WORX WR167E Landroid Robot Mower Owner’s Manual
- June 16, 2024
- Worx
Table of Contents
WR167E Landroid Robot Mower
Specifications
- Model Numbers: WR147E.1, WR148E, WR165E, WR167E
- Website: https://manual-hub.com/
Product Information
Welcome to Worx Landroid Robot Mower! This fully autonomous and
configurable mower is designed to give you the best lawn ever. With
its agility and efficiency, Landroid will manicure your grass
effortlessly. This manual will guide you through the setup
process.
Product Usage Instructions
Safety First
Before using the product, it is important to follow these safety
instructions:
-
For machines used in public areas, warning signs must be placed
around the working area to notify people of the automatic
lawnmower. The signs should say: “WARNING! Automatic lawnmower!
Keep away from the machine! Supervise children!” -
When the mower is turned upside down, always switch off the
power key and remove the battery. -
When working on the mower’s under frame, such as cleaning or
replacing blades, switch off the power key and remove the
battery. -
Connect Landroid and its peripherals only to a supply circuit
protected by a residual current device (RCD) with a tripping
current of not more than 30mA. -
Wear protective gloves when replacing blades to avoid
injuries. -
To stop the mower, press the STOP button.
-
When starting the mower for the first time, select a four-digit
PIN code. -
Always switch off the robotic lawnmower before carrying
it. -
When carrying the mower, hold it by the handle at the rear,
under the mower, with the blade disc away from the body. -
To meet RF exposure requirements, maintain a separation
distance of 200mm or more between the device and people during
operation. Operations closer than this distance are not
recommended. -
The antenna used for this transmitter must not be co-located
with any other antenna or transmitter.
Information on Landroid
Here are some important details about Landroid:
-
Keep a safe distance from the machine when operating it.
-
Do not ride on the machine.
-
The product contains a Li-Ion battery that should be properly
disposed of to reduce environmental impact. Do not burn the battery
or dispose of it as unsorted municipal waste. -
Do not disassemble the machine without authorization.
-
Waste electrical products should not be disposed of with
household waste. Please recycle them where facilities exist. Check
with your local authorities or retailer for recycling advice.
FAQ
Q: Where can I find support for Worx Landroid?
A: You can find support at www.worx-europe.com/support.
Q: Is there an owner’s site for Landroid?
A: Yes, you can visit the Landroid Owner’s Site at https://account.worxlandroid.com/login.
Q: How can I contact customer services?
A: You can reach customer services by calling 0345 202 9679.
Owner’s manual
Original instruction
WR147E.1 WR148E WR165E WR167E
Table of contents
TABLE OF CONTENTS
p. 03
p. 04
p. 08 p. 09 p. 10
p. 12 p. 15 p. 20 p. 23 p. 24
p. 25 p. 26 p. 27 p. 27 p. 27
p. 29 p. 30 p. 33 p. 37 p. 38 p. 39
Welcome Contact information Safety first Important safety instructions Get familiar with Landroid What’s in the box Getting to know Landroid How Landroid works Getting started Planning Installation Starting Landroid Connecting Landroid to the Internet Using the App Maintenance Keep it sharp Keep it clean Keep it charged Keep it stored over the Winter Keep it updated Quick reference Operation messages Error messages Trouble shooting Technical data Noise data and accessories Declaration of conformity
EN
2
Welcome
EN
Thank you for purchasing a Worx Landroid Robot Mower. Totally autonomous, fully configurable, agile and efficient, Landroid manicures your grass and gives you the best lawn ever. This manual will help you get set up.
We’re here to help:
Support www.worx-europe.com/support
Landroid Owner’s Site https://account.worxlandroid.com/login
Customer Services Helpline 0345 202 9679
3
Safety first
EN
PRODUCT SAFETY GENERAL & ADDITIONAL SAFETY INSTRUSCTIONS
WARNING: Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious
injury. Carefully read the instructions for the safe operation of the machine.
Save all warnings and instructions for future reference. · This appliance is
not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their
safety. · Children should be supervised to ensure that they do not play with
the appliance. · This appliance contains batteries that are only replaceable
by skilled persons. WARNING: For the purposes of recharging the battery, only
use the detachable supply unit provided with this appliance. WARNING: To
reduce the risk of injury to persons and damage to the machine, do not remove
battery pack before switching off the machine.
IMPORTANT READ CAREFULLY BEFORE USE – KEEP FOR FUTURE REFERENCE
Safe operation practices Training · Read the instructions carefully. Make sure
you understand the instructions and be familiar with the controls and the
proper use of the
appliance. · Never allow people unfamiliar with these instructions or children
to use the appliance. Local regulations can restrict the age of the
operator. · The operator or user is responsible for accidents or hazards
occurring to other people or their property.
Preparation · Ensure the correct installation of boundary wire as instructed.
· Periodically inspect the area where the appliance is to be used and remove
all stones, sticks, wires, bones, and other foreign objects. · Periodically
visually inspect to see that the blades, blade bolts and cutter assembly are
not worn or damaged. Replace worn or
damaged blades and bolts in sets to preserve balance. · On multi-spindle
appliances, take care as rotating one blade can cause other blades to rotate.
WARNING! The lawnmower should not be operated without the guard in place
OPERATION
1. General · Never operate the appliance with defective guards, or without
safety devices, for example deflectors, in place. · Do not put hands or feet
near or under rotating parts. Keep clear of the discharge opening at all
times. · Never pick up or carry an appliance while the motor is running. ·
Operate the disabling device from the appliance.
– Before clearing a blockage – Before checking, cleaning or working on the
appliance · It is not permitted to modify the original design of robotic
lawnmower. All modifications are made at your own risk. · Start robotic
lawnmower according to the instructions. When the power key is switched on,
make sure you keep your hands and feet away from the rotating blades. Never
put your hands and feet under the mower. · Never lift up robotic lawnmower or
carry it when the power key is switched on. · Do not let persons who do not
know how robotic lawnmower works and behaves use the mower. · Do not put
anything on top of robotic lawnmower or its charging station. · Do not allow
robotic lawnmower to be used with a defective blade disc or body. Neither
should it be used with defective blades, screws, nuts or cables. · Always
switch off robotic lawnmower when you do not intend to use the mower. Robotic
lawnmower can only start when the power key is switched on and the correct PIN
code has been entered.
4
Safety first
EN
· Keep your hands and feet away from the rotating blades. Never place your
hands or feet close to or under the body when robotic lawnmower is in
operation.
· To avoid using the machine and its peripherals in bad weather conditions
especially when there is a risk of lightning. · Not to touch moving hazardous
parts before these have come to a complete stop.
For machines used in public areas, that warning signs shall be placed around
the working area of the machine. They shall show the substance of the
following text: WARNING! Automatic lawnmower! Keep away from the machine!
Supervise children!
2. Additionally when the appliance is operating automatically · Do not leave
the machine to operate unattended if you know that there are pets, children or
people in the vicinity.
MAINTENANCE AND STORAGE
WARNING: When the mower is turned upside down the power key must always be
switched off. The power key should be switched off and the battery removed
during all work on the mower’s under frame, such as cleaning or replacing the
blades.
· Keep all nuts, bolts and screws tight to be sure the applaince is in safe
working condition. · Inspect Landroid each week and replace worn or damaged
parts for safety · Check especially that the blades and blade disc are not
damaged. Replace all blades and screws at the same time if necessary so that
the rotating parts are balanced. · Ensure that only replacement cutting means
of the right type are used. · Ensure that batteries are charged using the
correct charger recommended by the manufacturer. Incorrect use may result in
electric
shock, overheating or leakage of corrosive liquid from the battery. · In the
event of leakage of electrolyte flush with water/neutralizing agent, seek
medical help if it comes into contact with the eyes etc. · Servicing of the
appliance should be according to manufacturers’ instructions.
Recommendation Please only connect Landroid and/or its peripherals to a supply
circuit protected by a residual current device (RCD) with a tripping current
of not more than 30 mA.
Residual risks To avoid injuries, wear protective gloves when replacing the
blades.
Safe transport · The original packaging should be used when transporting
Landroid over long distances · To safely move Landroid within the working
area:
– press the STOP button to stop the mower – select the four digit PIN code
when you start the mower for the first time. – always switch off robotic
lawnmower if you intend to carry the mower. – carry the mower by the handle at
the rear under the mower – carry the mower with the blade disc away from the
body
RF exposure requirements To satisfy RF exposure requirements, a separation
distance of 200mm or more should be maintained between this device and persons
during device operation. To ensure compliance, operations at closer than this
distance is not recommended. The antenna used for this transmitter must not be
co-located in conjunction with any other antenna or transmitter.
Safety Warnings for battery pack · Do not dismantle, open or shred cells or
battery pack. · Do not short-circuit a battery pack. Do not store battery
packs haphazardly in a box or drawer where they may short-circuit each other
or be short-circuited by conductive materials. When battery pack is not in
use, keep it away from other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can make a connection from
one terminal to another. Shorting the battery terminals together may cause
burns or a fire. · Do not expose battery pack to heat or fire. Avoid storage
in direct sunlight.
5
Safety first
EN
· Do not subject battery pack to mechanical shock. · In the event of battery
leaking, do not allow the liquid to come into contact with the skin or eyes.
If contact has been made, wash the
affected area with copious amounts of water and seek medical advice. · Seek
medical advice immediately if a cell or battery pack has been swallowed. ·
Keep battery pack clean and dry. · Wipe the battery pack terminals with a
clean dry cloth if they become dirty. · Battery pack needs to be charged
before use. Always refer to this instruction and use the correct charging
procedure. · Do not maintain battery pack on charge when not in use. · After
extended periods of storage, it may be necessary to charge and discharge the
battery pack several times to obtain maximum
performance. · Recharge only with the charger specified by Worx. Do not use
any charger other than that specifically provided for use with the
equipment. · Do not use any battery pack which is not designed for use with
the equipment. · Keep battery pack out of the reach of children. · Retain the
original product literature for future reference. · Remove the battery from
the equipment when not in use. · Dispose of properly. · Do not mix cells of
different manufacture, capacity, size or type within a device. · Do not remove
battery pack from its original packaging until required for use. · Observe the
plus (+) and minus () marks on the battery and ensure correct use.
6
Safety first
INFORMATION ON LANDROID
WARNING robotic lawnmower can be dangerous if incorrectly used. Read through
the Operator’s manual carefully and understand the content before using your
robotic lawnmower.
EN
WARNING – Keep a safe distance from the machine when operating.
WARNING Operate the disabling device before working on or lifting the
machine.
WARNING – Do not ride on the machine.
Li-Ion battery. This product has been marked with a symbol relating to
`separate collection’ for all battery packs and battery pack. It will then be
recycled or dismantled in order to reduce the impact on the environment.
Battery packs can be hazardous for the environment and for human health since
they contain hazardous substances.
Do not burn
Batteries may enter water cycle if disposed improperly, which can be hazardous
for ecosystem. Do not dispose of waste batteries as unsorted municipal waste.
Prohibit disassembling the machine without authorization
Waste electrical products must not be disposed of with household waste. Please
recycle where facilities exist. Check with your local authorities or retailer
for recycling advice.
Class III appliance
Read operator’s manual Detachable supply unit Your Landroid can be used with
other Worx functional accessories. Visit www.worxlandroid.com to learn more
about these available accessory options.
7
Get familiar with Landroid
EN
WHAT’S IN THE BOX
A
B
C
D
G E
F H
I
J
K
N
L
10 cm 4 cm
26 cm
10,2 inch.
M
A Worx Landroid B Wire repair connectors C Spare blades kits D Allen key E Charging pile F Charging base G Screws
H Wire pegs I Power supply J Boundary wire K 20V battery L Boundary wire distance gauges M Bertelsen ruler N Manuals
8
Get familiar with Landroid
GETTING TO KNOW LANDROID
Battery slot Safety stop
EN
A
Find My Landroid / Radio Link slot USB port
Voice Control Slot / High Pitched Alarm Slot Microphone hole
Cutting height adjustment
Battery cover button
Interface ACS slot
B
Rain sensor
Charge contact
Off Limits slot
The picture is for reference only
9
Get familiar with Landroid
EN
HOW LANDROID WORKS
In the following section, we would like to help you better understand how
Landroid works. Landroid is an autonomous machine, capable of operating on its
own. It knows when it needs to go to its charging base, can sense when it is
raining, can stop itself if it senses a problem and knows to stop, draw back,
and turn around when it bumps into something blocking its path. To prevent an
accident, Landroid will also automatically stop its blade disc from rotating
if it is lifted off the ground.
Charges itself
When your Landroid needs to recharge, it will stop mowing and follow the boundary wire in an anti-clockwise direction back to its charging base. Once charging is complete, Landroid will automatically resume mowing or stay in the charging base according to its mowing schedule.
Border management
Landroid is programmed to mow the grass along the perimeter of your lawn twice
a week on Monday. If you want to change this pre-set, you can modify it via
your smartphone or by using the control panel in “Work time-Customise Work
time” menus. See detailed instructions at the end of this manual.
Rain sensor
Landroid is 100% weather proof and happy to be outside. But mowing wet grass
does not give you the best finish or result. Landroid is equipped with a rain
sensor which detects rain and tells Landroid to stop mowing and go back to its
charging base.
Rain delay time
After a rainfall, Landroid re-starts when the grass is no longer wet. The
default Rain Delay time is 180 minutes. You can change the Rain Delay time
setting via Landroid App.
In more extreme weather…
In case of a lightning storm, protect Landroid by unplugging the charging
base, disconnecting the boundary wire, and making sure Landroid is not allowed
to charge. In the Winter and especially in case of very cold weather and snow,
we recommend you store your Landroid inside. In some countries we offer a
Winter servicing of your Landroid so it’s ready for the Spring growing season.
Contact your dealer or check online for more details.
10
How Landroid works
EN
No more grass clippings to collect
Landroid’s daily mowing produces very short clippings that don’t need to be
raked. These clippings are a perfect organic nutrient for your lawn. Frequent
mowing boosts the density of grass blades and effectively prevents the
propagation of weeds.
Cut to edge
The special offset blade gets as close as possible to the border of your lawn,
leaving you little or no trimming to do.
Cutting Height
Before starting your Landroid for the first time, make sure your grass is no
longer than 10cm. If longer, use a regular mower to cut it before operating
Landroid. If you want to drastically shorten the height of your grass, it is
recommended that you do so progressively, by adjusting the cutting height in
steps.
Security & PIN Protection
To prevent unauthorised people from being able to use it, Landroid is
protected by a PIN code that you can easily set up
Self-levelling cutting deck
Ground Tracer automatically adjusts the blade’s hight to match the natural unevenness found in most lawns.
11
Getting started
EN
INSTALLING LANDROID YOURSELF? EASIER THAN YOU MAY THINK
Installing your Worx Landroid is easier if you carefully follow these
instructions. In the end, it is a matter of installing the charging station
and laying the boundary wire all around your lawn. In addition to this manual,
you can use the Get Started guide that’s inside the box and watch the
comprehensive video tutorials on our YouTube channel*.
- This information is provided for your convenience but does not replace the instruction manual and the safety instructions that needs to be read and understood.
Patrol your lawn to plan installation
Install the charging station
Lay the boundary wire
Connect charging station to AC
Power up Landroid. Test and get ready to mow
EVERY MINUTE SPENT IN PLANNING SAVES YOU 10 MINUTES IN EXECUTION
Installing Landroid is even easier if you have made a clear idea of what you
need to do. A proper planning will also help you avoid mistakes or having to
rework the installation once it’s done.
On the surface or buried? Landroid’s boundary wire is designed to stay on the
surface of your lawn. Nearly invisible from the first day, it will be engulfed
in the soil in a few weeks. If you will want to bury the wire, it is
recommended to first peg it down and test the installation is successful by
running Landroid over the perimeter. This allows you to easily check
everything and, if necessary, change the layout before burying the wire. Bury
the wire no more than a few centimetres below ground level, so that the wire
ensures good signal.
Plan for the charging station The charging station, composed of the base plate
abnd the charging tower, is where your Landroid goes to have its battery
recharged. It’s also the parking lot where it rests in between one mowing
session and the next. Locate a proper position for it, bearing in mind: · It
needs to be powered, so it should be no more than 10m away from an AC mains
outlet · If possible, choose a shaded position as batteries and chargers don’t
like over-heating · The base needs to sit on flat land to ensure effective
docking · Avoid places close to irrigation sprinklers
12
Getting started
EN
You can place the charging station on your lawn or on a hard surface like a walkway, provided that the lawn and the hard surface are at the same height (no steps).
To enter the station, Landroid needs at least 80cm straight path in front. On the exit side, it needs at least 30cm straight path before a left turn (fig. 1). If the turn is to the right, there is no need for a straight path (fig. 2).
1
2
30cm
80cm
80cm
The charging base should never be positioned on a slope (fig. 3). Make sure it is level and resting on a flat surface (fig. 4).
3
4 0°
0°
Charging station checklist:
within reach of AC mains in shade straight path on entrance; straight path on
exit if necessary flat land no irrigation sprinklers nearby
Plan for the boundary wire The wire has to be placed at a certain distance
from the edge of the lawn. This distance changes depending on what’s on the
other side of the edge. Different parts of your lawn may border different
scenarios: 1. If the edge of the lawn borders a step: keep the wire 26cm from
the edge. 2. If the edge of the lawn borders a path at the same height: keep
the wire 10cm from the edge. 3. If the edge of the lawn borders gravel: keep
the wire 26cm from the edge, as Landroid’s wheels may slip on gravel.
26cm
10cm
26cm
If a side of your lawn borders a neighbor’s lawn with a robotic mower in use,
lay your wire 1m apart from your neighbor’s wire to avoid possible
interference.
13
Getting started
EN
PATROL YOUR LAWN
Landroid is designed to manage the most complex of lawns. Carry out a visual
inspection of your lawn so you are prepared for a trouble-free installation of
the boundary wire.
Identify forbidden areas You don’t want your robot mower to behead flowers,
dive into a water feature, or shred tree roots that emerge from the ground.
Locate these areas and surround them with boundary wire to prevent Landroid
from accessing them.
The boundary wire is a single loop connected on both ends to the charging
station, so you will have to depart with the wire from the border, surround
the area you want to protect, then take the wire back to the border as
illustrated here in fig.1. If areas to be surrounded are far away from the
border of your lawn, or if you have several areas and tree roofs to protect,
this traditional method is time consuming.
A great alternative is to purchase Landroid’s Off-Limits option. With this,
you simply surround forbidden areas with the Off-Limits digital fence, which
does not need to be connected to the boundary loop (fig. 2). The Off-Limits
digital fence is also great to protect seasonal equipment (e.g. a trampoline)
or for protecting new changes to the layout of your lawn without having to
rework the boundary wire.
1
boundary wire 0cm
2
digital fence
Identify obstacles Landroid’s bump sensor can manage solid obstacles such as trees, furniture and the like, which don’t need to be surrounded by wire. If your lawn has several obstacles and trees close to each other, we recommend you to purchase the Landroid ACS option, an intelligent ultrasonic auto-pilot that makes your Landroid steer around obstacles instead of bouncing into them.
14
Getting started
EN
NOW ROLL YOUR SLEEVES UP. WHEN IT’S DONE IT’S DONE!
Now that you have planned the installation in every detail, you are ready to
take action. Before starting, you may want to use your old mower for the last
time to clean up your lawn and make the installation easier.
Fix the charging station in the selected location Insert charging tower into
charging base. Secure the base to the ground by means of the supplied screws,
using the supplied Allen key (fig.1). If you position the base on hard
surface, fix it with plug and screw fixings (not supplied)
1
Connect one end of the boundary wire to the charging station · Strip the end of the wire with a pair of scissors (fig. 2) · Open the plastic door and insert the stripped end into the red left clamp (fig. 3) · Pass the wire through the guide of the base, as shown in fig. 3
2
3
OUT
Lay the boundary wire around your lawn · Use the supplied gauge to set the distance wire to edge · If there is a step at the edge of your lawn, keep the wire at 26cm from it (fig. 4) · If there is no step, keep the wire at 10cm from the edge (fig. 5)
4
5
26cm
10 cm
4 cm
26 cm 10,2 inch.
10cm
10 cm
4 cm
26 cm
10,2 inch.
15
Getting started
External corners of 90° Rounds external corners of 90° as shown in figure 6.
6
90°
EN
External corners less than 90° In special conditions (wet grass, excessive
slopes, presence of earth or mud), the Landroid may slip at sharp angles and
the turf may be damaged. To prevent this problem, we advise those who have a
garden with these conditions to cut the corner and create two corners greater
than 90° as shown in figure 7.
7
90° >90°
Secure the wire to the ground using pegs · Place pegs at approximately 80cm to each other (fig. 8) · Make sure the wire is always in close touch with the ground (fig. 9)
8
9
80cm
80cm
80cm
16
Getting started
Lay perimeter islands, if needed · Protect flower beds, ponds, tree roots and
other areas by surrounding them with the boundary wire · Depart the edge at a
right angle to reach the area to be protected · Surround the area with the
wire, keeping 26cm distance, until you close the island · Always lay the wire
clockwise. Failing to do so will make the mower drive into the island · Return
to the edge of the lawn following the same path
10
EN
Bertelsen method: how to make perfect 90° angles with corners facing the lawn
If there are 90 degree corners that face the inside of your lawn, use the
Bertelsen ruler to help Landroid make perfect turns (and remove the risk that
Landroid hits an obstacle on the border of the lawn whilst doing this
manoeuvre).
11
26cm
26cm 26cm
Close the loop Once you have completed laying the wire on the perimeter of
your lawn, you will arrive back to the charging base. · Pass the wire through
the guide in the base, up to the clamp (fig.12) · Cut the exceeding wire and
strip the end with a pair of scissors · Insert the stripped end into the black
right clamp
12
IN
17
Getting started
EN
Final steps The boring part is over! There are only a few more steps to go: ·
Connect the charging station to the AC mains socket (fig. 13) · If everything
is fine, the LED will light green · If there’s a trouble in the loop, such as
broken wire or wire ends not properly clamped, the LED will turn red. Check
that everything is
fine and see the FAQ session if the problem persists
13
· Open the rear of Landroid and insert the PowerShare battery into the slot
until it clicks (fig.14)
14
CLICK!
· Place Landroid on charge by making sure a good contact is established with
the base (fig. 15). The LED will blink green; once the battery is fully
charged, the LED will turn solid green.
15
Let Landroid charge the battery for a while. Whilst it is charging you may want to take a well-deserved break: get familiar with the following instructions, and connect Landroid to your Wi-Fi network.
18
Getting started Joining up the boundary wire
EN
Landroid box includes two small, waterproof boundary wire connectors. They can
be used for the following: · When your lawn has a very long perimeter and you
need extra boundary wire to complete the installation. Please do not exceed
350m
of boundary wire: this is the maximum length of the boundary wire perimeter ·
When the bounday wire is cut by accident and you need to fix it · When you
decide to rework your garden in the future and need to modify the original
boundary wire installation
The connectors are waterproof and provide optimal electric connection. ·
Insert both ends of the wire into any two of the three holes of the connector;
no need to strip the wires · Insert the wires fully until both wire ends are
visible on the other side of the connector · Press the connector firmly by
using a pair of pliers
Attention: it is not recommended to simply splice the boundary wire with
insulating tape or use a screw terminal block for connection. A broken circuit
may occur after a period of time as soil moisture can oxidize the wire.
19
Getting started
NOW FOR THE EXCITING BIT! START LANDROID FOR THE FIRST TIME.
Get familiar with the control panel Landroid’s control panel provides the key
functions in a minimalistic design. For advanced functions, the free Landroid
app provides further options in a richer interface: your smartphone.
EN
Wed.11/29 09:00PM
START: start mowing
HOME: send Landroid to charging station during operations and activates
STOP
DISPLAY
RETURN: back one step to former menu POWER: turns Landroid on and off.
Desabling device prevents operation of Landroid KNOB: select and enter
Starting Landroid · Position the Landroid inside the work area · Press and
hold down until the display lights up · Enter the default PIN code 0000 by
pressing four times. The display will show 0000. Press again to confirm
The display will show “PIN code OK” · Press the button and then the button to
confirm. The Landroid will start mowing the lawn · You can stop the Landroid
at any time by pressing the large red button · To send the Landroid to the
charging base, press the button and confirm by pressing .
20
Getting started
EN
LANDROID CONTROL PANEL
Advanced functions via the built-in interface Despite its minimalistic design,
you can set several advanced functions through the built-in control panel.
However, for the best user experience we recommend you use the free Landroid
app to do this, given its much richer and intuitive interface.
1. Settings · To access the main menu, rotate clockwise · Rotate to select
the menu items:
“General settings” “Working time” “Security” then press to enter. · Use the
same procedure for the following actions.
Wed.11/29 09:00PM
Wed.11/29 09:00PM
1 2
General setting Language Time format Date format Set time
Only for reference
General settings
Navigation Page *
Working time
Language Time format Date format Set date & time Rain start delay App link
Diagnose**
Auto Work Time Customize work time Define zones Customize work zone
Security
Change PIN code
- Be continuously updated according to the software version. ** For after-sales service only
2. Set date and time · Return to “General settings” · Rotate clockwise to
select “Set date & time”, then press to enter. · Rotate clockwise to select
the date, then press to confirm. The selected option (day, month or year) will
start flashing. · Rotate to select the day, month or year and press quickly to
confirm. Use the same method to complete
the “Year / Month / Time”.
21
Getting started
EN
3. Set work schedule Note: it is possible to set two work schedules per day:
“Scheduler #1” and “Scheduler #2” · Return to the main menu and rotate
clockwise to select “Working time”, then press to enter. · Rotate clockwise to
select “Customize work time”, then press to confirm. · Rotate clockwise to
select the day of the week, then press to confirm. · Press to enter settings ·
Rotate clockwise to activate “Scheduler #1 *”. Press to confirm. · Rotate
clockwise. Select the start time “Hour/minute” and press to enter. The
selected number will start flashing. · Rotate to select the time you want the
Landroid to start working on that day, and press to confirm.
Follow the same procedure to set the time to stop work. · Next, rotate
clockwise to select “Border cut” and press to enter settings. · Rotate
clockwise to choose whether or not to activate “Border cut” and press to
confirm. · If you want to set a second working time (“Scheduler #2”), follow
the same procedure. · Press the button and follow the same procedure to set
the other days of the week.
4. Working time adjust · You can rapidly adjust the work time of the week.
The increment /decrement of time will be evenly allocated to required working
days. · Return to main interface. · Anticlockwise rotate to activate the
working time adjust.
Note: The total time is based on the customize work time, and can be adjusted
by gradient of 10%. · Then rotate to adjust and short press to confirm.
5. One time schedule To cut the lawn on a day or at a time outside the
programming period, simply start the Landroid by pressing the button and then
the button to confirm. However, in this case the Landroid will only cut the
lawn for the duration of the battery life and once back at the base for
charging it will stay there until it is programmed to start again.
However the new “One time schedule” function allows a precise working time to
be programmed with a border cut option. It is also possible to decide whether
at the end of the cutting session the Landroid should return to the charging
base or switch off on the spot. This is very useful in any situation where an
area of the lawn is not connected by a path that the Landroid can travel over
to the main lawn (where the charging base is located), i.e. those areas where
the Landroid needs to be transported by hand, preventing it from continuing to
operate until it runs out of battery.
If the Landroid has access to the recharging base. Note: to activate the
“Border Cut” option, the Landroid must be positioned in the charging base. ·
Position the Landroid at the recharging base · Go to the main menu · Quickly
press the button three times · Rotate clockwise, select “Charging base – Yes /
No”, then press to enter settings. · The selected word will flash. Select
“Yes” and press to confirm · Rotate to select “Enable Border Cut – Yes / No”,
select the desired option and confirm. · Follow the same procedure to select
the “Working Time”. · Rotate clockwise to choose whether or not to activate
“Start” and press to confirm. Once the battery has run out, the
Landroid will return to the base to recharge and, if necessary, restart in
accordance with the newly set working time.
If the Landroid does NOT have access to the charging base. Note: the option
“Border Cut” is not available for areas without access to the charging base ·
Go to the main menu · Quickly press the button three times · Rotate clockwise,
select “Charging base – Yes / No”, then press to enter settings. · The
selected word will flash. Select “No” and press to confirm · Follow the same
procedure to select the “Working Time”. · Rotate clockwise to choose whether
or not to activate “Start” and press to confirm. Once the battery or
working time has run out, the Landroid will shut down on the spot.
22
Getting started
EN
CONNECTING LANDROID TO THE INTERNET
Why connect Landroid Landroid is an IoT (Internet of Things) device. To get
full functionality out of your Landroid and keep it always updated to the
latest software, it must be connected to the internet via your Wi-Fi network .
BEFORE YOU START
1. Dowload the app Download the free Landroid app first. Get it from Android or Apple app stores.
GET IT ON
Available on the
2. Ensure you have:
· Your WiFi network password/bluetooth function on your smartphone. · Landroid
Serial Number: it can be found in the label under the rear bonnet of the
machine.
If you don’t want to type the 20-digit Serial Number, input it by scanning the
QR code with your smartphone’s camera.
Label and QR code
3. Check your Wi-Fi settings
· Landroid works with 2.4GHz Wi-Fi signal · Make sure your Lasndroid is in the
same router environment as your smartphone · Make sure the distance between
your Landroid, smartphone and your router is as close as possible during
connection
Tip: when Landroid moves to an area of your lawn with poor or no Wi-Fi signal,
instructions sent from the app will only be executed when Landroid returns to
an area with good signal.
Bluetooth function · Make sure Buletooth function on your smartphone is
activated. · Make sure your Landroid is within the connectable distance.
23
Getting started
EN
LANDROID APP NOT A SIMPLE REMOTE CONTROL
Don’t think at it as a remote control. The app is an integral part of the Worx
Landroid advanced ecosystem based on cloud computing and artificial
intelligence.
Thanks to the app’s augmented reality feature, you can measure the exact area
of your lawn. It’s as easy as taking a walk along its border.
You can use the app to upload information on your grass species, soil type and
irrigation. These inputs, in combination with weather data and lawn size, will
allow our cloud computing to tailor-make your Landroid’s working schedule to
the actual growth of your grass, everyday.
The app also lets you view statistics on what Landroid has been doing for you.
If you ever need to get your Landroid serviced, you can even open a service
ticket by using the app.
The app also notifies you when there’s new software available for Landroid to
download automatically over the air.
Once connected, Landroid can access its unique auto scheduling instructions from the cloud and is able to download the latest software to optimise its performance.
24
Maintenance
EN
MAINTENANCE
Your Landroid works hard and needs to be cleaned and checked from time to
time. This section of our guide helps you keep Landroid in good shape so it
can last for years without troubles. Here’s how to take care of your Landroid.
Turn off the machine before carrying out any service or maintenance.
KEEP IT SHARP
Landroid does not cut grass like other mowers. Its cutting blades are razor
sharp on 2 edges and rotate in both directions for maximum cutting capacity. ·
The blade turning disc makes a clockwise and counterclockwise rotation at
random to use both cutting edges and minimize the
frequency of replacing the blades · Each cutting blade will last up to 2
months when it is programmed to mow every day · Always check to see if the
blades are chipped or damaged and replace them if they are · When the cutting
blades are dull and worn out, they should be replaced with the spare blades
provided with your Landroid.
Spare blades are also available at your nearest Landroid retailer
WARNING! Before cleaning, adjusting, or replacing the blades, turn your Landroid OFF and remove the battery. Always wear protective gloves.
Replacing the Blades
Remove the battery (fig.1) and gently flip the Landroid over (fig.2)
1
2
Take the screws off the blades with a screwdriver (fig. 3 – 4)
3
4
25
Maintenance
Firmly screw on the new blades (fig. 5 – 6)
5
6
EN
Attention: When fitting new blades, make sure you replace ALL the blades. ·
Always use new screws when fitting blades. This is important to ensure blade
retention and balance the blade turning disc. Failure to
use new screws could cause serious injury · Important: After screwing the
blade to the blade disc, make sure the blade is able to spin freely
KEEP IT CLEAN
Your Landroid should be cleaned regularly. This helps keep it in good
condition, especially removing dirt, debris and the build-up of grass from
daily mowing. Turn Landroid off before cleaning it. For extra safety, remove
the battery.
WARNING! DO NOT use a hose, high pressure washer or otherwise pour running
water on your Landroid. High pressure water can go inside the sealings and
damage electronic and mechanical parts.
Cleaning the upper body · Clean with a spray bottle filled with water. Don’t
use solvents or polishers · Use a brush or a clean cloth to remove built-up
dirt
Cleaning the Bottom · Flip Landroid upside down · Remove debris and grass
clippings using a brush to remove · Be careful not to touch the blades with
your hands. Wear gloves for protection · Clean the blade disc, the chassis and
the front wheel(s) thoroughly with a soft brush or moist rag · Rotate the
blade disc to ensure it rotates freely. Remove any obstructions. Remove any
lodged debris so that they don’t cause a crack
in the blade disk. Even the tiniest crack effects mowing performance · Check
the blades spin freely around the fixing screws. Remove any obstructions
Cleaning the drive wheels · Remove mud from wheels with a brush in order to
ensure good grip of the tread
Clearing the charging contacts · Clean the contact pins located on the
charging base and the charging strips located on the Landroid using a cloth ·
Periodically remove any build-up of grass clippings or debris around the
contact pins and the charging strips to ensure Landroid
successfully charges each time
26
Maintenance
EN
KEEP IT CHARGED
The heart of Landroid is its 20V Li-Ion Worx Powershare Battery. · For the
proper storage of the battery, make sure it is fully charged and kept in a
cool dry place. · The recommended Landroid operation temperature is between
0-55°C · The life-span of Landroid’s battery depends on hours of usage and the
length of use per day during the mowing season
Battery maintenance during storage · Landroid can be charged manually without
the boundary wire · Connect the charging base to a suitable power supply. The
green light on the charging base will turn on · Manually dock Landroid into
the charging base while Landroid is powered off · The green light on the
charging base will flash and Landroid will begin to charge · When the battery
is fully charge, the green light will turn solid green
KEEP IT STORED OVER THE WINTER
Although Landroid is designed and built to survive the most severe weather
conditions, we recommend storing it in your shed or garage during the winter.
To prepare it for winter hibernation: · Clean it thoroughly · Fully charge the
battery · Turn the power off
Getting back to work in the Spring When it is time to re-start Landroid for
the new season, please perform the following checks: · Update the time and
date settings via the app · If you notice signs of oxidation on the charging
contacts of Landroid and the charging station, clean these with a fine
grade emery cloth · Full charge Landroid’s battery before operating
KEEP IT UPDATED
Landroid is always improving and new software versions are made available for
free. Always keep Landroid software updated to make the most of your machine.
Over-the-Air (OTA) updates If your Landroid is connected to your Wi-Fi
network, you will be notified that new software is available via the app. Once
you confirm, the update will happen automatically Over-the-Air.
Check which software version you have The software version number can be seen
when Landroid is powered on.
27
Maintenance
EN
Manual updates · If your Landroid is not connected to your Wi-Fi network, you
can still update it to the latest software version with a USB stick ·
Regularly visit the Worx Landroid website to check if any new version is
available. If you subscribed to Landroid email list, you will be
notified when a new version is available · Download the latest software
version at our website · Unzip the file on your computer · Take a blank USB
stick formatted in FAT32 · Save the unzipped Landroid software to the USB
stick · Place Landroid on a secure and level surface · Turn off Landroid · Go
to the rear of the Landroid to access the USB port. · Insert the USB stick in
the port · Place the Landroid on the lawn again, inside the working area
delimited by the boundary wire · Turn on Landroid · Without lifting Landroid,
remove the USB stick when “Please remove the USB key” is displayed · The
update will begin automatically and may take a while. Landroid will restart
automatically after the update is completed
NOTE: Make sure Landroid is within the boundary when restarting Landroid.
28
Quick reference
EN
This section contains a guide on operation and potential error messages Landroid displays. There is also a troubleshooting section at the end that is designed to help you understand and solve any issues.
OPERATION MESSAGES
MESSAGE Cutting grass Raining
Going home Charging No working time scheduled Not working today Work done
today Zone searching Charge complete Emergency charge
LANDROID ACTION
Cutting grass according to the mowing schedule.
The rain sensor detects water. Landroid will return to the charging base and
stay there for the time you have programmed it to do so. When dry, Landroid
will automatically begin the rain delay countdown and then return to mow. If
you want Landroid to mow before this, simply turn it off then on again, but
only when the rain sensor is dry, or you can remove the rain delay completely
by setting the rain delay time to zero.
Needs to recharge–during the journey to the base, the cutting blade is stopped
in order to save energy.
Charging’ and charge percentage are displayed. Stand-by, needs to be programmed as desired. Stand-by, will start according to mowing schedule. According to the setting ofCustomize work zone’, Landroid is searching a
certain area to mow.
Landroid has completed its charging.
Landroid is charging in a powered-off state.
29
Quick reference
EN
ERROR MESSAGES
Sometimes things can go wrong. Fortunately Landroid is smart enough to tell
you if it is enountering an issue, so you can fix it. If in doubt, please
visit our website where you will find useful videos and further support.
MESSAGE
CAUSE
ACTION
Outside working area! Press START to reset.
Landroid cannot find the boundary wire signal.
1. If Landroid is actually outside of its working area: turn power off, take Landroid inside the working area, turn the power on and press start.
2. If Landroid is inside its working area check if the LED on the charging base is solid green. If red, check if the boundary wire is properly connected to the charging base and that the base is connected to a suitable power supply. If they are properly connected, the boundary wire terminals are clamped incorrectly and must be reversed.
WRONG PIN! Please retry.
PIN code is wrong.
Input the correct PIN or re-set your PIN.
Blade motor fault! Press START to reset. Blade disc is blocked by an object, e.g. a branch.
Turn power off.
Turn Landroid upside down and check if there’s anything preventing the blade
disc from rotating and remove any obstruction.
Turn Landroid upright. Turn power on. Press start.
Blade is over-loaded by thick dense grass.
Turn power off.
Take Landroid to an area with short grass or adjust the cutting height to a
higher setting.
Turn power on. Press start.
Wheels motor fault! Press START to reset.
Wheel motor is blocked in some way.
Turn power off and take Landroid to an area free from obstacles. Turn power
on. Press start.
If the error message is still displayed, turn power off. Turn Landroid upside-
down and check if there’s anything preventing the wheels from rotating.
Remove any obstruction, turn Landroid upright, turn power on.
30
Quick reference
EN
Upside down! Press START to reset.
This could have happened when
Turn Landroid upright and remove any
Landroid came into contact with a
obstacle that might have caused
sloping surface which made it overturn. Landroid to overturn.
Mower trapped! Press START to reset. Landroid is trapped.
Turn power off.
Take Landroid to an area of your lawn free of obstacles, then turn power on.
Press start.
If the error message is still displayed: turn power off, turn Landroid upside-
down. Check if there is anything preventing the wheels from rotating.
Remove any obstruction, turn the Landroid upright, turn power on.
Mower lifted! Press START to reset.
Landroid is lifted up.
Turn power off.
Take Landroid to an area clear of obstacles, turn power on. Press start.
If the error message is still displayed: turn power off, turn Landroid upside-
down and check there’s anything that can cause Landroid to be lifted up.
Remove any possible object, turn Landroid upright, turn power on.
Battery voltage too low! Please change Battery exausted. battery.
In this case you must turn Landroid off and place it in the charging base, then `Emergency charging’ will be displayed and it will start charging. If the battery error still persist, your battery is damaged and need to be changed.
Wire missing! Press START to reset.
Machine can’t find boundary wire signal.
If the LED light is red, check if the boundary wire is well connected to the clamps on the charging base. If the problem persists, check that the boundary wire hasn’t been cut.
Battery temperature out of range! Please wait.
Temperature is too high (more than 55°C) or too low (less than 0°) when charging.
Place the charging base in a shady area or wait until it reaches the normal temperature.
Battery pack cover is opened.
Close the battery pack cover.
31
Quick reference
EN
Can’t find charge station press START to reset.
Boundary wire is beyond its maximum length (350m or machine doesn’t have enough power to go back to charging station.
Take Landroid to the charging station.
Mower locked!
With the `Lock Function’ enabled, if your Landroid does not receive a signal
from your Wi-Fi router for 3 days, then it gets locked as a security measure.
This could be because your router lost its power or because you changed your
Wi-Fi router or network provider.
Please reconnect Landroid to the Wi-Fi networtk it has been originally paired
with.
If this is not possible, contact Cutomer Service.
NOTES · Before turning power on, always check Landroid is inside its working
area. If not, the message “Outside working area! Press START to
reset” will be displayed. This message is also displayed when Landroid is
partly but not completely inside its working area · If for any reason–i.e. a
party, children playing…–you want to park your Landroid in the charging base:
press home then . Landroid
will go to its base and stay there. Please note Landroid will now wait until
the next scheduled mowing session. If you want to re-start it at anytime,
press start then to start your Landroid · If an error repeatedly occurs in the
same area of your lawn, you might have a problem with the boundary wire so
please refer to the installation instructions and check your set up is correct
with its help · If your lawn is divided in two separated areas, connected by a
corridor less than 1m wide, one of which is not provided with the charging
base: when Landroid runs out of charge, take it manually to the charging base
· If Landroid runs abnormally once in a while, please reset it by turning it
off and removing the battery for 30 seconds, then restart it. If the problem
cannot be solved, please contact our Customer Service for help
32
Quick reference
EN
TROUBLE SHOOTING
If your Landroid does not work correctly, follow the trouble shooting guide
below. If the fault persists, contact Customer Service.
SYMPTOM
CAUSE
SOLUTION
The LED light on the charging base does not turn on.
There is no power.
Check the charging base is connected properly to the charger and the charger is connected to a suitable power supply.
Red light on the charging base.
The boundary wire isn’t connected.
Check that the boundary wire has been connected correctly to the charging base. Check there are no breaks in the boundary wire.
Landroid turns on, but the blade disc does not spin.
Landroid is searching for the charging base.
This is normal: when Landroid needs to recharge, the blade disc does not rotate while it is searching for the charging base automatically.
Landroid vibrates.
The blade disc is unbalanced. Blades may be damaged.
Check the blades and replace them if damaged. Remove debris and foreign objects from the blades and blade disc.
Grass is being cut unevenly.
Landroid does not work enough hours Try adding more hours to the mowing
per day to cut the grass.
schedule.
Mowing area is too big for the size of Landroid you have.
Try decreasing the size of the mowing area.
The blades are dull and not sharp.
Change all the blades and screws in order to balance the bade disc.
The cutting height is set too low for the Raise the cutting height and then
length of the grass.
gradually lower.
Grass or another object has wrapped around the blade disc.
Check the blade disc and remove any grass or other objects that might prevent it spinning.
There is a build-up of grass in the blade Make sure the blade disc rotates easily.
disc or motor frame box.
If need be, you may take off the blade
disc and then remove the debris.
Your Landroid is inside its working area The boundary wire ends are clamped and the boundary wire is connected, but incorrectly. the display says `Outside working area! Press START to reset’
Reverse the boundary wire ends and reconnect to the charging station.
33
Quick reference
EN
The charging time is far more than the rated charging time.
Poor connection caused by debris on the charging strip.
Clean the contact pins located on the charging base and the charging strip on Landroid using a cloth.
The charging protection program is activated due to high temperature.
Place the charging base in a shady area or wait until the temperature has cooled down.
The mower does not charge.
There is no power.
Check the power cord is connected properly to the charger and the charger is connected to a suitable power supply. Make sure both the charging strips on the mower touch the centre of the contact strips on the charging base.
Landroid is starting to have shorter run-times between charges.
Something is clogging in the blade disc creating friction and increasing power consumption.
Take off the blade disc and clean it. Maybe the grass is too high and too thick.
Landroid is shaking heavily because the blade disc is unbalanced.
Check the blade disc and blades, remove debris and foreign objects from the blades and blade disc. Replace the blades with a new set.
The battery may be exhausted or old. Replace battery.
The working time is up.
Reset the woking time.
Landroid is not operating at the correct time.
The clock is not set to the correct time.
Programmed cutting times for Landroid are not correct.
Set the clock to the correct time.
Change the time settings for the mower to start and stop.
The percentage of weekly operating time set through app has changed.
Set the correct percentage through app.
Landroid cannot correctly dock with the charging base.
Environmental influences.
Poor connection caused by debris on the charging strip.
Restart Landroid.
Clean the contact pins located on the charging base and the charging strip on
Landroid using a cloth.
The green light on the charging base turns on before charging is complete.
The charging base is overheating or overcooling.
Place the charging base in a shady area or wait until it reaches the normal temperature.
Landroid wheels skid or repeatedly slip. Foreign obstacles, such as twigs and branches may be lodged under Landroid.
Remove foreign objects from underside of Landroid.
The lawn is too wet.
Wait until lawn has dried.
34
Quick reference
EN
Landroid runs outside the boundary wire.
Landroid does not mow an area within a boundary wire zone.
Landroid reverses or rotates erratically near the boundary wire.
The boundary wire of another Landroid or robotic mower is positioned too
closely.
In wet conditions, the boundary wire electric signal may leak where the wire
has been joined or repaired incorrectly.
There is boundary wire electric signal leakage due to broken insulation.
Ensure at least 1m clearance is provided in between your boundary wire and
that of your neighbor.
Check boundary wire joints. Insulate to provide a fully waterproof connection.
Repair damaged boundary wire with the wire connectors supplied.
Landroid slips out of its working area going down a hill.
Low grip of Landroid drive wheels.
Please check the wheels are clean and free of mud in order to have the maximum grip possible.
Landroid operative system crashes when charging or on standby.
Software or display fault.
Restart Landroid.
Landroid shuts off when docking in the charging base.
Landroid fails to charge due to over temperature protection and is powered off.
Place the charging base in a shady area or wait until the temperature has cooled down.
Poor connection.
Check the LED light on the charging base.
Check the connection between the contact pins located on the charging base and
the charging strip.
Landroid stops in the working area.
There is an obstacle in the working area. Remove the obstacle from Landroid’s working area.
The cutting height is set too low for the length of the grass or the grass is too dense.
Raise the cutting height and then gradually lower.
The extended boundary wire should not Reduce the lenght of the boundary wire. exceed 350m or it may cause signal problem.
The distance between the center of the lawn and the boundary wire should not exceed 25m or it may cause signal attenuation.
Reduce the distance between the center of the lawn and the boundary wire perimeter within 25m.
Landroid flips over.
There is an inclined obstacle on the lawn.
Exclude the obstacle from Landroid’s working area.
35
Quick reference
EN
Landroid fails to connect to the internet. Please check your router has the correct Make sure your router is 2.4GHz. If your
settings.
router has two settings, please enable
the 2.4GHz band.
Make sure your router is set to 802.11 mode and wireless setting is b/g/n mixed.
Make sure your router has the SSID Broadcast function enabled when you connect the machine with the app. You can close it after you connect successfully.
Make sure DHCP function is enabled.
If you changed your Wi-Fi network, you need to connect Landroid to the new network.
If you have a “Fritz!box” router, please make sure activate “Allow communication between devices in same network” in the settings.
Your Landroid beeps when you are adjusting “month / hour /minute”
Please check whether the router is disconnetcted or Wi-Fi SSID is changed.
It is normal.
Make sure the router is connected and Wi-Fi SSID is correct.
Anticlockwise to adjust.
Environmental protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
36
Quick reference
EN
TECHNICAL DATA
Type WR165E WR167E WR148E WR147E.1 (100-199 – designation of machinery,
representative of Robotic Lawnmower)
WR165E
WR167E
WR148E
WR147E.1
Rated voltage
20 V Max.*
No load speed (/min) Cutting area (m2)
2800
500
700
2400
800
1000
Cutting diameter (cm)
18
20
Cutting height (mm) Cutting height positions Battery type
30-60 4
Lithium-ion
Battery model Charging time approx. (mins) Charger model
Charger rating
Machinery weight (kg) Protection degree
WA3551.3
WA3553.3
WA3551.3
75
150
75
WA3750.1/ WA3755.1
Input: 100-240 V~50/60 Hz, 38 W, Output: 20V ,1.5 A
9.5
9.8
11.7
III
WA3553.3
75
WA3775 / WA3776 Input:100-240 V~50/60 Hz, 90 W, Output: 20 V ,
3.0 A
12
App (Wifi/Bluetooth)
Frequency band of embedded WLAN module
Max. radio-frequency power of embedded WLAN module
Frequency band of inductive loop systems
Y
2.412GHz-2.484GHz 802.11b:+16±2dBm(@11Mbps) 802.11g:+14±2dBm(@54Mbps)
802.11n:+13±2dBm(@HT20,MCS7)
77 Hz
Max. radio-frequency power of inductive loop systems
82 dBµA/m
*Voltage measured at no load. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is 18 volts.
37
Quick reference
EN
NOISE DATA
WR165E
WR167E
WR148E
WR147E.1
A weighted sound pressure A weighted sound power
LpA = 50.83 dB(A) KPA = 3.17 dB(A) LwA = 61.83 dB(A) KwA = 3.17 dB(A)
Wear ear protection when sound pressure is over 80 dB (A).
LpA = 40.68 dB(A) KPA = 1.36 dB(A) LwA = 61.56 dB(A) KwA = 1.36 dB(A)
A degree of noise from the machine is not avoidable. Route noisy work is to be licensed and limits for certain periods. Keep rest periods and they may need to restrict the working hours to a minimum. For their personal protection and protection of people working nearby, an appropriate hearing protection shall be worn.
ACCESSORIES
Screw Charging station Charging base fixing nails Boundary wire Wire pegs Hex key Boundary wire distance gauge Blade Connector Battery pack (WA3551.3) Battery pack (WA3553.3) Charger (WA3750.1/ WA3755.1) Charger (WA3775 / WA3776)
WR165E 9 1 8
130m 180
1 2 9 2 1 / 1 /
WR167E 9 1 8
150m 210
1 2 9 2 / 1 1 /
WR148E 9 1 8
150m 210
1 2 9 2 1 / 1 /
WR147E.1 9 1 8
180m 250
1 2 9 2 / 1 / 1
We recommend that you purchase genuine accessories listed in the above list from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice.
INTENDED USE
The garden product is intended for domestic lawn mowing. It is designed to mow
often, maintaining a healthier and better looking lawn than ever before.
Depending on the size of your lawn, your Landroid may be programmed to operate
at any time or frequency. It is impossible for digging, sweeping or snow
cleaning.
38
Quick reference
EN
DECLARATION OF CONFORMITY
We, Positec Germany GmbH Grüner Weg 10, 50825 Cologne, Germany
On behalf of Positec declare that the product Description Robotic Lawnmower Type WR165E WR167E WR148E WR147E.1(100-199 – designation of machinery, representative of Robotic Lawnmower) (Serial number is placed on the back page) with battery charger WA3775 / WA3776 / WA3750.1/ WA3755.1 and charging station WA4002.1 Function Cutting grass
Complies with the following Directives, 2006/42/EC, 2014/30/EU, 2014/35/EU, 2011/65/EU&(EU)2015/863, 2000/14/EC amended by 2005/88/EC, 2014/53/EU
WR165E WR167E 2000/14/EC amended by 2005/88/EC – Conformity Assessment Procedure as per – Measured Sound Power Level – Declared Guaranteed Sound Power Level
Annex V 61.83 dB (A) 67 dB (A)
WR148E WR147E.1 2000/14/EC amended by 2005/88/EC – Conformity Assessment Procedure as per – Measured Sound Power Level – Declared Guaranteed Sound Power Level
Annex V 61.56 dB (A) 63 dB (A)
The notified body involved Name: Intertek, Semko AB (notified body 0413) Address: Torshamnsgatan 43164 22 Kista Sweden Certification No. : 201002326SHA-V1
Standards conform to, EN 60335-1:2012+A11+A13+A1+A14+A2:2019, EN 50636-2-107:2015+A1+A2:2020, EN 60335-2-29:2004+A2+A11:2018, EN 62233:2008, EN 55014-1:2017+A11:2020, EN 55014-2:2015, EN IEC 61000-3-2:2019, EN 61000-3-3:2013+A1:2019, EN ISO 3744:2005, EN 300 328 V2.2.2, EN 301 489-1 V2.2.3, EN 301 489-17 V3.2.4, EN IEC 62311:2020, EN 61558-1:2005+A1:2009, EN 61558-2-16:2009+A1:2013, EN 55011:2016+A11:2020, EN 303 447 V1.1.1, EN 55032:2015+A11:2020, EN 55035:2017+A11:2020
The person authorized to compile the technical file,
Name
Marcel Filz
Address Positec Germany GmbH, Grüner Weg 10, 50825 Cologne, Germany
2020/12/02 Allen Ding Deputy Chief Engineer, Testing & Certification Positec Technology (China) Co., Ltd 18, Dongwang Road, Suzhou Industrial Park, Jiangsu 215123, P. R. China
39
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>