Panasonic SB-AFC500 Speaker System Instruction Manual

: June 16, 2024
: Panasonic

Table of Contents

Panasonic SB-AFC500 Speaker System
Product Information
Product Usage Instructions
Speaker System
Supplied accessories
Care
Speaker set-up
Location
Connections
Speaker impedance and allowed input
Protection circuitry
Excessive input
Other notes
Maintenance
Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Panasonic SB-AFC500 Speaker System

Product Information

Specifications

Model: SB-PF500 / SB-AFC500
Supplied Accessories:
- Metal wall mount kit (RFA1881) – 1
- Metal wall mounts – 2 per kit
- Screws – 4 per kit
- Speaker feet – 1 sheet (4 feet) (RFA0631A-K)

Product Usage Instructions

Speaker Set-up
The two speakers provided are the same and can be used as front speakers. We recommend using them as front speakers for optimum performance.

The role of the speaker is determined by how you connect and place it. We recommend using it as a center or surround speaker.

Attaching Rubber Feet to the Speaker
The speaker can be set up either standing or lying down. To prevent vibration causing the speaker to move or fall over, attach the rubber feet provided to the four corners of the speaker. Make sure to turn the logo so it is horizontal.

Attaching the Speaker to the Wall

If you prefer to hang the speaker on the wall, follow these steps:

Attach the rubber feet to the four corners of the speaker.
Use screws (not included) that are at least 35 mm (1-3/8 inches) long to attach the metal wall mounts (included) to the wall.
Hang the speaker on the metal wall mounts.
Note: The placement of the speaker on the wall can affect the bass output.

Speaker Connection
Refer to the illustration below for examples of speaker connection:

Location and Placement
When deciding on the location and placement of the speakers, consider the following:

Place the speakers away from the edges and corners to avoid injury if knocked or if the speaker falls over.
Ensure there is enough space for proper ventilation and avoid blocking the bass reflex ports located at the rear of the speakers.
Do not attempt to attach the speakers to walls using methods other than those described in this manual.

FAQ

Q: Where can I find the model and serial number of the product?
A: The model number and serial number can be found on either the back or the bottom of the unit.
Q: How can I order replacement parts or accessories?
A: To order accessories, you can contact 1-800-332-5368 or visit the website http://www.panasonic.com.

Speaker System

Operating Instructions

Model No
SB-PF500
SB-AFC500

Before connecting, operating or adjusting this product, please read these instructions completely.
Please keep this manual for future reference.

Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully.

Floor speakers X 2	SB- PF500
Multi-use speaker	SB- AFC500

User memo

DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBERDATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER

The model number and serial number of this product can be found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for future reference.

MODEL NUMBER SB-PF500
SERIAL NUMBER B-AFC500

Supplied accessories

Please check and identify the supplied accessories.
Use numbers indicated in parentheses when asking for replacement parts.
(Only for U.S.A.)
To order accessories contact 1-800-332-5368 or web site (http://www.panasonic.com).

Multi-use speaker SB-AFC500 only

Care

These speakers have sharp edges and corners.
Take care when moving them.
Locate them so that they will not be knocked.
The speaker’s edges and corners can cause injury if you knock them or the speaker falls over.

Speaker set-up

SB-PF500

The two speakers are the same.
We recommend using them as front speakers.

SB-AFC500

How you connect and place this speaker determines its role.
We recommend using it as a center or surround speaker.

Attach the rubber feet to the speaker SB-AFC500

The speaker can be set-up either standing or lying down. Attach these rubber feet to prevent vibration causing the speaker to move or fall over.
(See below if you would prefer to hang the speaker on the wall.)

One sheet of 4 rubber feet is included.

Rubber feet (4 per speaker, included)
Cloth (not included)
Turn the logo so it is horizontal.

Attaching the speaker to the wall SB-AFC500

Attach the rubber feet to the four corners.

Screws (not included) 35 mm (1-3/8w) or longer Screws (4 per speaker, included)
Metal wall mounts (2 per speaker, included)

Note

Screw the wood screw into a thick and hard part of the wall. The surface you attach the speaker to must be able to support over 30 kg (66 lb.).
Use wall strengtheners and screws that can adequately bear the weight of the multi-use speaker. Seek advice from a qualified per-son.
Do not attach horizontally.
As this speaker has a bass reflex port on the rear, attaching it to a wall can affect bass output.

Speaker set-up

The illustration shows examples of connection.

Front speaker (Left)
Center speaker SB-AFC500
Receiver or amplifier (not included)
Front speaker (Right) SB-AFC500
Surround speaker (Right) SB-AFC500
Surround speaker (Left) SB-AFC500
Speaker cables (not included) SB-PF500

Location

The front, center, and surround speakers should be placed at approximately the same distance from the listening position. The angles in the diagram are approximate.
Positioning for best effect How you set up your speakers can affect the bass and the sound field. Note the following points.

Place speakers on flat, secure bases.
Placing speakers too close to floors, walls, and corners can result in excessive bass.
Cover walls and windows with thick curtain.
Place the surround speakers on the side of or slightly behind the seating position, about one meter higher than ear level.
Vibration may cause distortion in the picture if the center speaker is placed directly on the television. Place it on a rack or shelf.
Place the speakers at least 5 cm (2w) from the wall as they have bass reflex ports in the rear.

Caution
Do not attempt to attach these speakers to walls using methods other than those described in this manual.

Connections

Confirm the colors of the cords to ensure correct connection. Incorrect connection can damage the unit.

Before making the connections, switch OFF the power to the amplifier.
Use with an amplifier having 6 Ω impedance for these speakers.
Be sure to connect only positive (+) wires to positive (+) terminals, and negative (–) wires to negative (–) terminals.

Connecting the cables

Before connection
Strip the outer covering from the end of the cable to a length of approximately 15 mm (19/32w) and twist the center wire.

If using a commercially available 4-mm plug cable
Fully tighten the speaker terminal knob, and then insert the end of the plug cable into the top of the knob.

Caution
To prevent damage to circuitry, never short-circuit positive (+) and negative (–) speaker wires.

Notes

Speaker impedance and allowed input

Impedance	6 W
Input power	100 W (DIN)

Caution
The only receivers or amplifiers you should connect to these speakers are those whose rated output does not exceed the above figures.
Using a receiver or amplifier with higher ratings than listed above can cause abnormal sounds to occur because of excessive input, damage to the receiver or speakers, and fire. If equipment is damaged in any way or unexpected trouble occurs during playback, unplug the system from its outlet and call a servicenter for assistance.

Protection circuitry

These units incorporate protection circuitry to protect them from damage caused by excessive input or abnormal signals; when excess input is detected, input is automatically interrupted.

If sound is interrupted.

Reduce the volume of the receiver (or amplifier).
Check the sound source and connections for any problems. If there is no problem, the protection circuitry will reset in a few minutes.

After the protection circuit is reset…
Take care not to increase the receiver’s volume too high.

Excessive input

You can damage your speakers and shorten their useful life if you play sound at high levels over extended periods.
Reduce the volume in the following cases to avoid damage :

When playing distorted sound.
When the speakers are receiving howling from a microphone or record player, noise from FM broadcasts, or continuous signals from an oscillator, test disc, or electronic instrument.
When adjusting the sound quality.
When turning the amplifier on or off.

Other notes

If irregular coloring occurs on your television
These speakers are designed to be used close to a television, but the picture may be affected with some televisions and set-up combinations.
If this occurs, turn the television off for about 30 minutes. The television’s demagnetizing function should correct the problem. If it persists, move the speakers further away from the television.
Do not touch the diaphragms.
Doing so might cause distortion.
Keep magnetized items away.
Magnetized cards, bank cards, commuter passes, etc., can be damaged if allowed too near speaker magnets. Clocks may also be affected.

Avoid locations such as described below :

In direct sunlight
Near heating appliances or other sources of heat
Where the humidity is high

Maintenance

Clean these units with a soft, clean, dry cloth.
Clean regularly to maintain the polished surface.

Never use alcohol, paint thinner, or benzene to clean these units.
Before using chemically treated cloth, read the instructions that came with the cloth carefully.

Product service

Damage requiring service—The unit should be serviced by qualified service personnel if:
- Objects or liquids have gotten into the unit; or
- The unit has been exposed to rain; or
- The unit does not operate normally or exhibits a marked change in performance; or
- The unit has been dropped, or the cabinet damaged.
Servicing—Do not attempt to service the unit beyond that described in these operating instructions. Refer all other servic-ing to authorized servicing personnel.
Replacement parts—When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other hazards.
Safety check—After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working condition.

Product information
For product information or assistance with product operation;

In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or e-mail consumerproducts@panasonic.com, or web site (http://www.panasonic.com).
In Canada, contact Panasonic Canada Inc. Customer Care Centre at 905-624-5505, web site (www.panasonic.ca), or an authorized Servicentre closest to you.

Specifications

Floor speakers SB-PF500
Type 3 way 5 speaker system Bass-reflex type
Speaker (s)
Woofer : 8 cm (3-1/8w) cone type x 4
Tweeter: 2.5 cm (1w) dome type x 1
Impedance 6 Ω
Input power 200 W (Music), 100 W (DIN)
Sound pressure level 83 dB/W (1.0 m)
Crossover frequency 1.8 kHz, 2.5 kHz
Frequency range 45 Hz – 50 kHz (at –16 dB)
50 Hz – 40 kHz (at –10 dB)
Dimensions (W x H x D) 250 x 1092 x 280 mm
(9-27/32w x 43w x 11w)
Mass 11.8 kg (26.0 lb.)

Multi-use speaker SB-PF500
Type 2 way 3 speaker system Bass-reflex type
Speaker (s)
Woofer: 8 cm (3-1/8w) cone type x 2
Tweeter: 2.5 cm (1w) dome type x 1

Impedance 6 Ω
Input power 200 W (Music), 100 W (DIN)
Sound pressure level 81 dB/W (1.0 m)
Crossover frequency 2.5 kHz
Frequency range 56 Hz – 50 kHz (at –16 dB) 63 Hz – 40 kHz (at –10 dB)
Dimensions (W x H x D) 116 x 380 x 207 mm (4-9/16w x 15w x 8-5/32w)
Mass 4.6 kg (10.1 lb.)

Note

Specifications are subject to change without notice.
Mass and dimensions are approximate.

Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus,
New Jersey 07094
http://www.panasonic.com

2001 Matsushita Electric Industrial Co., Ltd.
Printed in Malaysia / Imprimé en Malaisie