LANCOM LN-860 Indoor Access Point User Guide
- June 16, 2024
- LANCOM
Table of Contents
LANCOM LN-860
LANCOM LN-862
Quick Reference Guide
LN-860 Indoor Access Point
Wi-Fi antennas (only LN-862)
Screw the supplied Wi-Fi antennas onto the connectors WLAN 1 Ant 1 / Ant 2 and
WLAN 2 Ant 1 / Ant 2.
The desired MIMO behaviour can be configured under
- Physical WLAN Settings
- Radio
- Antenna grouping
Power
After connecting the cable to the device, turn the connector 90° clockwise to
prevent it from accidental un plugging. Use only the supplied power adapter.
Ethernet interface
Use the cable with the Ethernet connectors to connect interface ETH1 (PoE) or
ETH2 to your PC or a LAN switch.
Serial interface
You can optionally configure the device by connecting it to a PC with a
configuration cable (separately available). Please observe the following
when setting up the device
- For devices to be operated on the desktop, please attach the adhesive rubber footpads
- Do not rest any objects on top of the device
- Keep the ventilation slots on the side of the device clear of obstruction
- Lockable wall and ceiling mounting with the LANCOM Wall Mount (LN) (available as an accessory)
Please note that when operating both Wi-Fi modules in the same frequency band, mutual interference cannot be ruled out https://manual-hub.com/
MOUNTING AND CONNEC TING THE DEVICE
Power
Off | Device switched off |
---|---|
Green, permanently* | Device operational |
resp. device paired / claimed and LANCOM Management Cloud (LMC) accessible.
Orange, permanently| No adequate PoE-power supply via 802.3af, operation of
the second Wi-Fi interface not possible
Red / green, blinking| Configuration password not set. Without a configuration
password, the configuration data in the device is unprotected.
Orange / green blinking alternately with the WLAN link LED| At least one Wi-Fi
module is in
managed mode and has not found a WLAN controller yet. The corresponding Wi-Fi
module(s) is/are switched off until a WLAN controller has been found to supply
a configuration, or until being switched manually into another operating mode.
Orange / red
blinking alternately with the WLAN link LED| At least one Wi-Fi module is in
managed mode and has found a WLAN controller. However, the WLAN controller
cannot assign a configuration because the firmware and/or the device’s loader
version is not compatible with the WLAN controller.
lx green inverse ‘
blinking| Connection to the LMC active, pairing OK, claiming error.
2x green inverse blinking| Pairing error, resp.
LMC activation code / PSK not available.
3x green inverse blinking*| LMC not accessible, resp. communication error.
WLAN link
Off| No Wi-Fi network defined or Wi-Fi module deactivated. The Wi-Fi module is
not transmitting beacons.
---|---
Green, permanently| At least one Wi-Fi network defined and Wi-Fi module
activated. The Wi-Fi module is transmitting beacons.
Green, inverse flashing| Number of flashes = number of connected Wi-Fi
stations and P2P wireless connections, followed by a pause (default).
Alternatively the flashing frequency can indicate signal strength over the
defined P2P link or the signal strength between the access point and the
device operating in client mode.
Green, blinking Red, blinking| DFS scanning or other scan procedure.
Red, blinking| Hardware error in the Wi-Fi module.
*) The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Management Cloud.
TECHNIC AL DET AILS
Hardware|
---|---
Power supply| 12 V DC, external power adapter (110 or 230 V) with bayonet
connector to secure against disconnection or PoE based on 802.3at via ETH1
Power consumption| Approx. 15.1 W via 12 V / 2 A power adapter (value refers
to the total power consumption of access point and power adapter),
Approx. 14.9 W via PoE (value solely refers to the power consumption of the
access point)
Environment| Temperature range 0–45 °C (vertical wall mount with LANCOM Wall
Mount (LN)), 0-37 °C (horizontal ceiling mount with LANCOM Wall Mount (LN))
Access point overheating is avoided by automatic throttling of the Wi-Fi
modules Humidity 0-95 %; non-condensing
Housing| Robust synthetic housing, rear connectors, ready for wall and ceiling
mounting; measures 205 x 42 x 205 mm (W x H x D)
Number of fans| None; fanless design, no rotating parts, high MTBF
Wi-Fi|
Frequency band| 2400-2483.5 MHz (ISM) or 5180-5700 MHz (restrictions vary
between countries)
Radio channels 2.4 GHz| Up to 13 channels, max. 3 non-overlapping (2.4 GHz
band)
Radio channels 5 GHz| Up to 19 non-overlapping channels (automatic dynamic
channel selection required)
Interfaces|
ETH1 (PoE)| 10 / 100 / 1000 Base-TX, autosensing, auto node hub,
PoE adapter compliant with IEEE 802.3at required
ETH2| 10 / 100 / 1000 Base-TX, autosensing, auto node hub
Serial interface| Serial configuration interface / COM-port (8-pin mini-DIN):
9,600 – 115,000 baud
Declaration of conformity
Hereby, LANCOM Systems declares that this radio equipment is in compliance
with Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: www.lancom-
systems.com/ce/
Package content
Documentation | Installation Guide (DE/EN), Quick Reference Guide (DE/EN) |
---|---|
Antennas (only LN-862) | Four 3 dBi dipole dual-band antennas |
Cable | Ethernet cable, 3 m |
Power adapter | External power adapter, NEST 12 V / 1.5 A DC/S, barrel |
connector 2.1 / 5.5 mm bayonet, LANCOM item no. 111507 (EU, 230 V); LANCOM item no. 111302 (UK, 230 V)
LANCOM, LANCOM Systems and LCOS are registered t ademarks. All other names or descriptions used may be tr ademarks or registered trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 111553/0118
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>