NOYAFA NF-8506 Ethernet Cable Tester Instructions
- June 16, 2024
- NOYAFA
Table of Contents
NOYAFA NF-8506 Ethernet Cable Tester Instructions
Please read the manual carefully before operating this unit.
- Both Transmitter and Receiver were powered by Lithium Battery.
- Don’t put the device in dusty, wet or hot (above 40°C) place.
- Don’t disassemble, maintenance the device without profession knowledge.
- Pls get out the batteries for.
- Pls don’t use the device for telecommunication in thunderstorm to keep safe.
Instruction for Keys and Ports
Main Function: Continuity Test; Cable Tracking: Port Flash; Cable Length
Measurement; PoE Test; Ping Test; IP Scan; Switch Test; Set.
Instruction for Ul icons
AUTO-OFF: Customers can see the icon ” ” on the left top of the screen when
the function is ON, Customers can choose to turn it off in “Set”.
Power Level: Show the battery power level of the device, it will turn to
Green when charging, and stays white when in use.
Cable Continuity Test
Port Flash
PoE Test
IP Scan
Set
Cable Tracking
Cable Length Measurement
Ping Test
Switch Test
Instruction for functions
Cable Continuity Test
Modes: Remote and Switch.
Remote: Can test cable continuity, Cross/ Short Condition.
Switch: Can only test cable continuity.
Take remote mode as an example.
Insert one end of the cable into the “CONT” Port on the transmitter and the
other end into the Port on the receiver, Choose “Remote” mode, turn to “Start”
then press “to test. Testing result as following:
Good
Cable Cross
Short Circuit
Cable Open
Cable Tracking
Two Modes: Digital Mode / Analog Mode, Customers can use UP/Down to switch.
Digital Mode: Anti-interference, when tracking cables with load from 1000M switches, customers were suggested use this mode.
Analog Mode: With little noise, customers were suggested to use this mode when tracking cables without load.
Transmitter:
Default set to Digital mode, use UP/Down button to switch between the two
modes.
Receiver:
If the scan signal indicator stays on, it means the receiver is in Digital
mode;
If the scan signal indicator blinks, it means the receiver is in Analog mode.
Digital Mode
Remarks:
The transmitter should stays the same mode with the receiver, otherwise the receiver won’t be able to receive the signal.
The signal sensitivity switch was used to adjust the sensitivity of the receiver, the max detect depth range is 10cm, with 600m length without load and 1000m with load.
The indicator on the receiver will turn into purple once it detect signal, the
stronger the signal is, the darker the purple will be.
Port Flash
After connecting the device with the switch, the green dot on the screen will flash at the same frequency as the port indicator on the switch.
Port Flash
Cable Length Measurement
Insert one end to the Length port of the device (Keep the other end empty), Choose the right type of the cable (CAT5/ CAT6), Set the unit for the result (Meter/ Yard/Feet) by pressing “x”, then press ox “to measure the cable length (Best range will be 5~200m), the result will be displayed in pin pairs.
When measuring broken cables, if the broken point is too close to the empty
end (less than 3% of the full length), due to technical reason, the device
will show the full length of the cable, in that case customers were suggested
to measure the length from the other end to locate the broken point.
PoE Test
Connect device and PoE switch, press “OK” to enter PoE test function, the result will show which pins are providing power:
The voltage of the power; Standard of PoE switch (IEEE 802.3at/af/bt); Class
of the power (Class 1~8); Power supply type (Mid span/ End Span/ AT-4 pairs).
Ping Test
Customers were suggested to set IPV4 for the first time to use Ping test function, after entering the Ping address, customers can use UP/Down button to choose “Set IP” to set the local IP, Subnet Mask, and Gateway, after setting these, customers need to save the settings then can return to use the Ping scan functions.
Ping Test
Set IP
IP Scan
Using UP/Down button to choose “Set IP” to set the local IP, Sub net Mask, and Gateway, after setting these, customers need to save the settings then can return to use the IP scan functions.
Switch Test
After testing, the testing result will show the standard of the switch
(10M/100M/ 1000M) and also the duplex mode of the switch.
PS: After testing, customers need to reprocess the whole steps for new port testing to ensure the accuracy of the testing.
Set
Customers can set, back light level, back light time, auto off, default setting, check inf about the device etc.
Product Specification
| Model | NF-8506 |
|---|---|
| Cable Scan | Digital Mode / Analog Mode |
| Auto OFF | |
| Low Power Notice | |
| Transmitter | Cable Continuity Test |
| Cable Length Test | Range: 5-200m (±3m) |
| Port Flash | 10M/100M/1000M |
| POE | Mid-Span/End-Span/AT-4 pairs |
| Link Speed | PoE voltage test |
| Battery | 10M/100M/1000M |
| Ping Scan Function | Duplex Mode (Full Duplex/ Half Duplex) |
| IP Scan Function | 3.7V Lithium Battery |
| Transmitter Dimension | 150×75×35mm |
| Receiver | Ear Phone |
| Battery | 3.7V Lithium Battery |
| Receiver Dimension | 200×50×33mm |
Packing List
| Transmitter | 1pc | Tool Bag | 1pc |
|---|---|---|---|
| Receiver | 1pc | Packing Box | 1pc |
| User Manual | 1pc | Warranty Card | 1pc |
| Lithium Battery Notification Card | 1pc | Recharging Cable | 1pc |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>