LIEBHERR EKB 92 Refrigerator Integrable Built in Fridge with BioFresh Instruction Manual

LIEBHERR EKB 92 Refrigerator Integrable Built in Fridge with BioFresh

Product Information

Specifications:

• Model: EKB 92 / EKB 94 / EKB 96
• Installation Manual: https://manual-hub.com/

Installation Instructions

Please read and follow these instructions. These instructions contain Danger, Warning, and Caution notes. This information is important for safe and efficient installation and operation. Always read and comply with all Danger, Warning, and Caution notes!

Danger

Danger indicates an imminent hazard which will cause serious injury or death if precautions are not followed.

Warning

Warning indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Caution

Caution indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Important

This indicates information that is especially relevant to a problem-free installation and operation.

Note to the Installer

It is very important to follow the instructions in the manual to ensure proper installation and operation of the appliance. Before installing the appliance, be sure to thoroughly read and understand all of the information in this manual.

Warning – Risk of Electric Shock

Do not connect to the socket before the installation is completed.

Mounting the Anti-Tipping Device

Warning

To avoid a hazard due to instability of the appliance, it must be secured in accordance with the instructions.

Setting Up

Ensure proper setup of the appliance by following the steps below:

Electrical Connection

Only operate the appliance with alternating current (AC). The permissible voltage and frequency are indicated on the type plate. The position of the type plate is shown in the section entitled Description of the appliance (Operating instructions).

The socket must be properly earthed and protected by a fuse. The tripping current of the fuse must be between 10 A and 16 A.

Do not connect the appliance using an extension cable or extension socket. Do not use stand-alone inverters (conversion of direct current to alternating current/three-phase current) or energy-saving plugs. Risk of damage to the electronic control system!

Appliance Dimensions

| EKB 9271| EKB 9471| EKB 9671
---|---|---|---
Internal door panel| A = 273 mm
B = 12.5 mm
C = 658 mm| A = 337 mm
B = 12.5 mm
C = 810 mm| A = 400 mm
B = 12.5 mm
C = 962 mm
External door panel| A = 279 mm
B = 12.5 mm
C = 670 mm| A = 343 mm
B = 12.5 mm
C = 822 mm| A = 406 mm
B = 12.5 mm
C = 975 mm

Stated minimum height dimensions include when the adjustable feet are fully inserted. Width will increase by 6.5 mm when mounting strips are installed.

Installation Dimensions

Ensure proper installation dimensions by following the guidelines below:

Continuous Plinth Panel

A Recess depth for external door panel = 635 mm Recess depth for internal door panel = 635 mm plus panel thickness

B This is the point where the mains cable exits from the appliance rear. 19 mm from the left and 127 mm from the floor. Free length of the mains cable is 2.5 m.

IMPORTANT: The socket must be easily accessible so that the appliance can be disconnected from the mains quickly in an emergency. It must not be behind the back of the appliance.

FAQ

Q: What should I do before installing the appliance?

A: Thoroughly read and understand all of the information in the manual.

Q: Can I connect the appliance to the socket before installation is completed?

A: No, connecting to the socket should only be done after installation is completed.

Q: Can I use an extension cable or extension socket to connect the appliance?

A: No, do not connect the appliance using an extension cable or extension socket.

Q: Can I use stand-alone inverters or energy-saving plugs with the appliance?

A: No, using stand-alone inverters or energy-saving plugs can risk damaging the electronic control system of the appliance.

Q: How should I secure the appliance to avoid instability?

A: Follow the instructions provided for mounting the anti-tipping device.

7085 747-00

EKB 92 / EKB 94 / EKB 96

Please read and follow these instructions.

• These instructions contain Danger, Warning and Caution notes.
• This information is important for safe and efficient installation and operation.
• Always read and comply with all Danger, Warning and Caution notes!

DANGER!
Danger indicates an imminent hazard which will cause serious injury or death if precautions are not followed.

WARNING!
Warning indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION!
Caution indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

IMPORTANT
This indicates information that is especially relevant to a problem-free installation and operation.

Note to the installer
It is very important to follow the instructions in the manual to ensure proper installation and operation of the appliance.
Before installing the appliance, be sure to thoroughly read and understand all of the information in this manual.

WARNING!
Risk of electric shock.
Do not connect to the socket before the installation is completed.

Mounting the anti-tipping device

WARNING!
To avoid a hazard due to instability of the appliance, it must be secured in accordance with the instructions.

Setting up

• Do not place the appliance in direct sunlight or near cookers, radiators and similar sources of heat.
• The floor on which the appliance stands should be horizontal and level.
• Do not cover ventilation openings or grilles.
• Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m 3 per 8 g of R 600a refrigerant used in the appliance, so as to avoid the formation of inflammable gas/air mixtures in the room where the appliance is located in the event of a leak in the refrigerant circuit. The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance.

Electrical connection

• Only operate the appliance with alternating current (AC).
• The permissible voltage and frequency are indicated on the type plate. The position of the type plate is shown in the section entitled Description of the appliance (Operating instructions).
• The socket must be properly earthed and protected by a fuse.
• The tripping current of the fuse must be between 10 A and 16 A.
• Do not connect the appliance using an extension cable or exten-sion socket.
• Do not use stand-alone inverters (conversion of direct current to alternating current/three-phase current) or energy-saving plugs. Risk of damage to the electronic control system!

Appliance dimensions

Stated minimum height dimensions include when the adjustable feet are fully inserted. Width will increase by 6.5 mm when mounting strips are installed.

Door swing clearance (top view)

Dimension A and B: add panel thickness and handle projection to calculate distance to wall.

Installation dimensions

• A Recess depth for external door panel = 635 mm
  Recess depth for internal door pan-el = 635 mm plus panel thickness

• B This is the point where the mains cable exits from the appliance rear. 19 mm from the left and 127 mm from the floor. Free length of the mains cable is 2.5 m.
  IMPORTANT
  The socket must be easily accessible so that the appliance can be disconnected from the mains quickly in an emergency. It must not be behind the back of the appliance.

• C The appliance has a recess in this area for cable and water line laying.
  25 mm in depth and 140 mm in height over the whole width of the appliance.

• D This surface is visible when the appliance door is open. Designed finish is required.

Panel dimensions

Unpacking

1. Cut the straps and remove them.
2. Press in the lug, tear or cut the carton on the edge and remove it.
3. Remove all polystyrene packing material from the sides and top.
4. Remove the box with mounting accessories.
5. Remove the ventilation grille.
6. Secure the appliance door with tape to prevent it from being opened accidentally.
7. Remove the rear transportation safety components.
   Remove the packed cover strips and support strips from the appliance rear.

WARNING!
Risk of injury and damage.
Four people are required to safely remove the appliance from the bottom pallet.

8. One person tilts the appliance back-wards carefully and holds it in place.
9. Two people grasp the appliance from the bottom and lift. One on each side.
10. One person removes the pallet.
    Place the appliance carefully on the floor.

Alternative possibility

• Cut off the marked area from the pallet.

• Tilt the appliance slightly sideways.

• Slide a transport dolly between the appliance and packaging. Tie the appliance to the dolly with straps.
  Tilt the appliance onto the dolly.

• Place the appliance carefully on the floor.

Supplied accessories

Anti-tipping device

The anti-tipping device is mounted on the back wall in the recess at the finished installation height. After the appliance is in the recess and raised in height, the hook of the anti-tipping bracket will connect with the appliance top and prevent tipping.

Mounting the anti-tipping device

WARNING!

• The anti-tipping bracket must be mounted imperatively to prevent the appliance from tipping over when the fully stocked door is opened.
• Be sure that there is no plumbing or electrical wiring located in this area which could be damaged during installation.

1. Remove the anti-tipping bracket. The screws are no longer needed.

Adjustment of the anti-tipping bracket for use in a 635 mm deep recess

Both base parts of the anti-tipping bracket must be adjusted for use in a recess with a depth of 635 mm.

• Loosen the screws.
• Move the base part back or forth.
• Tighten the screws.

If the recess is deeper than 635 mm, a spacer must be mounted between anti- tipping bracket and wall.

Safety instructions and warnings for water connection

• Do not install the water connection while the appliance is connected to an electrical socket.
• The connection to the mains water supply may only be made by a trained and licensed plumber.

WARNING!
Connect to potable water supply only.

Water connection requirements

• The water pressure must be in the range of 0.28-0.62 MPa (2.8-6.2 bar).
• Failure to meet these requirements may result in water dis-penser malfunction and a water leak that can damage flooring and surrounding furniture.
• A shut-off valve must be installed between the water line and the mains water supply. It must be easily accessible so that the water supply can be stopped immediately if necessary.
  IMPORTANT
  Do not install the shut-off valve behind the appliance.

Models EKB 9471 and EKB 9671 only
The water supply to the appliance must be through a cold water pipe that can withstand the operating pressure and complies with the hygiene regulations. For this, use the stainless steel hose supplied (length 3 m).

IMPORTANT
Do not use any old or already premounted water supply lines.

Appliance installation

Move the appliance towards the final position and leave enough space to work behind.

Models EKB 9471 and EKB 9671 only

Models EKB 9471 and EKB 9671 only

IMPORTANT
Make sure that the connection is fitted with a seal and is tight.

Models EKB 9471 and EKB 9671 only

Models EKB 9471 and EKB 9671 only

• Insert the water filter as far as it will go with the front knobs in a horizontal position and turn clockwise until it snaps in.

• Route the mains cable towards the socket.

• Route the water hose towards the water shut-off valve.
  IMPORTANT Complete the installation before switching on the appliance.

• Remove the tapes.
  Open the door and re-move the transportation safety component.

• Remove the mounting strip from the attachment bracket, turn 180° and insert into the attachment bracket as far as it will go.

• Apply the appliance cover strips to the left and right front edge of the appli-ance housing, align in height with the appliance top and screw into place. The strip is transparent so that the designed attachment holes on the appliance hous-ing are visible.
  IMPORTANT
  Use the correct flat-headed screws, otherwise the edges of the kitchen unit will be damaged when sliding the appliance into the recess.

• Mounting the depth adjustment aid into the cover strips

• Slide the appliance into the recess. To avoid damage, move the mains cable and the water line at once.

• Remove the transportation safety components using the Torx 25 key.

DANGER!
Risk of death or serious injury due to appliance tipping.
Do not open the appliance door before the height adjustment is finished and the anti-tipping bracket supports the appliance.

IMPORTANT
When turning the screws with an electric screwdriver, please make absolutely sure that:

• Maximum rotation speed = 400 rpm
• Maximum torque = 1 Nm

Failure to follow this instruction will result in damage to the height adjustment.

Push the mounting strip upwards.
The bottom edge of the mounting strip must be aligned with the top edge of the adjacent unit door.

Internal door panel

Open the door.
Unscrew the attachment bracket with the mounting strip. To do so, use the ring spanner provided.

Position the attachment bracket in the middle of the door panel, align horizontally and secure to the door panel using eight 4 x 14 screws.

IMPORTANT
Door handles should be mounted now because the panel support strips will cover the mounting holes.

Position the panel support strips with the top lug in the cut-out of the top attachment bracket. Align the strips parallel to the side edge of the panel and screw into place with ten 4 x 14 screws.

IMPORTANT
If the door has to be limited to a 90° opening angle, it must be done before the panel is mounted onto the appliance door. See chapter “Important note for changing over door hinges or limiting the door opening angle to 90°” on page 37.

Open the appliance door.
Place the door panel on the top adjusting screws and align in the centre.
Screw the hex nuts onto the adjusting bolts and tighten.
Use the 10 mm spanner provided.

Close the door and check the position of the door panel.

IMPORTANT
After a certain time and loading, it may be necessary to readjust the door.

• Align the panel in its vertical posi-tion if necessary.

• Loosen the hex nuts and turn the adusting bolts with the Torx 15 key provided.

• Align the panel horizontally with the long slots in the at-tachment bracket.

• Tighten the hex nuts. Use the 10 mm spanner pro-vided.

• Align the panel in its depth.

• Loosen the screws, align the panel and tighten the screws.

• Align the panel in its depth at the bottom.

• Loosen the screws, align the panel and tighten the screws. Use the Torx 20 key provided.

• Secure the panel through the bottom attachment bracket with two 4 x 14 screws.

• Insert the panel supports between panel and appliance door and screw into place with two M6 x 12 screws each.

• Hook the door cover strips to the front of the supports and snap in at the back.

• Click cover into place.

• Insert the door racks.
  The bottle rack must be in the lowest possible position of the clip-in strip.

• Insert the hooks of the rack into the open-ings of the clip-in strip at the desired height and push down.
  IMPORTANT Be sure each door rack is fixed properly in the clip-in strip.

Please note in case of removing appliance from the recess
If the appliance has to be removed from the recess again, please make sure you take account of the following:

1. Remove the door panel.

2. Lower the appliance using the height adjustment unit.

3. Mount the transportation safety components with two screws for each support using a Torx 25 key.

DANGER!
Risk of death or serious injury due to the appliance tipping over.
Do not remove the appliance without the mounted transportation safety components.

Important note for changing over door hinges or limiting the door opening angle to 90°

• Changing the door hinges or limiting the door opening angle to 90° should only be carried out by a trained expert.
• The door hinges are fitted with strong closing springs. If the hinge accidentally snaps shut, this can lead to serious injury.
• The door itself is very heavy. Do not try to remove the door yourself.
• Contact the Liebherr customer service department for more information. See contact details on the back of this manual.

Liebherr Hausgeräte Lienz GmbH Dr.-Hans-Liebherr-Strasse 1
A-9900 Lienz
Österreich
www.liebherr.com

References

• Manual-Hub.com - Free PDF manuals!
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>