2. Do not fix them by screws before finished the whole frame assembly.

1. Install lift column (one with motor) to cross bar (finished in step 1) with 12 pcs of M6 x 12mm screws. (5mm Allen Key)

1. Install lift column (the one with motor) to cross bar (finished in step 1) with 12 pcs of M6 x 12mm screws. (5mm Allen Key)
2. Holding sync rod with one hand, insert the shaft to the motorized lift column making sure the rod contacts the bumper on the motor shaft.
3. Loose and extend hex shaft and make it through sync rod transformer then insert it into the lift column fully. (without motor）
4. Tighten both knobs.

1. Fix sync rod transformer to crossbar with 2pcs M5x30 screws.(4mm Allen Key)

STEP 5—STEP 8

1. Fix the connect plate to the cross-bar frame with 4 pieces M6x12 screws.(5mm Allen Key)

1. Insert side extendable bars into crossbars and fix them to the lift column with M6x12 screws.(5mm Allen Key)

1. Connect side frame (finished in step 4) to the main frame with 4 pcs M6x12 screws. (finished in step 5)(5mm Allen Key)

1. Connect the side brackets and hooks to the frame with 6 pcs M6x12 screws(5mm Allen Key)

STEP 9—STEP 12

1. Fix the base to the frame with 12 pieces M6x16 screws.(5mm Allen Key)
2. Insert sidesync rod connecter to the side lift column by hand.

1. Insert side short sync rod to sync rod connecter and sync rod transformer by hand.

1. Connect and fix the desk top board with 8 pcs wood pins.
2. Fasten them by plastic plate and 24pcs M6×12 screws.(5mm Allen Key)

1. Install the desktop to the frame with 11 pieces M6x12 screws.(5mm Allen Key)

STEP 13—STEP 16

Fasten cross-bar and extendable bar with 12 pieces M6x12 screws.(Screw Driver)

Lock short sync rod to sync rod transformer by 2.5mm Allen Key

Fasten the desktop to the frame with 6 pcs 4.2×13 screws.(Screws Driver)

1. Connect 4/5/6-boards with 4 pcs wood pins.
2. Insert 14 pcs 3-in-1 screws into the 4/5/6-boards.
   

STEP 17—STEP 20

1. Insert 14 pieces 3-in-1 screws into the desktop
2. Put 7 pcs 9-boards above the desktop then fasten them by 14 pcs 3-in-1 nuts

1. Put 4/5/6-boards onto 9-boards
2. Fasten them by 14 pcs 3-in-1 nut

1. Connect 2 pcs 8 board with 2 pcs wood pin
2. Fix board 7/8 to side boards with 7pcs long screws.(3mm Allen Key)

Install 4 set draws.

STEP 21-23

1. Install the controller to the desktop with 2 pcs 4×12 screws.
2. Install the AC adapter to the desktop with 2 pcs 4×12 screws.

1. Plug the cable from the motor to the controller
2. Plug the cable from AC adapter to controller
3. Plug the power cord to the AC adapter

Complete the install nation.

AFTER SERVICE

Thank you for choosing to purchase our product! We are honored to provide you with outstanding products and services. We deeply appreciate your trust and support, which means a great deal to us.

If you encounter any issues, have questions, or require further assistance while using our product, our dedicated customer support team is available to assist you. Please don’t hesitate to contact us via the following email address:

Email Address: rjyyamazoncs@163.com

Whether your inquiries are related to product usage, maintenance, or any other aspect, we are committed to providing you with the best solutions.

Once again, thank you for your support. We look forward to serving you and ensuring a pleasant and seamless shopping experience.

Wishing you a joyful life and enjoyable use of our product!

| QTY REQUEST| QTY IN THE BAG| REMARK
---|---|---|---
1| | M6×12 screws| 75| 77|
2| | M6×12 screws| 4| 6|
3| | M6×16 screws| 12| 14|
4| | 4.2×13 screws| 6| 7|
5| | M5×30 screws| 7| 9|
6| | M5×30 screws| 2| 4|
7| | 3in1 screw| 28| 30|
8| | 3in1 nut| 28| 30|
9| | 4×12 screw| 4| 6|
10| **| woos pin| 14| 16**|

CONTROLLER INSTRUCTIONS

LIFT UP OR DROP DOWN

1. When ” ▲ ” or ” ▼ “button is long pressed, the desk will move up and down until it is released or reaches the lowest/ highest point.
2. When short press the ” ▲ ” or ” ▼ ” key, the desk will move a short distance accordingly.

POSITION MEMORY SETTINGS & OPERATION

POSITIONS MEMORY CAN BE STORED.

1. When moving to a specific position, press “S” until the digital “S-” flashes then press “1/ 2/ 3” button and current height is stored to the corresponding label successfully
2. Short press the”1 /2/ 3″ button the indicator display will show the height of the position memory
3. Long press or double press the”1 /2/ 3″ button and the desk will automatically move to the height accordingly During operation, any button can stop the operation.

ZERO POSITION RESET.

Long press “S” for 3 seconds and wait for the indicator display to show “—” then the desk will automatically move downwards and upwards. After the end, the desk will automatically move to a fixed position and the zero-position successfully reset.

FACTORY RESET

Press and hold “S” + “2” for 5 seconds. when the indicator display shows “CLr” it means that the setting is successfully.

LOCK & UNLOCK SETTING

Lock: Press and hold “S” + “1” for 5 seconds. when the indicator display shows “L” it means that the setting is locked and cannot be lifted or lowered.
Unlock: Press and hold “S” + “1” for 5 seconds. when the indicator display shows from “L ” to normal digital display, it means the setting has been unlocked.

TROUBLESHOOTING

please recon- nect the motor
E02| Motor overcurrent| Press the up or down button again, if it still exists, please replace the motor or reduce the load.
E03| Motor Hall failure| Press the up or down button again, but if it still exists, please check the connection or replace the motor.
E04| Abnormal main power| It cannot be fixed after power failure, replace the power supply.
E05| Abnormal motor current| It cannot be fixed after power failure, replace the power supply.
E06| Motor power device is broken| Please contact customer service department for advice
E08| Temperature warning| Wait for the temperature to cool down.
E09| Motor stall| Press the up or down button again, if it still exists, please replace the motor or reduce the load.
RST| Unexpected power down| Reduce the load or check if the power cable is loose.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>