Microsemi PD-9001GC 1 Port 802 3at Gigabit Midspan User Guide
- June 16, 2024
- Microsemi
Table of Contents
- Microsemi PD-9001GC 1 Port 802 3at Gigabit Midspan
- Product Information
- Safety Information
- Preliminary Steps
- FAQ
- Functions and Features
- Important Safety Information
- Preliminary Steps
- Installing the Unit
- Ethernet Interface
- Indicators
- Specifications
- Troubleshooting
- Recycling and Disposal
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Microsemi PD-9001GC 1 Port 802 3at Gigabit Midspan
Product Information
Specifications
- Product Name: Microsemi PD-9001GC
- Model Number: POE130-AT
- Port: 1-port
- Power Output: Guaranteed 30W
- Compliance: IEEE802.3at
- Input Voltage: Universal AC input 100-240VAC
- Data Rates: 10/100/1000mbps pass-through
Functions and Features
The Microsemi PD-9001GC is a 1-port 802.3at Gigabit Midspan with the following main features:
- Provides PoE output
- Guaranteed power output of 30W
- Compliant with IEEE802.3at standards
- Compact dimensions for easy installation
- Supports universal AC input voltage range of 100-240VAC
- Data rates of 10/100/1000mbps pass-through
Safety Information
Before using the PD-9001GC, please consider the following important safety information:
- This injector should only be connected to PoE networks and should not be routed to outside plant.
- The Ethernet and Terminal ports are shielded RJ45 data sockets and cannot be used as POTS sockets.
- The Ethernet and Terminal interfaces are qualified as SELV circuits and can only be connected to SELV interfaces on other equipment.
- Ensure the power cord is a three-conductor type with proper grounding and rated for a minimum of 250Vac RMS operation.
- Do not connect the PD-9001GC to a power outlet if the voltage indicated on the label is different from the outlet voltage.
- Do not use a cross-over cable between the PD-9001GC output port and the load device.
Preliminary Steps
Before connecting and using the PD-9001GC, please follow these steps:
- Read the installation instructions provided in the user manual.
- Plug the PD-9001GC into an AC power source. There is no on/off switch.
- Verify that a PoE Ready Ethernet-compatible device is connected.
- Avoid covering the PD-9001GC or blocking airflow with foreign objects. Keep it away from excessive heat, humidity, vibration, and dust.
- Ensure that the cable length from the Ethernet network source to the terminal does not exceed 100 meters (330 feet). The PD-9001GC is not a repeater and does not amplify Ethernet data signal.
- If desired, use a splitter, but ensure that it is connected close to the terminal and not on the PD-9001GC.
EMC Compliance
The PD-9001GC is compliant with the following EMC standards:
- FCC Part 15 class B
- EN55032 class B
- EN55024
- VCCI
Technical Support
If you encounter any problems during installation or usage, please consult the Microsemi website at http://www.Microsemi.com. You can also contact technical support through the following channels:
- USA/Canada: +1-949-380-6245
- Email: POEsupport@microsemi.com
FAQ
Can I use the PD-9001GC with any IP device?
No, the PD-9001GC should only be connected to an IP device it was bought with. Using it with other IP devices can cause damage.
What safety precautions should I take when connecting the PD-9001GC to its power source?
Follow basic electricity safety measures and ensure there is no voltage mismatch. If the voltage on the label is different from the power outlet voltage, do not connect the PD-9001GC to that outlet.
Can I use a cross-over cable between the PD-9001GC output port and the load device?
No, a cross-over cable should not be used. Use a regular Ethernet cable for proper connection.
Functions and Features
The PD-9001GC is a Power over Ethernet (PoE) Single Port Midspan/Injector that
offers a super compact
and cost-effective power solution for WLAN access points, network cameras, and
other IP terminal installations. The PD-9001GC Power over Ethernet (PoE)
Midspan/Injector is IEEE802.3at compliant, it adds 55V DC to wires 4,5,7,8 of
a standard Ethernet cable in category 5 and above and enables delivery of both
data and power to the IP terminal.
The PD-9001GC can be powered via universal AC input and can provide up to 30
Watts.
Main Features:
- 1-port PoE output
- Guaranteed 30W
- IEEE802.3at compliant
- Super small dimensions
- Universal AC input 100-240VAC
- 10/100/1000mbps pass-through data rates
Notice
It is Microsemi’s policy to improve its products as new technology, components, software, and firmware become available. Microsemi, therefore, reserves the right to change specifications without prior notice.
Important Safety Information
- This injector should be connected to PoE networks only, without routing to outside plant.
- The PD-9001GC Ethernet and Terminal ports are shielded RJ45 data sockets. They can’t be used as Plain Old Telephone Service (POTS) sockets. Only RJ45 data connectors can be connected to these sockets.
- The PD-9001GC Ethernet and Terminal interfaces are qualified as Safety Extra-Low Voltage (SELV) circuits according to IEC 60950-1. These interfaces can only be connected to SELV interfaces on other equipment.
- The power cord must be a three-conductor type (two current carrying conductors; one ground conductor) terminated on one end by an IEC 60320 appliance coupler (for connection to the PoE Media Converter), and on the other end by a plug containing a ground (earth) contact.
- The power cord must be rated for a minimum of 250Vac RMS operation, with a minimum rated current capacity of 5 amps (or a minimum wire gauge of 18 AWG (0.823mm2).
WARNINGS!
- This Midspan should only be connected to an IP device with which it was bought. Using PD-9001GC with other IP devices can cause damage to IP device.
- Follow basic electricity safety measures whenever connecting PD-9001GC to its power source.
- A voltage mismatch can cause equipment damage and may pose a fire hazard. If the voltage indicated on the label is different from the power outlet voltage, do not connect PD-9001GC to this power outlet.
- Do not use a cross-over cable between the PD-9001GC output port and the load device.
Preliminary Steps
- Read installation instructions before connecting the PD-9001GC to its power source.
- There is no “on/off” switch; simply plug the PD-9001GC into an AC power source.
- Verify that a PoE Ready Ethernet-compatible device is connected.
- Do not cover PD-9001GC or block airflow to the unit with any foreign objects. Keep PD-9001GC away from excessive heat and humidity and free from vibration and dust.
- Ensure cable length from the Ethernet network source to terminal does not exceed 100 meters (330 feet). This Midspan is not a repeater and does not amplify the Ethernet data signal.
- Use a splitter if desired; ensure the splitter is connected close to the terminal and not on the PD-9001GC!
PD-9001GC EMC Compliance:
- FCC Part 15 class B and EN55032 class B
- EN55024
- VCCI
PD-9001GC Safety Compliance:
- UL/cUL per 60950-1
- GS Mark
Installing the Unit
- Connect the PD-9001GC to an AC outlet (100-240VAC).
- Connect the “DATA IN” jack (input) to the remote Ethernet network switch’s Patch panel.
- Connect the “PWR OUT” jack (output) to Terminal.
Ethernet Interface
Indicators
Port LED | Indicated Behavior |
---|---|
Yellow On | Power is on (power is active) |
Green On | A remote terminal is connected |
Green Blinking | Overload state or short-circuit |
Specifications
Environmental Specifications
Mode | Temperature | Humidity |
---|---|---|
Operating | -10 to 40°C |
14 to 104°F
| 5 to 95% (non-condensing)
Storage| -20 to 70°C
-4 to 158°F
| 5 to 95% (non-condensing)
Electrical Specifications
Input Voltage | 100-240 VAC (50/60Hz) |
---|---|
Maximal Input Current | 1 Ampere |
Available Output Power | 30 Watts |
Nominal Output Voltage | 55 VDC |
Physical Specifications
Unit weight | 170 gr |
---|---|
Dimensions (W x H x L) | 46 x 32 x 141 mm |
Troubleshooting
Symptom | Corrective Steps |
---|
PD-9001GC
Midspan does not power up
| 1. Verify that an approved power cord is used.
2. Verify that the voltage at the power inlet is between 100 and 240VAC.
3. Remove and re-apply power to the device and check the indicators during power up sequence.
The Powered Device (PD) doesn’t operate
| 1. Verify that the PD is designed for PoE operation according to IEEE802.3at standard.
2. Verify that you are using a standard straight-wired four-pair cable (UTP/FTP Category 5/5e/6).
3. Verify that the PD is connected to the PD-9001GC “Terminal” port.
4. If an external power splitter is in use, replace it with a known-good splitter.
5. Remove and re-apply power to the Midspan.
The end device operates, but there is no data link
| 1. Verify that you are using a standard straight-wired four-pair cable (UTP/FTP Category 5/5e/6).
2. Verify that the Ethernet cable length is less than 100 meters from Ethernet source to load/remote terminal.
3. Ensure that the input Ethernet cable is connected to the power injector’s “Ethernet” port.
4. If an external power splitter is in use, replace it with a splitter known to be good.
Recycling and Disposal
Disposal instructions for old products. The WEEE (Waste Electrical and
Electronic Equipment) national environmental initiatives has been put in place
to ensure that products are recycled using best available treatment, recovery
and recycling techniques to ensure human health and high environmental
protection. Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused. Do not dispose of
your old product in your general household waste bin. Inform yourself about
the local separate collection system for electrical and electronic products
marked by this symbol:
Use one of the following disposal options:
- Dispose of the complete product (including its cables, plugs, and accessories) in the designated WEEE collection facilities.
- If you purchase a replacement product, hand your complete old product back to the retailer. He should accept it as required by the national WEEE legislation.
Ordering information:
- Product Name: PD-9001GC
- Part Number: PD-9001GC/AC
- Description: 1-Port 30 Watts Midspan
© 2017 Microsemi Corporation. Document P/N: 06-7124-160 REV A00
References
- Manual-Hub.com - Free PDF manuals!
- Microsemi | Semiconductor & System Solutions | Power Matters
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>