eta MONETO II Stick Vacuum Cleaner 2 in 1 Instructions

eta MONETO II Stick Vacuum Cleaner 2 in 1

Product Information

Specifications

• Model: MONETO II
• Date: 2/1/2024
• Power Source: Li-Ion Battery
• Battery Voltage: 14.4 V / 18 V / 21.6 V / 25.2 V
• Battery Capacity: Approximately 1.2 Ah / 2.5 Ah
• Dimensions: 420 mm x 110 mm x 135 mm
• Weight: 260 mm x 170 mm x 1155 mm

Product Usage Instructions

Safety Warning
Ensure to read and follow all safety instructions provided in the user manual before using the product.

Equipment and Accessories
The product comes with the following equipment and accessories:

• Fig. 1 – Vacuum cleaner

Vacuum Cleaner Preparation
Before using the vacuum cleaner, make sure it is properly prepared:

• Connect the vacuum cleaner to a power source using the provided power cord.
• Ensure the battery is fully charged.

Use of Vacuum Cleaner
To use the vacuum cleaner, follow these steps:

1. Switch on the vacuum cleaner using the power button.
2. Adjust the suction power as desired.
3. Move the vacuum cleaner over the surface to be cleaned, ensuring to covers all areas.
4. When finished, switch off the vacuum cleaner and disconnect it from the power source.

Removing the Dust Container and Filter
To remove the dust container and filter for cleaning or replacement:

1. Switch off the vacuum cleaner and disconnect it from the power source.
2. Open the dust container compartment and remove the dust container.
3. Carefully remove the filter from the dust container.
4. Clean or replace the filter as needed.
5. Reinsert the filter into the dust container and place it back into the vacuum cleaner.

Cleaning and Maintenance
To ensure optimal performance and longevity of the vacuum cleaner, regular cleaning and maintenance are required:

• Clean the dust container and filter after each use.
• Check for any blockages in the suction hose or brush head and remove them if necessary.
• Inspect the power cord for any damage and replace it if needed.
• Periodically clean the brush head and replace it if worn out.
• Store the vacuum cleaner in a clean and dry place when not in use.

Environmental Protection
Dispose of the product and its components by local regulations for environmental protection.

Technical Data

• Power Supply: 100-240 V (AC), 50-60 Hz
• Battery Charger Output: 18.0 V (DC), 0.5 A
• Power Consumption: 9.0 W
• Energy Efficiency: 115 V: 82.10%, 230 V: 81.81%
• Standby Power Consumption: 115 V: 0.054 W, 230 V: 0.074 W

FAQ

• Q: How long does the battery last?
  The battery life depends on the model:

  • ETA3453: Approximately 40 minutes on minimum power and 15 minutes on maximum power.
  • ETA4453: Approximately 45 minutes on minimum power and 18 minutes on maximum power.
  • ETA5453 + ETA6453 + ETA7453 + ETA8453: Approximately 50 minutes on minimum power and 20 minutes on maximum power.

• Q: What is the weight of the vacuum cleaner?
  The weight of the vacuum cleaner is approximately 260 mm x 170 mm x 1155 mm.

INSTRUCTIONS FOR USE
Dear customer, thank you for purchasing our product. Keep this instruction for use and cash receipt (if possible, including the package and its interior) for further reference.

SAFETY WARNING

GENERAL PROVISIONS:

• Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
• Check whether the data on the type label corresponds with the voltage in your socket. The power cord plug may only be connected to the electrical socket complying with the applicable standards.
• This appliance may only be used by children aged 8 years or older, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision. Children younger than 8 years must be kept out of reach of the appliance and its power cord.
• If a vacuum cleaner can be equipped with a hand–held accessory with rotating parts a warning has to be given concerning entrapment.
• Never use the appliance if its adaptor or plug is damaged, if it does not work properly, if it fell and was damaged. In this case, take the appliance to a special service to check its safety and proper function.
• Never immerse the charger, the battery and the motor part of the vacuum cleaner in water (even partially) and protect them against humidity!
• Always turn the appliance off before emptying the tank or before maintenance.
• Never leave the product unattended when in operation!
• This appliance contains batteries that may only be replaced by trained personnel.
• Do not charge the battery if the electrolyte is leaking from it.
• The appliance must be disconnected from the power adapter when removing the battery.
• Do not through the battery into fire. There is a risk of explosion!
• To ensure the safety and proper function of the appliance, use only original spare parts and accessories approved by the manufacturer.
• Only use this appliance for the purpose it was designed for, as specified in this manual. Never use the appliance for any other purpose.
• The manufacturer is not responsible for damage caused by improper use of the appliance and the accessories do not apply in situations when the safety warnings above are not complied with. Failure to replace or maintain all filters regularly according to the instructions in Chapter V., VI and also using non–original filters, the properties
  of which resulted in failure or damage of the vacuum cleaner, is also understood to be improper use of the appliance.

USE OF THE APPLIANCE:

• The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!
• The appliance may only be charged using a safe low voltage corresponding with the marking on the appliance.
• Avoid contact with the rotating brush when handling the vacuum cleaner (e.g. with loose clothes, hair, fingers, jewellery, bracelets etc.).
• Do not leave the floor nozzle with the rotating brush and the small turbo brush switched on in one place for too long! This could damage the vacuumed surface!
• The floor nozzle with the rotation brush is not intended for vacuuming impurities from carpets with high piles.
• Never use the vacuum cleaner nor touch the adaptor with wet hands or feet!
• Never use (switch on) the vacuum cleaner if it is placed in the holder and it is being charged!
• Always switch off the vacuum cleaner when charging the battery and after the vacuum cleaner is used.
• Do not vacuum wet or moist floor coverings, do not use the vacuum cleaner for outdoor areas! When moisture gets into the aggregate, there is a risk of damage and disabling it. This defect is not covered by the warranty.
• Do not vacuum water, liquid or aggressive liquid!
• Do not vacuum sharp objects (e.g. glass, shatter), hot, flammable, explosive items (e.g. ash, hot cigarette butts, gasoline, thinners and aerosol vapours) or greases (e.g. fats, oils), caustic agents (e.g. acids, solvents). Vacuuming these objects may lead to damage of the dust filters or the vacuum cleaner.
• Pores of the microfilters may be clogged when vacuuming very fine dust. Thus, air permeability will be reduced and the suction performance will drop. In this case, micro–filters have to be cleaned before the container is full. Do not use the vacuum cleaner to vacuum dirt produced during/after construction such as plasterboard dust, fine sand, cement, dust from construction, parts
  of plaster etc. If this dirt/loose construction materials/loose construction materials into the aggregate, it poses a danger of damage. The warranty repair does not cover this.

ACCESSORIES AND ASSEMBLY OF THE APPLIANCE:
Install the holder, the vacuum cleaner and the appliance within sufficient distance from flammable objects (e.g. curtains, drapes, wood, etc.), heat sources (e.g. oven, stove, etc.) and wet surfaces (e.g. sinks, wash–basins etc.).

ADAPTER:

• If the adaptor of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person to prevent dangerous situations.
• WARNING: To charge the battery, use only the network adapter supplied with this appliance.
• Use the charger in a room only.
• The adaptor supplied with this appliance is intended for this appliance only, do not use it for other purposes.
• The power cord must not be damaged with sharp or hot objects or open fire, it must not be sunk into water or bent over sharp edges.

EQUIPMENT AND ACCESSORIES

EQUIPMENT AND ACCESSORIES (Fig. 1)

• A – vacuum cleaner
  • A1 – ON/OFF button
  • A2 – operation signal lights and charging lights
  • A3 – handle
• B – dust container
  • B1 – HEPA filter
  • B2 – separator
  • B3 – container lock buttons
• C – accessories
  • C1 – crevice nozzle
  • C2 – brush
  • C3 – electric rotary brush
  • C4 – removable brush
  • C5 – removable brush arrest
  • C6 – arresting lock
• D – extension adapter
  • D1 – ON/OFF button.
  • D2 – suction power control
  • D3 – foldable part with handle
  • D4 – foldable part lock
  • D5 – vacuum cleaner lid lock button
• E – floor nozzle with rotation brush
  • E1 – floor nozzle lock button
  • E2 – removable brush
  • E3 – brush lock
  • E4 – LEDs illuminating the space in front of the vacuum cleaner
• F – mop attachment
  • F1 – universal mop pad
  • F2 – mop pad for fine cleaning
  • F3 – mop pad for dirt particles
  • F4 – filling openings
• G – charging stand
  • G1 – lower part
  • G2 – support
  • G3 – support lid lock button
  • G4 – hole for fixing on the wall
  • G5 – charging port
  • G6 – space for small accessories (crevice nozzle, brush)
• H – adapter
• I – measuring cup
• J – screws (3x)
• K – wall plugs (3x)

VACUUM CLEANER PREPARATION

Remove all packing material, and take out the vacuum cleaner and the accessories. Remove all possible adhesion foils, stick-on labels or paper from the appliance.

VACUUM CLEANER ASSEMBLY
When assembling the vacuum cleaner, follow the procedure indicated in Fig. 1, and 2. Select appropriate accessories (Fig. 8) depending on the required use (hand vacuum cleaner/stick vacuum cleaner/mop). For disassembly, proceed the other way round and release the locks.

CHARGING THE ACCUMULATOR
Turn the vacuum cleaner off before charging! Place the vacuum cleaner in the extension attachment and then in the charging base G. Connect the adaptor to the charging connector G5 and plug it into the mains. The accumulator has to be charged at least for 8 hours before the first use. After that, the standard charging time is approx. 4-6 hours. The status and progress of charging is indicated by indicator A2.

Operation signal lights and charging lights (A2)

Blinking (increase of segments)| The accumulator is charging.
Flashes| Electronic protection of the rotary brush:

1.  Rotating brush blocking at floor nozzle E – the brush will stop rotating

2.  Small turbo brush blocking – the brush stops rotating

Light on continuously| The accumulator is charged (the signal light will go out after approx. 1 minute)/indication of operation

Warning

• The vacuum cleaner can be charged only if it is placed in the extension attachment D.
• Let the vacuum cleaner recharge as soon as its suction performance is weaker.
• When using the vacuum cleaner for an extended period or in a hot environment, the accumulator might be too hot for charging. Let the accumulator cool down prior to charging.
• Remove the adaptor each time after the battery is fully charged.

OPERATING TIMES

Set power

|  | Running Time *
---|---|---
ETA3453| ETA4453| ETA5453 + ETA6453 + ETA7453 + ETA8453*
MIN| Approx. 40 min.| Approx. 45 min.| Approx. 50 min.
MAX| Approx. 15 min.| Approx. 18 min.| Approx. 20 min.
Note:** The stated operating times are based on ETA‘s internal testing and only apply to a new and fully charged battery. Depending on the age and wear of the battery, the operating time decreases.

INSTALLING THE CHARGING STAND ON THE WALL
To install the charging stand G on the wall, use the holes G4 on its back. Mount the stand G on the wall using the enclosed or other suitable connecting material.

USE OF VACUUM CLEANER

USE OF VACUUM CLEANER (Fig. 8)
Let the vacuum cleaner charge sufficiently before use.

Caution
If you use floor nozzle E or small turbo brush C3 and the rotary brush becomes blocked, switch off the vacuum cleaner, eliminate the cause of the blockage (clean the rotary brush) and then continue vacuuming.

CONTROL
ON/OFF button (A1, D1)

Suction power control (D2)

• when pressed once
• when pressed twice
  • vacuum cleaner ON/OFF switch
  • low suction power
  • high suction power

Caution

• When the vacuum cleaner is switched on, it is always at high suction power.
• The suction power may only be adjusted if the vacuum cleaner is put in the extension piece D.
• If you want to vacuum at the low suction power level and only use the handheld vacuum cleaner, first put the vacuum cleaner in the extension piece D and switch it on. Then set the low suction power, and remove the running vacuum cleaner from the extension piece D. The vacuum cleaner will then operate at low suction power level until switched off (or until the battery is discharged).

USING THE MOP ATTACHMENT (F)

1. Fill the mop attachment F with water through the filling openings F4 (max 150 ml).
2. Select an appropriate mop pad (F1, F2, F3) to suit the floor type.
3. When filled and assembled, fit the mop attachment to the floor nozzle E (Fig. 1, 4).
4. Mop the floor with smooth movements.

Notes

• The mop attachment can be used while vacuum cleaning is on or off. If you are mopping and vacuuming at the same time, first move the vacuum cleaner forward on the surface you are cleaning and then return using the same path you have already vacuumed and cleaned. This will ensure the proper sequence of the cleaning process
• vacuum cleaning to get rid of any dirt first, followed by floor mopping.
• Do not use/pour any detergent in the mop water tank.
• With the mop attachment, you can mop an area of up to 40 m2 with one fill.

REMOVING THE DUST CONTAINER AND FILTER

DUST CONTAINER REMOVAL
When taking out the dust container B follow the procedure indicated in Fig. 1. Dispose of dirt contained in the dust container with regular household waste. An emptied and cleaned container is to be put back into the vacuum cleaner in reverse order.

REPLACING THE HEPA FILTER
When removing the HEPA filter, proceed according to Fig. 1. Insert the new/clean HEPA filter into the vacuum cleaner in reverse order.

CLEANING AND MAINTENANCE

Notes

• For hygienic purposes, we recommend that you empty the container and clean the filter after each use.
• The maximum suction effect can only be achieved with a clean HEPA filter and an empty dust container.
• We recommend cleaning the HEPA filter each time when the dust container is emptied.
• When vacuuming very fine dust, the HEPA filter pores may become clogged, which reduces air permeability and the suction performance. In this case, it is required to clean the HEPA filter even when the tank is not full.

Clean the surface of the vacuum cleaner, extension attachment, charging base and adaptor with a soft wet cloth. Do not use any rough and aggressive detergents!

• Accessories
  After any vacuuming, it is recommended to check visually the brushes or collectors for possible impurities. If there are some impurities, remove them.

• Floor nozzle with rotary brush (E)
  Remove any dirt (especially hair, animal hairs, etc.) stuck to the brush. To make cleaning easier, the brush can be removed (Fig. 5).

• Electric rotary brush (C3)
  Remove any dirt (especially hair, animal hairs, etc.) stuck to the brush. To make cleaning easier, the brush can be removed (Fig. 6). ~~~~

• Mop attachment (F)
  Let any excessive water (solution) drain away from the mop attachment, e.g. to a washbasin. Rinse the attachment F under running water. The mop pads (F1, F2, F3) can be washed in a washing machine at 60 °C and dried in a tumble dryer.

• Dust container (B)
  Use a wet cloth to clean the surface of container B. Rinse the inside of the container B with water. Rinse the separator B2 under running water. Allow all the parts to dry out properly before their re-use.

• HEPA filter (B1)
  Shake out the input HEPA filter B1 gently, or blow it out. If the HEPA filter is very dirty, you can rinse it under running lukewarm water. Allow it to dry out properly.

Caution

• If you clean the HEPA filter with water, its filtration properties will deteriorate. The filter cannot be washed more than three times. After that, a new filter needs to be purchased.
• We recommend that you replace the HEPA filter twice a year.
• The HEPA filter is not suitable for washing in the dishwasher.
• Failure to clean or replace the HEPA filter as required may cause a defect of the vacuum cleaner!

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for the production of packing, components and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be received free of charge. Suitable disposal of the product can help to maintain valuable natural resources and prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. The appliance is equipped with a Li-Ion battery with a long life. For environmental protection, it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or the local waste collection site.

Removing the accumulator
You can remove the accumulators from the appliance only after they have been completely discharged (i.e. let the vacuum cleaner run until its motor stops). Unscrew the screws and open the vacuum cleaner. Gradually cut off the supply conductors and remove the accumulators (Fig. 7).

TECHNICAL DATA

• Protection class (vacuum cleaner) III.
• Accumulator (ETA3453/ETA4453/ETA5453+ETA6453/ETA7453+ETA8453) 14.4 V / 18 V / 21.6 / 25.2 V Li-Ion
• Weight (kg) approx. CCA (1.2 / 2.5)
• Size of the product (mm) (hand vacuum cleaner) 420 x 110 x 135
• Size of the product (mm) (stick vacuum cleaner) 260 x 170 x 1155
• Acoustic noise level of 83/81/80 dB(A) re 1pW (ETA8453+ETA7453/ETA6453+ETA5453/ETA4453/ETA3453)

Charging adapter| ETA3453| ETA4453| ETA5453 + ETA6453| ETA7453 + ETA8453
---|---|---|---|---
Manufacturer’s name or trademark, business registration number and address|

ETA

|

ETA

|

ETA

|

ETA

Model identifier| JOD-S-

180050GS

| JOD-S-

220050GS

| JOD-S-

270050GS

| HCX1501- 3200450E
Input voltage| 100-240 V (AC)| 100-240 V (AC)| 100-240 V (AC)| 100-240 V (AC)
Input frequency| 50-60 Hz| 50-60 Hz| 50-60 Hz| 50-60 Hz
Output voltage| 18.0 V (DC)| 22.0 V (DC)| 27.0 V (DC)| 32.0 V (DC)
Output current| 0.5 A| 0.5 A| 0.5 A| 0.45 A
Output power| 9.0 W| 11.0 W| 13.5 W| 14.4 W
Average efficiency in active mode| 115 V: 82.10 %;

230 V: 81.81 %

| 115 V: 80.95 %;

230 V: 80.91 %

| 115 V: 88.31 %;

230 V: 88.10 %

| 115 V: 87.81 %;

230 V: 87.91 %

---|---|---|---|---
Low load efficiency (10%)| –| –| 115 V: 85.76 %;

230 V: 81.41 %

| 115 V: 91.51 %;

230 V: 89.16 %

Power consumption without load| 115 V: 0.054 W

230 V: 0.074 W

| 115 V: 0.051 W

230 V: 0.068 W

| 115 V: 0.041 W

230 V: 0.068 W

| 115 V: 0.035 W

230 V: 0.043 W

Appliance protection class| II.| II.| II.| II.

• The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
• The capacity of the product battery decreases over time. Decreasing of battery capacity occurs during normal use of the appliance and is considered the usual wear and tear of the appliance. Decreasing battery capacity is not a defect of the appliance.
• Replacement of parts that require intervention in the electric part of the appliance must be carried out by a specialized service!
• WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL:

HOUSEHOLD USE ONLY; DO NOT IMMERSE IN WATER OR OTHER LIQUIDS;

• TO AVOID THE DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.
• Please read the instructions manual
• Removable power supply unit
• The symbol indicates a WARNING.

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>